|
|
Gobius 4WF - For water- or diesel marine tanks in stainless steel, steel, plastic and aluminium
All Gobius products measure from the outside, avoiding the need of to take the tank apart and drill unnecessary holes.
- Very easy to use
- Traffc marine lights boat lamps show the current liquid level
- Automatically checking the level
- No extra service is needed
- Extremely low electricity consumption
Gobius is easy to install
On the sensors there are strips of tape that are provided to attach the sensors directly onto the surface of your tank. The panel for boat may be placed in the pentry or at the electric control panel. All necessary cables and plugs needed to connect the sensors and panel with the control unit are included.
Very easy to calibrate
No tanks look the same. There are always differences in e.g. size, construction, thickness and age. In order to compensate for these differences you have to calibrate the tank before you start to use your Gobius. However, the calibration only takes a few seconds, all you need to do is to press a button while the tank is full.
Extremely low electricity consumption, less than 40 mA (12 volts)
Gobius is constructed to minimise electricity consumption and is extremely efficient. Gobius sends power to its sensors in impulses instead of a continuous supply, thus saving your craft’s battery.
Art No 970381 Gobius 4WF for tanks in stainless steel, steel & aluminium
Art No 970193 Gobius 4WF for tanks in plastic |
|
SeeLeveL 709, multi tank monitor system
This system provides an outstanding balance between low cost and full features. Instead of single points that give you only a close appr. of how full your boat tanks are this system offers a continuous level and shows an actual number, in percent of full.
Measures tanks up to 300 mm tall with a single sender or 600 mm tall with dual senders. 3 sender boards for boats are included.
Art No 970213 |
|
SeeLeveL 713, multi tank monitor system
No buttons to push! The level of each tank, plus the outside temperature, is shown individually. 713 provides accurate tank level information in percentage of full. Measures marine tanks up to 430 mm tall with a single sender or 840 mm tall with dual senders. 3 sender boards for boats are included.
Art No 970220 |
|
Gobius 4 for boat holding tanks in stainless steel, steel, plastic & aluminium
Gobius has been developed to meet the demand from those boat owners who want more information, those who not only want to know when the tank is full.
All Gobius products measure from the outside.
-Coloured boat lamps show the current fluid level
-You avoid the struggle with taking the tank apart
-No extra drilling of hole
-No need for extra service
-Extremely low electricity consumption, less than 40 mA
-Good for everybody: boat owners and environment
Gobius is easy to install
On the sensors there are strips of tape that are provided to attach the sensors directly onto the surface of your tank. The panel for boats may be placed in the washroom. All necessary marine cables and plugs needed to connect the sensors and panel with the control unit are included.
Very easy to calibrate
No marine tanks look the same. There are always differences in e.g. size, construction, thickness and age. In order to compensate for these differences you have to calibrate the tank before you start to use your Gobius. However, the calibration only takes a few seconds, all you need to do is to press a button while the tank is empty.
Extremely low electricity consumption, less than 40 mA (12 volts)
Gobius is constructed to minimise electricity consumption and is extremely efficient. Gobius sends power to its sensors in impulses instead of a continuous supply, thus saving your craft's battery for boats.
Art No 970091 Gobius 4RFP for tanks in stainless steel, steel & aluminium
Art No 970053 Gobius 4RFP for tanks in plastic |
|
SeeLeveL 707, multi tank monitor system for plastic tanks for boats
This level gauge has an easy to read LED display. Display fresh, gray, or black tank levels at the press of a button. 9 segmented display gives accuracy to 1/8 (12.5%) of a tank. Orange and red marine indicators are used for low and empty level warnings for the fresh water tank. Orange and red indicators are used for high and full level warnings for the gray and black boat water tanks. 3 sender boards for boats are included.
Art No 970206 |
|
Our programmable fluid level monitors provide reliable and accurate Tank level indication.
