|
|
Low cost - not low quality – LED underwater lighting from the industry leader.
Amphibians are the worlds first lighting collection designed to be used in or out of water. This new tough range was created firstly to satisfy the increasing demand for - high quality, - low cost - underwater lighting for smaller craft and secondly to counter the growing imports of cheap and ineffective LED underwater lighting, as we have always believed that the bitterness of poor quality remains long after the sweetness of low price.
All Amphibians utilize the latest ultra high output LED’s, have internal drivers for 12 or 12/24vDC usage, require a very low power draw with no start-up current and need a mere 8mm (5/16th) hole cut out for the cable. Utilizing unique OceanLED tritonium lensing with high tech injection moulded polymer casings resistant to all known solvents and adhesives, Amphibians are quick and simple to fit and are covered by OceanLED’s 2 year warranty. The Amphibians are exceptionally easy to install and can be used anywhere, such as;
• Transoms
• Engine Brackets
• Under the gunnels
• Trim tabs
• T-Tops
• Boat trailers for night launching.
• ROVs
• Tail gates
The A3, A6 and A12 are all now readily available in the USA, and other parts of the world, check with your local representative for details.
If its worth lighting up, then it deserves to be lit by OceanLED |
|
Docks, pilings, marinas, waterside restaurants and houses can now experience the underwater lighting phenomenon with our DV24 dock light. The light has a PVC housing with a 100 watt halogen lamp and is available in 12 volt a.c./d.c. The reflector is a 45 degree wide angle for maximum light output. The dock light is fastened to a flat surface by way of two mounting brackets. The light is fully submersible and IP68 rated.
|
|
The triple LED dock light (Ref. S40351) uses three 3 watt LED’s. The light is IP 68.
If this light is to be used underwater, the driver required is S41105 for each individual light.
If this light is to be used above water, the driver required is S41104 for every 2 lights.
|
|
Brand new lighting technology has allowed us to introduce the Sea Vision SV19 model. This utilizes a 50 watt xenon lamp and 50 watt ballast. This is the first of its kind to incorporate the ballast and ignitor built directly into the thru-hull casing. It is the brightest 12 volt DC light available. Can be installed on small to mid size boats including sportfishers and cruisers.
|
|
BEST MOUNTING SURFACE:
Fiberglass hull
REPLACING BULB:
Can be done from within vessel
BULB USED:
75 watt halogen bulb
LUMENS:
1,250
LIGHT LIFE:
Approximately 600+ hours
LENS TYPE:
Borosilicate glass lens is 0.4"/10mm
HOUSING:
Naval bronze
POWER SUPPLY:
12 volt running current 7 amps/ 24 volt running current 3 amps
INSTALLATION:
6" to 48" below water line
(Lenses tested to a depth of 300ft)
Spacing between lights is 6ft to 8ft
|
|
BEST MOUNTING SURFACE: Fiberglass hull
REPLACING BULB: Can be done from within vessel
BULB USED: 35 watt Xenon bulb
LUMENS: 3600
LIGHT LIFE: Approximately 6000+ hours
LENS TYPE: Borosilicate glass lens is 0.5"/15mm
HOUSING: Naval bronze
POWER SUPPLY: Our light is 12 volt start up current 18 amps for about 25 second & 3.5 amps continuous
INSTALLATION:
6" to 48" below water line
(Lenses tested to a depth of 300ft)
Spacing between lights is 6ft to 8ft |
|
Aqua Lights' bronze shines like gold and will never corrode!
Aqua Lights' AL600MH Bronze is sure to illuminate your water and the fish that surround you. At 300 feet viewing range, you are sure to see the dolphins at play and hovering sting rays! Aqua Lights is your best source for premium marine underwater lights at deeply discounted prices!
