|
|
|
Webasto fan-type heat exchangers are available in various ratings and can therefore be matched to any size of cabin. In this way, you can create your own customized comfort zone in each cabin.
|
|
AT model air handlers are draw-through (ducted) units specifically designed for use in marine chilled water systems. Draw-through air handlers can be installed in a locker, under a bunk, or overhead, with conditioned air ducted to a discharge grill placed high in the cabin. Typically each cabin or area has one or more air handlers with an independent climate control to provide the user with the most comfortable environment on the water.
All Dometic air handlers use corrosion-resistant materials, and are fully insulated with deep drain pans to prevent secondary condensation. AT models have an integrated chassis with vibration isolation mounts and a high-performance, rotatable blower.
*Can be used with Cruisair microprocessor or mechanical controls
*Copper tube/aluminum fin water coils are designed for hot/humid marine environment
*Integrated 3-way bypass valve standard
*Sloped drain pan with anti-slosh, antifungal foam
*Includes washable air filter; Micro-particle filters available
*Optional electric heater with 2-stage overload protection
*Optional modulating flow control recommended on large systems to ensure proper water distribution
|
|
Cruisair RE model DX air handlers are draw-through (ducted) units designed to be used with Type R remote condensing units. They are typically installed under a settee or bunk, or in a locker, with air ducted to a discharge grill high in the cabin. They are available in sizes from 4,000 to 36,000 BTU/hr (1.2kW to 10.5kW). Corrosion-resistant materials are used throughout, and the unit is fully insulated to prevent secondary condensation.
*Deep, “positive-flow” drain pan with anti-slosh, anti-fungal liner.
*Copper tube/aluminum fin evaporator coils are designed for hot/humid marine environment.
*Washable air filter included.
*Micro-particle filters available.
*Includes mounting kit with vibration isolators.
*Optional high-velocity blowers on REU models provide increased airflow and lower noise.
|
|
AT-DC model air handlers are draw-through (ducted) units specifically designed for use in marine chilled water systems. The ultra quiet blower has a brushless DC motor that has a wide speed range with virtually no “hum” at low motor speeds. Draw-through air handlers can be installed in a locker, under a bunk, or overhead, with conditioned air ducted to a discharge grill placed high in the cabin.
Typically each cabin or area has one or more air handlers with an independent climate control to provide the user with the most comfortable environment on the water.
*All Dometic air handlers use corrosion-resistant materials, and are fully insulated with deep drain pans to prevent secondary condensation
*AT models have an integrated chassis with vibration isolation mounts and a rotatable blower
*Can be used with Marine Air microprocessor or mechanical controls
*Copper tube/aluminum fin water coils are designed for hot/humid marine environment
*Integrated 3-way bypass valve standard
*Sloped drain pan with anti-slosh, antifungal foam
*Includes washable air filter; Micro-particle filters available
*Optional electric heater with 2-stage overload protection
*Optional modulating flow control recommended on large systems to ensure proper water distribution
|
|
The Glacier Bay Micro Air EP represents the evolution of marine air conditioning into a true environmental control system for yachts.
The Micro Air EP20 (20,000 BTU/hr) systems provide a significant advancement over conventional air conditioning technology. However, to think of them only as air conditioners would sell them short. Micro Air EP systems not only control the temperature and humidity of the air inside the boat, they control the air quality as well.
|
|
E-FD remote evaporators are draw-through, ductable, DX air handlers incorporating variable-speed blowers and integral water-displacing condensate pans. Each unit is pre-charged, test run in all operating modes, and leak checked prior to shipping. E-FD units are ductable and designed to be installed in low cabin areas (under berths, lockers, etc.) and ducted to high supply air grilles.
These units have rotatable blowers providing flexibility to fit specific space requirements and allowing for proper duct work installations. Transition boxes may be used to supply air to more than one area from a single unit.
When choosing the proper model E-FD DX Air Handler, primary consideration should be given to calculated BTU loads and available power supply. A refrigerant line set is required to connect the E-FD to the Marine Air CS condensing unit.
*The unique compact modular design incorporates large plenum chambers for maximum efficiency
*Condensate drain pans are insulated to prevent sweating and have two ½” FPT drain connections
*Quiet, efficient, centrifugal blowers have fully insulated housings
*Large blower inlets provide maximum air flow across evaporator coils
*Charge Guard® protection provides sealed access ports, ensuring environmental protection and system integrity
|
|
EUMM and EMAA are modern, high specification Air Handling Unit ranges with all of the functional sections needed to meet any air handling requirement.
The frame members and solid corner pieces form a sturdy framework.
EUMM is a modular unit offering flexibility of function, size and process while the EMAA is a compact unit based on the same design platform aimed specifically at the needs of the modern cruise liner.
That means we control quality and performance of the entire unit to ensure problem free installation and service.
Some of the main features of our Air handling units:
- Sturdy framework with box-section steel frame members.
- Solid composite material or aluminium, powder-coated corner pieces with no sharp edges.
- 50 mm thick double-skin, flush-fitting panels.
- Non-hygroscopic, rigid sheet, mineral wool insulation with a density of 50 kg/m3.
- Fully enclosed panels.
- Purpose designed coil connection seals.
- Fully dismountable casing.
- Multi-section blocks to reduce site assembly time.
- Corrosion resistant components designed for the maritime environment.
- Stainless steel casing available as a standard alternative.
- Painted casing available as an option.
- Taylor made marine functions.
|
|
The applicable equipment can be found among the widest and most versatile selection of air handling units in the market, air flow volume 0.3 - 45 m³/s.
Future Clean hygiene model is the solution when the air needs to be cleaner than clean.
|
|
MARINE AIR HANDLING UNIT FEATURES
- Insulation thickness 2" or 4"
- Self supporting steel base, ready for deck installation
- Mixing section complete with opposed blade, fresh and return air dampers
- High or medium efficiency filters
- Direct expansion or chilled water cooling coils
- Electric, hot water or steam heating coils
- Electric control panel mounted on the unit complete with all necessary climatic and safety controls
- High performance centrifugal fan enclosed in the units fan section, resiliently mounted with safety screen
|
|
Climaster ZCP
The Climaster ZCP air handling units are flexible and individually designed units primarily for the marine market and for some land applications. Common to all usage areas is the demand for a tough and robust unit capable of meeting very diverse requirements.
|
|
|
HI AIR KOREA air handling unit can establish SINGLE-PIPE AC System, TWIN-PIPE AC system and RE-HEAT AC System (electric reheater or hot water reheater) with the combination of different types of cabin units.
|
|
|
INDEX REFRIGERATION provides lull range of Air handing unit specially designed for marine and offshore application. Unit is made up with modular section that enable us to offer tailor-made to specific vessel and oil drilling unit. Out air handing units come in selection of high/mediums/low pressure units, single/dual duct units, with/without heating/ humidifier.
|
|
|
|