There are no moving parts to foul, or electrical components inside the tank. Unaffected by floating solids or stray current, Tank Sentry is the ideal solution for the toughest of fluid level monitoring assignments.
All Tank Sentries operate on 12 to 32 volt DC power. With a few simple adjustments they are capable of monitoring marine tanks from 6 inches to 6 feet deep, right out of the box. All models have 10% incremental LED displays.
All units include a monitor panel for boat, 30 feet per tank of shielded 18/3 wire, 1 SYM-2Q sensor module per tank, 10 feet of urethane tubing per tank, 1 TPA-1250 1-1/4" tank penetration assembly per tank, and 3 heat shrink wire connectors for boats. Installation accessories such as extra wire, mounting flanges, and pump for boats relays are sold separately.
|
|
| Fireboy®-Xintex® has designed a line of liquid level gauges that are built to the quality standards of all our marine equipment. Senders are available for either threaded or flanged top-of-tank installation. Choose either one-tank or two-tank monitors with appropriate threaded or flanged senders. Order online or call our factory at 1-866-350-9500 for Assistance and Technical Information. Not interchangeable with the WTG System Series, which are three-wire connections. (These items have two-wire hook-ups.) |
|
In addition to providing complete management of your vessel's fuel flow and fuel remaining, Navman's Fuel 3100 utilizes speed data from MARINE GPS or paddlewheel input to calculate real-time fuel economy data. The Fuel 3100 can be programmed to display these values in miles per gallon or litre.
This important information allows you to determine the optimum throttle and trim settings for single and twin engine boats. This will save you money on fuel and minimize long-term engine wear by running your engines for boats at their most efficient settings. |
|
You want to stay in complete control of the situation and have accurate information. Guesswork is not good enough when it comes to the status of your power system for boat.
How much longer will my service battery for boats last? What condition is my starter battery in? How much current is being recharged? How long do I have to wait for my battery to be fully recharged? How many charge cycles has my service battery undergone… The answers to all these questions can be provided by Mastervolt’s instrumentation. |
|
| Liquid Crystal Display (LCD) tachometer model 8905. LCD tachometer is backlighted with red LEDs and ideal for use in direct sunlight. Available with or without digital engine for boat hour-meter. Available with polished stainless steel bezel (P) or black anodized aluminum bezel (B). SM & SH versions designed to be used with magnetic sensor or other type of sensor on flywheel, cam gear or similar gear tooth item. SM (Switchable Medium) version can be calibrated to "sense" slide by of 17-90 gear teeth. SH (Switchable High) version can be calibrated to "sense" slide by of 91-255 gear teeth. Standard (non SM or SH Version) used on gas engine or on diesel engine for boats with a mechanical sender. |
|
The TLA100 is used to adapt commercially available resistive tank senders to the NMEA 2000® network. This allows you to observe tank levels anywhere on the vessel where there is an NMEA 2000® compatible display such as the Maretron DSM200.
The TLA100 is compatible with both the American standard (240-33 ohm) and the European standard (10-180 ohm) resistive senders. In fact, the TLA100 can be calibrated for any resistance between 0 and 300 ohms.
Unlike most tank senders that only work with rectangular marine tanks, the TLA100 can be calibrated for irregular tank shapes so you know the true level of the tanks. You can also use the TLA100 with analog gauges so you don't have to get rid of existing gauges to enjoy the advantages of digitally networked information.
|
|
| SENTRY is a cargo tank for boats pressure monitoring system designed in compliance with IMO Regulation 59, providing early warning of under/over pressurisation in tankships. MMS200 intrinsically safe 316SS absolute pressure transducers continually monitor tank pressure and offer excellent durability and long-term stability. The extremely compact M3000 control and alarm system provides indication of the measured pressure in each tank, and generates audio and visual marine alarms. |
|
Water Temp Gauge 100°-250°F
|
|
| ... products without information |
| |
|
|
Tachometers, Fuel gauges...
