- Maritime equipment >
- Navigation, Communications, Electronics >
- Analog converter
Analog converters
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}

Voltage: 24 V
Universal CAN Converter The Universal CAN Converter AHD-UCC is a microcontroller-controlled unit for logging and conversion of measuring point data from communication protocols of external CAN-bus networks ...
Böning Automationstechnologie GmbH & Co KG

Voltage: 24 V
Video Signal Converter for AHD-VC Cameras The video signal converter AHD-VSC C is used for connection of standard AHD-VC cameras to video distribution and control unit AHD-VDCU by means of a CAT5 cable. ...
Böning Automationstechnologie GmbH & Co KG

Video Signal Converter for Thermal Image Camera Flir Navigator II The video signal converter AHD-VSC CF is used for connection of a thermal image camera Navigator II from Flir Systems to video distribution ...
Böning Automationstechnologie GmbH & Co KG

Maretron’s CLM100 converts commercially available 4-20mA current loop transducers into digital data so a wide variety of information can be displayed on compatible NMEA 2000® displays. Numerous 4-20mA current loop transducers are supported ...

Voltage: 12, 24 V
Multifunction programmable converter provided with four analog inputs and one CAN Bus communication port. Can be used to acquire and convert analogue signals from different measure sensors to J1939 compatible ...
San Giorgio S.E.I.N. s.r.l.

Converter developed for Fuel level sensors with 10-180Ω calibration and NMEA2000 output in 57 x 55 x 28 mm case. Available with level sensor cable of lenght L=1m Input: VDO level sensor (Cable gland) _____________________________________________ ...
San Giorgio S.E.I.N. s.r.l.

Double CAN Bus J1939 engine NMEA2000 output converter. Read the main parameters from two ECU engines and convert them into NMEA2000 output to connect last generation plotters and/or integrated navigation systems. Dimensions: ...
San Giorgio S.E.I.N. s.r.l.

Voltage: 12 V
Video Signal Converter Convert analog and digital video signals directly to the desired monitor signal, without any delay or interference. - TVI/AHD/CVI/CVBS (input) to CVBS/VGA/HDMI (output) ...

Voltage: 5 V

The analog-to-digital converter is based on the basis of the STIF A2D8 module. The analog input value is converted into a serial NMEA signal and galvanically isolated from the output of the module.

Voltage: 24 V
VL-N2A is a converter for converting information from NMEA telegrams into analog current or voltage signals. The data is exchanged via the serial port type RS422. All received NMEA messages are given ...

Voltage: 24 V
The converter consists of 3-phase synchro signals in the NMEA Standard HDT. The inputs with the jumpers can be adjusted to the present signal voltages. The ratio must be 1:1.

Voltage: 10 V - 36 V
ADPC-101 is designed to digitize the analog signals of the obsolete gyro compasses and logs into NMEA format and transmit that data to the relevant navigation equipment.

Our SDC2000 is an analog and digital signal to NMEA2000® protocol converter. This product allows the connection between marine engine sensors and the boat’s communication network, monitoring the marine ...
Your suggestions for improvement:
Receive regular updates on this section.
Please specify:
Help us improve:
remaining