|
|
|
PINS BETA STAINLESS A2 (9203)
|
|
Beta pins (bichromate galvanized steel & stainless steel AISI 316L)
Double beta pins (bichromate galvanized steel)
Safety beta pins (bichromate galvanized steel)
use in industrial supplies, DIY, entertainment industry, agriculture
|
|
By adjusting the backstay tension, you can increase your boat speed and point higher. Holmatro integral adjusters enable you to alter the backstay tension accurately and quickly. Holmatro backstay adjusters are made of lightweight aluminium and have the only two-speed integrated pump.
- Integrated single-speed pump
A single-speed pump means compact design and easy to reach maximum tension.
- Lightweight
Advanced design techniques and materials keep the weight to a minimum.
- Luminant pressure gauge
Makes reading the pressure gauge easy, even in the dark.
- Various colour options
Standard clear anodized aluminium finish. Black anodized or other colours optional.
|
|
|
Ergonomics meets economics. The new Series 8 Integral Backstay Adjuster incorporates several key design improvements. The pressure gauge is positioned prominently, enabling fast, accurate reading of tension values. A longer pump handle produces faster pumping motion and more tension per stroke, which delivers greater performance out of modern masts. The feed tube is seated into the contour of the cylinder, resulting in a more secure design and integrated look. And its cost has remained highly competitive. In testing, the Navtec Series 8 Integral enabled sailors to increase rigging tension quickly, precisely, and easily. With each stroke of the handle, rake increased along with forestay tension, resulting in improved roller furling gear performance, sail shape, windward performance, and speed. Use of the specifically designed Integral toggle is strongly recommended.
|
|
Holmatro hydraulic cylinders are suitable for many applications on board, from tensioning backstays and forestays to controlling outhauls and travellers. A cylinder in combination with a control panel allows accurate and quick adjustment. Advanced design techniques and materials keep weight to a minimum.
HCL-10 Cylinder
Holmatro hydraulic cylinders are suitable for any tensioning application on board, from tensioning backstays and forestays to outhauls and travelers. A cylinder in combination with a Holmatro control panel allows for accurate and quick adjusting of your rigging tension.
|
|
For wire sizes 7/32" - 1/2"
|
|
Linchpins for pipes (bichromate galvanized steel)
Linchpins (galvanized & stainless steel AISI 316L)
Safety linchpins (bichromate galvanized steel)
use in industrial supplies, DIY, entertainment industry, agriculture
|
|
Fully dropforged product with high quality stainless steel
Outstanding working and breaking loads
For any kind of fastening applications (shrouds, lilfelines, blocks...)
Delivered with bolts and counterplate
Max tightening torque : 2.3 Nm
|
|
|
U-Bolts All Stainless steel engineered construction complete with top plate, nuts and washers, supplied as standard. Collars on the shanks of the bolt whilst adding to the appearance also allows the nuts to be fully hardened up and help dissipate water seepage. For stronger anchorage points, we advise the additional stainless steel backing plates. The popular economy range of 'U' bolts are manufactured from Stainless Steel type 304 and have crimped ears.
|
|
Selden backstay tensioners have smooth, clean surfaces. Even the wire terminal is fully covered. These low-weight backstay tensioners are simple to use. All you do is insert a standard winch handle and turn. The tensioner has a maximum working load of 30 kN. The stroke is an ample 250 or 400 mm, depending on the length of the tensioner.
|
|
BACKSTAY TENSIONER BLOCK
Suitable for use on split or twin backstays, just attach block system to lower clevis pin. Available for 2 sizes of backstay wire 5mm and 10mm.
|
|
Stay Adjusters allow wire rigging systems to be altered by means of a clevis pin. All models constructed from stainless steel strip with different sizes and spacings.
The fine tune adjuster R4394 is a must for hotshot dinghy crews. Pivoting foot utilising three holes always gives a straight line between shroud and full anchorage point, plus a fine 2mm adjustment.
R4392 Shroud "SPINI" roller acts as guide for sheet when reaching. Fits all RWO shroud adjusters with 5mm, (3/16in.) holes.
Shroud Levers improve downwind performance by allowing the mast to lean forward and permitting the boom to be squared off. Another use of the lever is to instantly slacken the tension in standing rigging; both on boats and hang gliders. Two models are available, both having an easy to grip handle and adjustable throw. Both levers are strong enough for sailboats up to 5.9m. (18ft.) long and can be safely used in winds up to 20 knots.
|
|
PI1Series
Clevis Pins PI1 Series secures the mating part in the fork fitting.
|
|
Replacement pin for Sta-lok Fork reference, 134
|
|
|
Offers the highest strength and lowest weight in terminal bodies and reducers. Low-weight, high-strength anodized aluminum bodies are used to mate with high modulus Aramid Fiber Cable. Titanium options are also available. End fittings are made from 316 stainless.
|
|
The toggle (D530) screws on to the cylinder piston rod for small length adjustments, not to be tensioned under load.
|
|
Sta-lok offer an extensive range of stainless steel turnbuckles to suit every application. Manufactured from high quality certificated materials the Sta-lok range is unparalleled.
Threaded Bronze Inserts permanently locked in each end ensure superb adjustment without seizing or galling.
|
|
|
The Blue Wave Eye Terminals all features, engraved wire size, Blue Wave logo, and swage depth marking for faster and easier swaging.
|
|
|
Our swage terminals are crafted from 316 stainless for maximum corrosion resistance and are used to terminate 1x19 stainless steel wire, flexible wire rope, and Dyform wire. Navtec swage terminals are available in many sizes to answer practically any problem.
|
|
|
Terminals are an effective and neat way of finishing wire with an eye or fork end. They are manufactured from Type 316 stainless steel to a high precision standard. The swage terminal requires compressing onto the wire with the use of a roll swaging machine whilst the swageless terminals can be fitted with the use of a spanner. Terminals are manufactured to suit metric wire only.
|
|
|
The MS20668 Eye End Fittings are manufactured from stainless steel in accordance with the requirements of MIL-DTL-781 and are certified to those standards. Loos Cableware® Division offers a full line of the MS20668 Eye End Fittings and is a QPL manufacturer of these parts.
|
|
|
|
Marine hardware : Rigging screws, Terminals, U-bolts
