|
|
Aqua Boat lights constructs our poly-carbonate housing to delivers a solid underwater illumination solution for your night time marine-life viewing.
BEST MOUNTING SURFACE: Any surface
REPLACING BULB: Can be done from within vessel
BULBS USED: (6) White 5-watt LED's
LUMENS: 900
LENS TYPE: Optics
CONSTRUCTION: Poly-carbonate housing with bronze mounting hardware and aluminum insert
POWER SUPPLY: 12 to 24 volts DC 5 Amp
INSTALLATION:
6" to 48" below water line (Lenses tested to a depth of 300ft) Spacing between lights is 6ft to 8ft |
|
Aqua Lights for boats' bronze shines like gold and will never corrode!
Aqua Lights are sure to illuminate your water and the fish that surround you. Aqua Lights is your best source for premium marine underwater lights at deeply discounted prices!
Aqua Lights utilizes an all naval bronze housing that delivers a solid underwater illumination solution for your night time marine-life viewing.
BEST MOUNTING SURFACE: Fiberglass hull
REPLACING BULB:
Can be done from within vessel
UPGRADE TO:
35 Watt Xenon, 50 Watt Xenon,
75 Watt Halogen
BULBS USED:
(6) Green 5-Watt LED's
LUMENS:
900
LIGHT LIFE:
Approximately 20,000 hours
LENS TYPE:
Borosilicate glass lens is 0.6"/15mm
HOUSING:
Naval bronze
POWER SUPPLY:
12 volts running current 1 AMP/24 volts running current .5 AMP's
INSTALLATION:
6" to 48" below water line
(Lenses tested to a depth of 300ft)
Spacing between lights is 6ft to 8ft |
|
Armstrong Thru-Hull Lights for boats are designed to enhance the boating experience of fishermen and divers. Available for both flush mount and surface mount applications. Utilizing a durable and simple, direct-wired fixture, Armstrong Lights are powered by 12/24 volt DC with no transformer needed and are easy to install.
Additional Features…
• Illuminate diving area to depths of 25 feet
• Attract bait fish
• No reflection – lights are submerged in normal use
• 50 watt Halogen
• 45,300 lux
• 2,000 hr boat lamp life
• Bulb easily accessible either internally or externally
|
|
OceanLED is proud to announce the release of the long awaited Fish Strobe Series taking you to the next level of sailboat fishing.
The FS Series strobe light for boats features a choice of 9 strobe patterns controlled by a panel for boats mounted withc. Choose from a rapid to a slow strobe pattern to intermittent flashes to elongated bursts. Used both in the day and night, the Fish Strobe works in a similar manner to how fish reflect sunlight, however The Strobe has a controllable flash pattern and is incredibly more intense.
Utilizing Tritonium Optical lenses and supplied with a quick connect system by Deutsch ensuring an easy installation that complies with ABYC, E11 regulations.
Approved by Lloyds register, RINA, ABS PDA, NMMA Ignition Protection.
Available in 2 sizes, the FS - Series 1 and the FS Series 2 with either Super Blue or Super Green LEDs.
The depth of the water, the type of fish, the time of day or night and the strobe pattern will all play into the thrill of the hunt.
|
|
The Flush Mount from OceanLED has an exceptionally low profile giving it virtually unlimited Hull Mounting options. This light can be retro-fitted into most existing underwater lighting for boat hole cut outs, offering immediate benefits of no Startup power surge, low heat, minimal maintenance and improved light output.
Suitable for Fiberglass, GRP and wooden hulls and now also for use on aluminium/steel hulls using the delrin sleeve.
Low profile bezel offering almost unlimited mounting possibilities.
Lloyds Type Approved, RINA, ABS Type Approved, USCG Ignition Protected and ABYC H-27 Side Load approved.
All lights for boats utilize Tritonium Optical lenses, and are supplied with a quick connect system by Deutsch ensuring almost 'fool proof' installation and compliance with ABYC, E11 regulations.
Available in 1520, 2010 & 3010 Series with Super White LEDs, Super Blue LEDs and the Super Green LEDs. |
|
Low cost - not low quality – LED underwater lighting for boats from the industry leader.
Amphibians are the worlds first lighting collection designed to be used in or out of water. This new tough range was created firstly to satisfy the increasing demand for - high quality, - low cost - underwater lighting for smaller craft and secondly to counter the growing imports of cheap and ineffective LED underwater lighting, as we have always believed that the bitterness of poor quality remains long after the sweetness of low price.
