- Equipment >
- Propulsion, Engine controls >
- Boat bearing
Boat bearings
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
Plain Roller upper bearing Manufactured in 6082 aluminium and anodised Precision Delrin rollers Low friction co-efficient and easy to install flanged housing Specifications For rudder stock dimensionMaximum ...
Lewmar
Manufactured in 6082 aluminium and anodised Bearing includes self aligning ball and precision Delrin rollers Easy to install flanged housing and no grease or maintenance required. Specifications For rudder stock diameter 50mm
Lewmar
Aluminium Roller Bearing Manufactured in 6082 aluminium and anodised Accepts sealing system for lip seals or rudder tube and gaitor Low friction co-efficient Available in self-aligning version
Lewmar
The input can be directly coupled with our flexible coupling FC type.
Reggiani Nautica
Rudder guide bearings with fittings for shaft d. 30-40-50mm.
Reggiani Nautica
Head LS type with thrust bearing Thrust bearing group with flexible joints
Reggiani Nautica
This mounting is used when there is no need for an intermediate bearing between the bracket and the coupling. The system includes an epoxy tube to be resined available in two standard lengths, the customer can adjust ...
This type of bearing in diametrical parting is very easy to assemble, its design and implementation have been simplified to allow installation at lower cost. The body is in grey cast iron and has a good rigidity. These ...
... type of thrust bearing resists to strong axial thrusts. It includes a rolling bearing to support radial loads and a thrust bearing to absorb the axial loads. It is possible to mount ...
Astern head INOX with rubber bearing consists of INOX housing with nut and flange to fix it to the boat hull. Inside the housing is a liner with hexagon rubber sleeve to enable water circulation between ...
The Tides Marine Upper Rudder Bearing-Low Profile (URB-LP) is designed to be installed on vessels where the steering system components need to be located as close to the rudder shelf as possible. Mounted ...
Tides Marine
The bearing bushing is a brass structure that supports the bearing and is threaded to the stern tube, it is placed outside of the hull of the boat. Seawater lubricated, with a conduit ...
... system. Lower bearings havent got a flange and they have to be glued (from outside) in a rudder tube long enough above the DWL. The bearings are provide of bolts to fix them to the rudder shaft. An adhesive ...
Solimar
... as some imperial sizes (inches). The bearings are supplied as rubber bearings with a range of tubes or as synthetic bearings for use in demanding conditions. Regular replacement ...
... to replace a worn out cutless© bearing in your boat’s stern bearing? RE Thomas Marine Hardware specializes in changing out water lubricated bearings, ...
RE Thomas Marine Hardware
... bottom and supported at the top by a transverse hull. The tube is manufactured from high quality marine grade GRP and is fitted with polyacetal bearings.
Your suggestions for improvement:
A boat bearing is a fitting which supports, aligns and, in some cases, lubricates a rotating shaft. On NauticExpo these fittings are designed for use on leisure craft.
ApplicationsBearings have two primary uses aboard recreational vessels. They support the propeller shaft, either held by exterior support brackets or mounted within the hull, if the shaft is particularly long. They also support and align the rudder tube.
TechnologiesPropeller shaft bearings are usually made of water-resistant polymers and hydrocarbon compounds. The material must be sufficiently dense to ensure durability, but flexible enough to absorb the vibrations of the rotating shaft. Rudder tube bearings are metal tubes lubricated by seawater or grease. They are sometimes mounted on ball bearings. Various diameters are available.
How to chooseChoice will depend on precise use, tube diameter and mounting mode (e.g., exterior support bracket). Installing metal bearings on an aluminum hull requires measures to prevent electroysis.
Receive regular updates on this section.
Please refer to our Privacy Policy for details on how NauticExpo processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- AboutVirtualExpo Group
Please specify:
Help us improve:
remaining