|
|
Genuine Sherwood Impellers can be identified using their overall dimensions.
8000K - width 3/4" diameter 1-9/16"
09000K - width 7/8" diameter 2-7/16"
09959K - width 1-1/4" diameter 2-7/16"
10077K - width 25/32" diameter 2-1/4"
10615K - width 1-5/8" diameter 2-9/16"
15000K - width 2" diamter 2-9/16"
17000K - width 2-7/8" diameter 3-5/16" (keyed shaft)
18000K - width 4" diameter 3-3/4"
22000K - width 4-5/16" diameter 4-1/2"
26000K - width 3-1/8" diameter 3-3/4"
27000K - width 2-7/8" diameter 3-5/16" (splined shaft) |
|
As you know, Flexible impellers are the most important part in Flexible impeller pumps.
We improve the impeller performance by special surface coating, decreasing wear and tear so the impellers can last for long time. We recommended you should change the impeller every year. We can guarantee that you will have great satisfaction with JMP flexible impellers. |
|
Impeller removal has been made easier with the patented Sherwood Impeller Puller. Simply thread the puller into the threaded end of select Sherwood impellers and the bolt presses on the shaft, pushing the impeller out of the pump.
Sherwood's Impeller Puller is utilized on five different impeller sizes. Impeller puller 23631 is used on the 17000, 18000, 22000, and 27000 impellers. Impeller puller 24412 is used on the 27000 impeller. |
|
| Flexible impeller pumps make excellent bilge pumps, principally because of their ability to handle bilge debris without damage. Because of the robust design many owners still use our 12 Volt dc or 24 Volt dc flexible impeller motor pump units that are up to 25 years old! Flexible Impeller Pumps also give the benefits of good flow, low cost, low size and weight, and are easily serviced and maintained. Most Flexible Impeller pumps must not be run dry, as this will damage the impeller which will require replacing. However, the Utility Puppy 2000 and 3000 both allow maximum of ten minutes dry running after initial prime. As with submersible pumps, flexible impeller pumps can be operated using a float or Hydro Air switch, and remotely controlled from outside the bilge compartment. There is a wide range of flexible impeller pumps to choose from giving a range of flows, discharge heads, and self-priming options for a wide variety of applications such as ballast transfer, bait tank circulation, and deck wash duties |
|
Flexi pumps have many applications, including:
• Emptying/filling water, oil or diesel.
• Bilge pumping
• Water circulation
The pumps can be combined with a vacuum switch that extends the life of the pump by saving battery capacity and preventing dry running. The pumps are self-priming and give full flow right from the start.
FDC900
Suitable pump for handling water, oil and diesel. Can be used as a bilge pump, flushing pump and for water
circulation on board.
FDC2700
Flushing, bilge and water circulation pump which is also highly suitable for handling water, oil and diesel. The mo-tor is rated for continuous operation at up to 1.2 bar (17 PSI) pressure.
|
|
Ideal for Two Engine Service - Either Two Engine, Engine / Generator or Diesel Engine / Transmission combination on Inboard sailboat or power boat applications
Two way shut off Brass valve with adapters for 1/2" ID hose installation
Mounting plate for easy engine room installation
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps water, oil and diesel fuel
Built in fuse for motor protection |
|
Ideal for portable use on Outboards, Stern Drives, or 4 Stroke PWC's or can be Permanently Installed
4' Dipstick & Drain Tubing
8' Power Cords with Alligator Clips
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps oil, diesel or water
Built in fuse for motor protection |
|
Ideal for single inboard/outboard sailboat or powerboat application
Single shut off Brass valve with adapters for 1/2" ID hose installation
Mounting plate for easy engine room installation
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps water, oil and diesel fuel
Built in fuse for motor protection |
|
Ideal for portable use or can be permanently installed
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps oil, diesel or water
Built in fuse for motor protection |
|
| The RHEINSTROM Impellerpumpe IP 50 can be used for the promotion of drinking water or waste water. The parts coming with water into contact are made of stainless material. The pump is positioninsensitive. It is sucking in drying. A longer unlubricated operation should be avoided however, since otherwise the Impeller could suffer damage. The pump is available in 12 V and 24V execution. |
|
| ... products without information |
| |
|
|
see the results for the following category