All Amphibians utilize the latest ultra high output LED’s, have internal drivers for 12 or 12/24vDC usage, require a very low power draw with no start-up current and need a mere 8mm (5/16th) hole cut out for the cable. Utilizing unique OceanLED tritonium lensing with high tech injection moulded polymer casings resistant to all known solvents and adhesives, Amphibians are quick and simple to fit and are covered by OceanLED’s 2 year warranty. The Amphibians are exceptionally easy to install and can be used anywhere, such as;
• Transoms
• Engine for boat Brackets
• Under the gunnels
• Trim tabs
• T-Tops
• Boat trailers for boats for night launching.
• ROVs
• Tail gates
The A3 is now readily available in the USA, and other parts of the world (check with your local representative for details.
The A6 and A12 have an expected delivery date of Mid June. Keep checking website for details. |
|
The most powerful marine underwater light available is from OceanLED - the NEW 4010 Super Nova lives up to its name.
At twice the power of a 3010, the 4010 Super Nova is a hybride of the ever popular 1" Thru Hull. Utilizing a slightly larger hole cut out at 1 1/2" the 4010 Super Nova offers the largest light output of any underwater light available on the market, and is a landmark in LED technology.
If you want the best and the biggest underwater light - then the 4010 Super Nova is it.
Suitable for Fiberglass, GRP and wooden hulls and also for use on aluminium/steel hulls using the delrin sleeve.
All boat lights utilize Tritonium Optical lenses, and are supplied with a quick connect system by Deutsch ensuring almost 'fool proof' installation and compliance with ABYC, E11 regulations.
Available with Super White LEDs, Super Blue LEDs and the Super Green LEDs.
Currently under going full Lloyds Type Approval. |
|
The revolutionary new retro-fit surface mount boat underwater light provides possible installation without the need for haul out with no hole penetration below the waterline.
Often there are areas on a vessel which make it impossible to install a thru hull fitting, such as frames, marine fuel tanks, etc. The Surface Mount attaches simply to the outer surface of the hull and the power cable enters the hull above the waterline, which then allows even spacing of marine lights as a combination of Thru Hull or Flush Mount lights can be used alongside a Surface Mount as all LEDs and colors are identical, its only the mounting style/method that alters.
Internally bonded, with custom overmolded cable entry and uses salt water proof cabling.
Beware of cheap immitations of this style of light.
Suitable for Fiberglass, GRP, wooden and aluminium/steel hulls.
Lloyds Type Approved, RINA, ABS Type Approved, USCG Ignition Protected.
All lights utilize Tritonium Optical lenses, and are supplied with a quick connect system by Deutsch ensuring almost 'fool proof' installation and compliance with ABYC, E11 regulations.
Available in 1010, 1520, 2010 & 3010 Series with Super White LEDs, Super Blue LEDs and the Super Green LEDs.
|
|
The original Thru-Hull with the worlds smallest hole cut-out for a thru hull light at only 1"! This light with a 30mm profile head makes it ideal for Transom mount applications. A very quick to fit and effective marine underwater light.
Suitable for Fiberglass, GRP and wooden hulls and now also available for use on aluminium/steel hulls using the delrin sleeve.
Lloyds Type Approved, RINA, ABS Type Approved, USCG Ignition Protected and ABYC H-27 Side Load approved.
All lights for boats utilize Tritonium Optical lenses, and are supplied with a quick connect system by Deutsch ensuring almost 'fool proof' installation and compliance with ABYC, E11 regulations.
Available in 1010, 1520, 2010 & 3010 Series with Super White LEDs, Super Blue LEDs and the Super Green LEDs. |
|
| The UL Ti MATE 80 20 watt LED is available in 12 or 24 volt. |
|
The Original.
AQUALUMA Underwater Lighting for boat 3 series was designed with long life in mind. The corrosion proof, injection molded polycarbonate housing that is the signature of all the AQUALUMA range was first created for the 3 series.
Available in a range of 3 colours, Blue, Green or White, all are supplied with sealant, 3.7 metres of cable, carry a two year warranty and if necessary can be serviced from inside the boat.
Make your boating experience all that more illuminating and install an AQUALUMA Marine underwater light today. |
|
Following on from the huge worldwide demand of the AQL 3 series, AQUALUMA releases the 6 series.
This new larger option has been designed in response to the large number of requests from the world's super yacht industry who have very quickly grasped the obvious advantages of the AQUALUMA products.
The AQL 6 series is available in the three colours Blue, White and Green.
The construction is the same as the proven AQL 3 series, corrosion proof, injection molded polycarbonate, internally driven and maintained.