BEST MOUNTING SURFACE:
Fiberglass hull
BULB USED:
600 watt Metal Halide bulb
REPLACING BULB:
Can be done from within vessel
LUMENS:
160,000
LIGHT LIFE:
Approximately 6000+ hours
LENS TYPE:
Borosilicate glass lens is 0.6"/15mm thick
HOUSING:
Naval Bronze
POWER SUPPLY:
Dual ballast 120 (1 phase)-240 (1 phase) 280 (3 phase) volt, running current 1.5-0.75amps
CABLING:
Length of cable to ballast must not exceed 40ft, 15ft supplied custom length available
INSTALLATION:
6" to 48" below water line
(Lenses tested to a depth of 300ft)
Spacing between lights is 6ft to 8ft |
|
BULB USED: 35-watt metal halogen
BEST MOUNTING SURFACE: Fiberglass hull
REPLACING BULB: Can be installed from inside your vessel
LUMENS: 550
LIGHT LIFE: Approximately 900+ hours
LENS TYPE: Borosilicate glass
HOUSING: Naval bronze
POWER SUPPLY: 12 volts
CABLING: 10ft
INSTALLATION: 12" to 48" below water line (Lenses tested to a depth of 300ft) Spacing between lights is 5ft to 8ft |
|
The Sea Vision SV20 model is our standard xenon light with a 35 watt xenon lamp and 12 or 24 volt ballast. This light is suitable for small boats wanting to utilize 12 or 24 volt DC power and can be installed on sport fishers, center consoles, cruisers and performance boats.
|
|
The Sea Vision SV10 model offers the largest aperture of all the fiberglass models giving maximum light output from the 150 watt metal halide lamp. It can be installed in the transom or the hull and is suitable for boats with 110-230 volt AC power, including sportfish, yachts and cruisers.
|
|
| The UL Ti MATE 80 - 100 watt halogen (S02555) by Underwater Lights LIMITED ™ uses a 100 watt halogen lamp with 12 or 24 volt DC power. |
|
| The UL Ti MATE 80 55 watt Xenon (S02552), from Underwwater Lights LIMITED ™, model is our xenon light with a xenon lamp and 12 or 24 volt ballast. This light is suitable for small boats with 12 or 24 volt DC power and can be installed on sport fishers, center consoles, cruisers and performance boats. |
|
The UL Ti MATE 475 'SA' Super Adjustable (S00475) (patent pending) from Underwater Lights LIMITED ™ houses the new Super Adjustable unit which allows a change in beam direction of up to 20 degrees. This is available with either a 150 or 250 watt metal halide lamp with a 110-230 volt ELECTRONIC ballast, perfect for AC power on GRP/Fibre Glass hulls
|
|
The Sea Vision SV14 weld in model for aluminum hulls can be installed in the transom or the hull, it utilizes a 150 watt metal halide lamp and 110 or 230 volt AC power. The lights can be welded at adjustable angles to suit all hull shapes. The hull shape and positioning will dictate the angle of the light you require, angles available are 0-50 degree. All angle options are available on request.
|
|
The Sea Vision SV10 model offers the largest aperture of all the fiberglass models giving maximum light output from the 150 watt metal halide lamp. It can be installed in the transom or the hull and is suitable for boats with 110-230 volt AC power, including sportfish, yachts and cruisers.
|
|
Aqua Lights uses 316TI stainless steel that is nearly indestructible! This Aqua Light delivers a stainless underwater illumination solution for your night time marine-life viewing.
BULB USED: 175-watt metal halide bulb
LUMENS: 27,000
LIGHT LIFE: Approximately 6000+ hours
REPLACING BULB: Can be installed from inside your vessel
LENS TYPE: Borosilicate glass lens is 0.5" thick
HOUSING: Stainless Steel
POWER SUPPLY:
Dual ballast 120 (1 phase); 240 (1 phase); 280 (3 phase) volt, Running current 1.5-0.75 amps
CABLING:
Length of cable to ballast must not exceed 40ft 15ft supplied; Custom length available
INSTALLATION:
12" to 48" below water line (Lenses tested to a depth of 300ft) Spacing between lights is 5ft to 8ft |
|
The Sea Vision SV14 weld in model for steel hulls can be installed in the transom or the hull, it utilizes a 150 watt metal halide lamp and 110 or 230 volt AC power. The lights can be welded at adjustable angles to suit all hull shapes. The hull shape and positioning will dictate the angle of the light you require, angles available are 0-50 degree. All angle options are available on request.
