{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
In-Line Non-return Valve Designed to install in-line Maintains prime in a suction or discharge line Easy to maintain and clean without use of tools
Designed for installation in waste discharge and bilge pump-out systems. Allows waste to be pumped directly into holding tank or diverted to another discharge. 1½" Inner diameter, 1" Straight
The check valve is designed for the maritime climate and prevents water backflow or depletion.Dometic's engineers always test products to cover every possibility. The Dometic OdorSafe ADAPT-CV check valve ...
... Support See below for a full list of accessories Diverter Valves Allow you to divert flow to overboard or deck pump out DV5630 Diverter Valve 1" (25mm) connections DV5606 Diverter valve ...
Whale
... station steering is required, then it is necessary to install this block, or to use two steering pumps with built in non-return valves (type HTPR).
If a change-over to tiller steering is required an installation of a by-pass valve is necessary.
Fuel cut-off solenoid valves for inboard engine boats, which meet RINA regulations, incorporating a hand release knob to open the valve manually in case of electrical failure, complete ...
Electric valve for fresh water on boats. ¼” ports. Maximum pressure 5 Bar. Brass body, stainless steel internal sleeve. Man applications: wiper systems and water distribution on boats.
Outlet Ventilation Valve To install on a siphon break (not provided) to avoid risks of siphoning effect on long piping system with no direct gravity. To install over the outlet waste water pipe, pipes of O.D. 1.5″ ...
Inlet Ventilation Valve Inlet ventilation valve siphon break to install on a siphon break (not provided) to prevent raw water back flows with special installation scenarios. To install over the inlet ...
Forespa® MF 850 series of Ball Valves are precision molded in high strength Marelon®. Their great strength, light weight, and complete freedom from corrosion and electrolysis make them the ideal valve ...
Ball valve for sea-water circuit Code Inches WP519723 1/2" WP519724 3/4" WP519725 1"
... equipment By-pass valves are used as additional equipment, and they are necessary for a quick change-over from hydraulic to manual steering on vessels where regulations prescribe it. They are installed on smaller sailing ...
SCAM-Marine d.o.o.
... equipment By-pass valves are used as additional equipment, and they are necessary for a quick change-over from hydraulic to manual steering on vessels where regulations prescribe it. They are installed on smaller sailing ...
SCAM-Marine d.o.o.
... multiple steering position systems. Description Dual non-return valve is additionally installed into systems with more steering positions (if pumps are without non-return valve), and its function ...
SCAM-Marine d.o.o.
... sectional valves are a standard in winch applications across the marine industry. There are control options for either rotary lever or by-pass flow control in conjunction with excellent spool metering ...
RV60D Direct Acting G1/2 Relief Valve 60 lpm CODE:RV60D G1/2 The 60 l/min relief valve is a direct acting cartridge valve. It is used in a range of inline mounted manifolds with ...
Female-female ball valve used to close sea water circuit for air conditioner maintenance or when the operation of the air conditioner itself is not required. Available in three sizes, 1/2", 3/4", 1".
Name: stainless steel boat valves Size: 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" Surface: mirror polishing
Where pressurised fresh water is available an electrovalve can be used to control the washer unit feed. Available voltage: 12V - 24V DC 220V AC Threaded part for the connection: 1/8 G
Seacock - Ball Valve Design Product Description Cast Bronze 90° Curved Hose Adapter Includes Thru-Hull, Hose Adapter, Drain Plug, Four Pre-Drilled Mounting Holes and Bonding Screw. PERKO Seacocks ...
Designed and made in New Zealand for use in marine applications above and below the waterline, our Ball Valves are IMCI and Bureau Veritas approved to ISO standard 9093-2, and are ideal for controlling ...
Tru Design Plastics Ltd.
... OEM Select fuel components. Constructed of brass, these Moeller must-have valves meet ABYC H-24 requirements and provide ant-siphon protection. Choose Moeller for all your fuel valve needs
Non return valve prevents toilet and bilge system against flooding. Hose connection 38 mm.
04378-2 // 04378-3 NO RETURN WATER VALVE Made of polypropylene.
Eval
... GROCO patented SBV Series Seacocks allows for instant emergency bilge pumping, a simplified winterization process, and convenient cooling system flushing. IN AN EMERGENCY: While the connected engine is running, close ...
Groco
The Leafield A5 valve is the valve fitted to the Tinker range of boats.
Wing & Henshaw inflatable Solutions
Inline check valve to reduce back pressure and facilitate pumping. Fits Beckson FH-1-1/2 or VCS-1-1/2 Hose
INFLAT ION - DEFLAT ION VALVES New inflation – deflation valves. Height and diameter are very compact. The linkage string has been replaced from a seal system that remains under the closing cap. Available ...
CEREDI
... connections diverse valve type and number, as to fit the control valve panel to your hydraulic system. Up to 18 lpm flow for best working (?p 3 bar). Black line: Cariboni-Caritec standard manual valve ...
Please specify:
Help us improve:
remaining