Boat antifouling Standard Plus

self-polishingfor steelfor wood

Product description
Self-polishing antifouling formulated with copper salts for use on wood, steel or fibreglass boats of medium speed up to 30 knots. The application of minimum 2 coats of antifouling is recommended.

Usage
SURFACE PREPARATION AND APPLICATION PROCEDURE
Bare Steel. Apply 1 coat of EPOFOND AM-9 on sandblasted steel according to SA 2,5/3 and let dry for 12-24 hours. Apply then 2 coats of EPOFOND AM-9 allowing max. 24 hours between coats (minimum 6-8 hours). Overcoat then with 2 coats of STANDARD PLUS antifouling allowing min. 18-24 hours between coats.

Bare Wood. Apply one coat largely diluted of EVIOX CROMOMINIO and allow to dry for 8-12 hours. Apply 2 coats of SOLVER PRIMER allowing 24 hours between coats followed by 2 coats of STANDARD PLUS antifouling allowing min. 18-24 hours between coats.

New Fibreglass. Degrease with suitable cleaner and water and rinse the surface to be coated. Sand with fine abrasive paper and remove dust. Apply 1 coat of EPOFOND AM-9 or POLIFIBER PRIMER and after 24 hours sand with fine abrasive paper. Apply then 2 coats of STANDARD PLUS antifouling allowing min. 18-24 hours between coats.

Previously Coated Surfaces. If the old antifouling is still in sound condition, compatible, and well adhered to the substrate, apply 1-2 coats of SOLVER PRIMER followed by 2 coats of STANDARD PLUS antifouling allowing the required waiting time between coats. If the old antifouling is in poor condition or not compatible, remove the old paint down to bare surface and follow the directions for bare surfaces.

Recommendations
After the application of the last coat the maximum launching period of the antifouling is 1 month; with top quality copper based antifouling and after agreement with technical staff, the launching time may extend up to 3 months, provided that the hull is protected from moisture, rain or atmospheric agents with plastic cover or similar material.

Colour
The color of the antifouling paint after immersion in water may result slightly different since small color differences can occur between different production lots: if necessary, mix them before application.

Remarks
The values specified in the present technical data sheet may vary slightly from one batch to another. The antifouling paint must not come in contact with water, chemicals or be subjected to mechanical stress before the curing is complete. The wet film thickness refers to the undiluted product. In case of dilution, this value increases. The above information is the result of laboratory tests and practical experience and may be subject to revision.

Technical Characteristics / Application Data

• Product code: 3E
• Product name: Standard Plus
• Paint Type: One component
• Binder type A: Natural resins modified
• Specific gravity kg/lt (±0,05): 1.55 - 1.65 according to colour
• Solids content (volume) ±2: 42%
• Viscosity Ford Ø8 at 20°C ±2: 12 sec.
• Shelf life +23°C (±2): 36 months in unopened cans
• Application: Brush-Roller-Spray
• Brush-Roller: Ready to use or max 5% Thinner 400
• Spray: 10% Thinner 400
• Touch dry: 3-4 h (20°C)
• Launching time: Min 24-48 hours
• Recoat time: 18-24 h (20°C)
• Application temperature: Between +10°C and +40°C
• Relevant humidity: Less than 80%
• Dry film thickness advised: 50-60 microns per coat
• Theoretical coverage m2/Lt: 10-12
• Recommended number of antifouling coats: Minimum 2 coats
• Suitable substrates: Wood, steel, fibreglass
• Colours and codes: ROSSO OX (3E3922), NERO (3E4240), BLU UNIVERSO (3E5975), AZZURRO (3E6199)