|
|
The UL Ti MATE 75 SA 'Super Adjustable' (patent pending) weldin from Underwater Lights LIMITED ™ for aluminum and steel hulls can be installed in the transom or the hull. The SA reflector unit allows a change in beam direction of up to 20 degrees. This is available with either a 150 or 250 watt metal halide lamp with a 110-230 volt ELECTRONIC ballast, perfect for DC power on a yacht with either and aluminium or steel hull. A 30 and 50 degree angle is also available in both materials.
S00330 - 75 - SA - UL Ti MATE 75 SA 30 Degree Stainless Steel
S00350 - 75 - SA - UL Ti MATE 75 SA 50 Degree Stainless Steel
S00630 - 75 - SA - UL Ti MATE 75 SA 30 Degree 5083 Aluminium
S00650 - 75 - SA - UL Ti MATE 75 SA 50 Degree 5083 Aluminium |
|
IML Underwater Hull Light, 120/277VAC/150W (with lamp and ballast), stainless steel, clear lens, IP66, metal halide.
A high output 120/277VAC-150W (50/60Hz) Thru-Hull Light designed with utmost attention to thermal management (maintaining low operating temperature). Thermal cut-out switch will prevent overheating should the unit be left on while hull is out of the water when planing or during haul-out. Casing and bezel are made from 316 stainless steel. Also included is a high performance metal halide arc lamp & ballast. Ballast housing is complete with weather-proof connectors and pre-formed cabling. |
|
The OceanLED Puck Light fixture is designed to be used in Steel, Aluminium or Fibreglass hulls.
Cofferdams - We recommend tube for the Cofferdam walls to be sourced by the shipyard during installation to save on freight costs. OceanLED then supplies a Welding Back Plate which affixes to the tube creating the final Cofferdam for the light to be mounted.
Alternatively full cofferdams can be supplied.
For fibreglass hulls the follows along the same principal design where a molded pocket in the Fiberglass hull allows water to flow in and around the LED light enabling sufficient cooling.
If a General Arranagement (GA) can be supplied, our design department can assist in cofferdam design for maximum cost efficiency.
Full Cofferdams are available from us on request. |
|
The F-1 series offers a revolutionary new concept for underwater lighting for Super Yachts.
Achieving upto 25 degree hull angling within the fixture itself, it eliminates the need for massively long cofferdams, which improves Lamina flow and therefore fuel economy and ultimately speed whilst saving huge space inboard.
Being an LED powered unit (i.e. low maintenance) results in new thinking on yacht design. Old problems of access to 'traditional' underwater lights to change bulbs/service are now no longer as big a problem.
The F-1 Series is the most technically advanced underwater light every created. The unique 3 part delivery system offered by OceanLED ensures the very latest LED technology is utilized when the yacht is ready for launch.
Stage 1 - The Cofferdam assembly is delivered for the hot work (welding) to be completed.
Stage 2 - The electronics and cabling are supplied when needed.
Stage 3 - Light engine is delivered at the last stage to ensure the very latest LED technology is used.
The F-1 is currently being fitted to the latest new builds at the Feadship, Koninklijke De Vries Aalsmeer and Koninklijke De Vries Makkum facilities.
|
|
The Sea Vision SV10 model offers the largest aperture of all the fiberglass models giving maximum light output from the 150 watt metal halide lamp. It can be installed in the transom or the hull and is suitable for boats with 110-230 volt AC power, including sportfish, yachts and cruisers.
|
|
| Underwater floodlights complete Yachtlite's extensive product palette for yachts. Yachtlite provides highest quality underwater floodlights with certification from a long-standing reputable manufacturer. |
|
| ... products without information |
| |
|
|
Underwater lighting