What more can any boat owner want BUT the Tri Colour ... |
|
Aqualuma 1 Series - The Aqualuma Advantage
-2 Unit Set.
-Master, Slave & Driver Set
-Wide angle elliptical beam 12° x 50°
-No Lens seal to leak
-Very low DC power consumption
-Draws less than 0.5 of an amp per light @ 12 volts
-Very low heat emission
-Can be operated out of the water
-Long life, high output LED light engine for boats
-High impact resistant polycarbonate housing
-No bonding to anodes required (Housing cannot corrode)
-Light engine will accept 12 volt DC power source
-Serviceable from inside the boat
-Available in white, blue or green
-Cabling to suit for boat your application : IP68 marine connectors Master to Slave, your loom to Master
-Ignition Protected
-5 year Warranty
-Australian designed and manufactured
-Easy install = low installation cost
-*Aqualuma Sealant Supplied |
|
| The Xenon Thru-Hull SeaLite® is an extremely rugged system with unmatched light output. The low voltage (8-32V), 35-Watt gas discharge light produces intense white light for maximum penetration in seawater, and was engineered specifically to be a competitively priced, yet superior Xenon light. As with all of DeepSea's Thru-Hull SeaLites®, the Xenon-S comes standard with unique features that set it above all other thru-hull boat lights on the market. The sapphire crystal port is used for its strength and thermal characteristics. DeepSea is the only thru-hull light company to offer this highly durable, scratch resistant material. |
|
| For decades DeepSea Power & Light has been designing innovative underwater products that exceed industry standards. The new LED Thru-Hull SeaLite® is the next evolution of the proven Thru-Hull SeaLite® design. Several features come together in the LED Thru-Hull SeaLite® to create a light that offers amazing light output, is extremely rugged and most importantly, safe. There are 18 high color temperature LEDs, each with its own reflector to distribute the light for maximum effect. Thermal compensation circuitry regulates the temperature of the LEDs, improving the life of the LEDs and allowing the light to be run in air. |
|
The HID Thru-Hull SeaLite® is an extremely rugged system with unmatched light output. The fully sealed light head, scratch resistant sapphire port and precision-machined housing ensure that the system will remain reliable, even in the harshest environments. Each version utilizes the same thru-hull fitting and boat lamp, but offers ballast options to suit for boat various
installations and budgets. |
|
| DeepSea Power & Light's line of Thru-Hull SeaLite® products set the standard for durability and performance. This extensive expertise was used to design the Halogen Thru-Hull SeaLite®. As with all of DeepSea's Thru-Hull SeaLites®, the Halogen comes standard with unique features that set it above all other thru-hull marine lights on the market. The sapphire crystal port is used for its strength and thermal characteristics. DeepSea is the only thru-hull light company to offer this highly durable, scratch resistant material. |
|
| For decades DeepSea Power & Light has been designing innovative underwater products that exceed industry standards. The MiniLED Thru-Hull SeaLite® was engineered to fill a need for a powerful, rugged light, in a compact package. Utilizing the latest in high brightness LED technology, the MiniLED Thru-Hull SeaLite® provides incredible light output for its size. The MiniLED Thru-Hull SeaLite® is ideal for marine center console boats, where space is at a premium, and price is an important consideration. All electronics are integrated in the watertight housing, providing protection and simplifying installation. |
|
Aqua Boat lights are sure to illuminate your water and the fish that surround you. Aqua Lights is your best source for premium marine underwater lights at deeply discounted prices!
BULB USED: 175-watt metal halide bulb
LUMENS: 27,000
LIGHT LIFE: Approximately 6000+ hours
REPLACING BULB: Can be installed from inside your vessel
LENS TYPE: Borosilicate glass lens is 0.5" thick
HOUSING: Aluminum
POWER SUPPLY: Dual ballast 120 (1 phase); 240 (1 phase); 280 (3 phase) volt, Running current 1.5-0.75 amps
CABLING: Length of cable for boat to ballast must not exceed 40ft 15ft supplied; Custom length available
INSTALLATION:
12" to 48" below water line
(Lenses tested to a depth of 300ft)
Spacing between lights is 5ft to 8ft |
|
Aqua Lights for boats are sure to illuminate your water and the fish that surround you. Aqua Lights is your best source for premium marine underwater lights at deeply discounted prices!
BEST MOUNTING SURFACE: Weld-in Aluminum
REPLACING BULB: Can be done from within vessel
BULB USED: 75 watt Halogen bulb
LUMENS: 1,250
LIGHT LIFE: Approximately 6000+ hours
LENS TYPE: Borosilicate glass lens is 0.4"/10mm
HOUSING: Aluminum
INSTALLATION:
6" to 48" below water line
(Lenses tested to a depth of 300ft)
Spacing between lights is 6ft to 8ft |
|
REPLACING BULB: Can be done from within vessel
BULB USED: 600-watt Metal Halide
LUMENS: 160,000
LIGHT LIFE: Approximately 6000+ hours
LENS TYPE: Borosilicate glass lens is 0.6"/15mm
HOUSING: Aluminum
POWER SUPPLY:
Our light is 12 volt start up current 18 amp for about 25 second & 3.5 amps continuous
INSTALLATION:
6" to 48" below water line
(Lenses tested to a depth of 300ft)
Spacing between lights for boats is 6ft to 8ft |
|
The Sea Vision SV14 weld in model for aluminum hulls can be installed in the transom or the hull, it utilizes a 150 watt metal halide sailboat lamp and 110 or 230 volt AC power. The boat lights can be welded at adjustable angles to boat suit all hull shapes. The hull shape and positioning will dictate the angle of the light you require, angles available are 0-50 degree. All angle options are available on request.
|
|
The UL Ti MATE 75 SA 'Super Adjustable' (patent pending) weldin from Underwater Boat lights LIMITED ™ for aluminum and steel hulls can be installed in the transom or the hull. The SA reflector unit allows a change in beam direction of up to 20 degrees. This is available with either a 150 or 250 watt metal halide sailboat lamp with a 110-230 volt ELECTRONIC ballast, perfect for DC power on a yatch with either and aluminium or steel hull. A 30 and 50 degree angle is also available in both materials.
S00330 - 75 - SA - UL Ti MATE 75 SA 30 Degree Stainless Steel
S00350 - 75 - SA - UL Ti MATE 75 SA 50 Degree Stainless Steel
S00630 - 75 - SA - UL Ti MATE 75 SA 30 Degree 5083 Aluminium
S00650 - 75 - SA - UL Ti MATE 75 SA 50 Degree 5083 Aluminium
|
|
The latest entry level LED marine underwater light for boats under 25'.
Made from a solid synthetic material resulting no corrosion and a strong compact unit.
We do not use plastic or polycarbonate lenses as whilst they do offer great strength they will cloud overtime in salt water and can be very easily scratched, which drastically diminishes light output. This is why even our entry level light utilizes the revolutionary Tritonium Optical Lensing system.
At a total of 10w in power and available in a variety of colors, this light not only delivers a significant light output for its size but is at the cutting edge of LED technology.
USCG Ignition Protected and ABYC H-27 Side Load approved. |
|
The Sea Vision SV16 model utilizes a halogen marine lamp with 12 or 24 volt DC power and can be installed in the transom or the hull. Generally it should be installed in smaller boats and for the occasional light user.
|
|
Docks for boats, pilings, marinas, waterside restaurants and boat houses can now experience the underwater lighting for boats phenomenon with our DV24 dock light. The light has a PVC housing with a 100 watt halogen sailboat lamp and is available in 12 volt a.c./d.c. The reflector is a 45 degree wide angle for maximum light output. The dock light is fastened to a flat surface by way of two mounting brackets. The light is fully submersible and IP68 rated.
|
|
The triple LED dock for boat light (Ref. S40351) uses three 3 watt LED’s. The light is IP 68.
If this light is to be used underwater, the driver required is S41105 for each individual light.
If this light is to be used above water, the driver required is S41104 for every 2 lights for boats.
|
|
Brand new lighting for boat technology has allowed us to introduce the Sea Vision SV19 model. This utilizes a 50 watt xenon marine lamp and 50 watt ballast. This is the first of its kind to incorporate the ballast and ignitor built directly into the thru-hull casing. It is the brightest 12 volt DC light available. Can be installed on small to mid size boats including sportfishers and cruisers.
|
|
BEST MOUNTING SURFACE:
Fiberglass hull
REPLACING BULB:
Can be done from within vessel
BULB USED:
75 watt halogen bulb
LUMENS:
1,250
LIGHT LIFE:
Approximately 600+ hours
LENS TYPE:
Borosilicate glass lens is 0.4"/10mm
HOUSING:
Naval bronze
POWER SUPPLY:
12 volt running current 7 amps/ 24 volt running current 3 amps
INSTALLATION:
6" to 48" below water line
(Lenses tested to a depth of 300ft)
Spacing between marine lights is 6ft to 8ft
|
|
|
Underwater lighting
