|
|
Performance:
Static Suction Lift:
15 ft / 4.57m
Dry Suction Lift:
12 ft / 3.65m
Discharge Head:
15 ft / 4.57m
Max Volume:
40 GPM / 152 LPM (at 60 cycles per minute)
Construction:
Pump Base:
(Wetted Parts)
Choice of:
Anodized Aluminum
Marine Bronze
Urethane Powder Coating
PTFE Coating (HALAR)
Diaphragms and Valves:
Choice of:
Nitrile
Viton
Hypalon
Mounting Frame:
Powder Coated Aluminum
Hardware Material:
Stainless Steel
Drives:
Electric Powered with Choice of Close Coupled:
3/4 hp tefc motors all voltages, 1ph or 3ph
3/4 hp explosion-proof motors
3/4 hp teft 12v and 24v motors
|
|
Self-priming diaphragm pump with 12v, 24v or 32v DC electric motor. Flow rates up to 17 litres/min (4.5 US gallons/min), pressure switch control, capable of pressures up to 3.2bar (45psi)
Features
Self-primes up to 2.4m vertical lift
Four-piston design delivers higher flow rates
Quick-connect plug-in ports for easy installation
Pressure-switch control to run the pump only as needed
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 12.5 litres/min (3.3 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
Oil resistant elastomers - suitable for diesel transfer
|
|
Features:
Compact Design Measuring 6.4" (162 mm) in Length
Fully Automatic Demand Pump
Self-priming and Can Operate Dry Without Damage
Built-in Thermal Protector
Sealed Pressure Switch and Motor
Flow Rates to 1.0 GPM (3.8 L/min.) and Operating Pressures to 25 PSI (1.7 bar)
Compact automatic demand pump.
Sealed pressure switch automaticatly starts and stops pump when discharge valve is opened and closed.
Self-prlming so pump can be located above supply tank.
Can run dry for extended periods of time without damage.
Built-in thermal protector
Low amp draw for battery powered applications.
Soft compliant Santoprene mounting system.
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 18.9 litres/min (5 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
Includes strainer, 3/4" hose barb and 3/4" garden hose ports
|
|
|
|
|
|
|
DC Driven Flexible Impeller Pumps
Pumps suited for use in boats as bilge and deckwash pumps, fresh water pumps, refuelling pumps for oil and diesel. Can be combined with a vacuum switch for automatic operation. Capacities vary from max 14 l/min to 55 l/min, allowing the proper matching of the pump to the application. All motors are heavy duty to provide long service life even under heavy use.
F3B-19 F38B-19 F4B-19 F5B-19
Perfect for bilge pumping, deckwash, water circulation, oil and diesel refuelling at dockside service, etc.
F3B-19 Oil Change
Reversible rubber impeller pump with integrated quick reversing switch. Designed to remove old oil from the engine/fill new oil back into theengine.
F4B-11 Ultra Ballast
Designed to quickly fill or, when reversed, drain a ballast tank at a rate of more than 45 l/min (12 GPM). Capable of pumping fresh or sea water the pump's robust design can handle the rigors of continuous duty usage, is reversible, and has a built in thermal overload for added protection. Care not to run dry for extended periods of time will increase the pump longevity and ensure reliable performance for many years.
Note! Only for waterhandling.
|
|
- Constructed from marine quality bronze and stainless steel for ruggedness and reliability.
- Easy to service and maintain.
- Inexpensive to buy and operate.
- Will tolerate abrasive wear (this may affect performance - seek advice from your distributer).
- Handles hard and soft solids without clogging.
- Can pump in either direction.
- Will not airlock.
|
|
Flow rate: 32 Litres/min (6.5 gallons/min)
Self-priming from dry up to 1.2m (4ft)
- Small bilge debris present no problem to these bronze bodied, flexible impeller pumps.
- Simple design means fewer wearing parts.
- ISO 8846 MARINE (Ignition protection).
- ISO 8849 MARINE (Bilge pump standard).
|
|
Features:
- Small bilge debris present no problem to these bronze bodied, flexible impeller pumps.
- Simple design means fewer wearing parts.
- ISO 8846 MARINE (Ignition protection).
- ISO 8849 MARINE (Bilge pump standard).
|
|
|
QL pumps are versatile and therefore ideal as deckwash and bilge pumps, for pumping fresh water and diesel fuel. The combination of a Vac-on-Switch provides extended battery life as well as preventing the pump from running dry.
|
|
- Quiet operation
- Runs dry without damage
- Inlet strainer included
- Quick Connect ports with adaptors included
- Suitable for use with saltwater and freshwater
- Self-priming up to 3 m (10 ft)
- Smooth constant flow
- Extra protection and safety with wires and pressure switch
housed internally
- Universal mounting arrangement fits any existing installation
|
|
|
Self-priming pump, fitted with neoprene rotors; watertight in accordance with ISO 8846 standards (may be installed on the engine room) - Version A: Electrophoresis enamelled engine casing - Version B: Model MKII fitted with pump unit made of resin-thermosetting reinforced fibre glass + stainless steel internal inserts.
|
|
A line of compact magnetic driven centrifugal pumps, CM-series, which combine high flow rates with very low electric current consumption, making them ideally suited for circulating fresh water in live fish tanks, heating and cooling systems. C090 with mechanical seal and a motor designed for continuous operation.
Designed also for fresh water handling.
|
|
Dometic marine holding tank system – a clean and easy solution to fit every boat
“Fit-and-forget” pump design – Dometic DTW-series waste discharge pumps are based on a unique bellows design that makes them last longer than other manufacturers’ rubber diaphragm pumps. Running quietly, they easily handle over 1000 litres of waste per hour. Available for either 12 or 24 volts DC.
Waste discharge pump
› Long-life bellows design
› Quiet operation
› Runs dry without damage
› Handles liquids and solids
|
|
POSSIBLE CONNECTIONS
Shower, sink
VERTICAL PUMPING HEIGHT UP TO
4 m
OUTLET DIAMETER
22 mm to 32 mm
MAX WASTE WATER TEMPERATURE
35°C
SUPPLY VOLTAGE
12 V or 24 V
MOTOR POWER RATING
360 W
|
|
Viking Power 16
A modern, single-chamber, self-priming diaphragm pump that can be set up in several different pump/motor configurations. It is easy to install anywhere after the drain outlet in the wastewater system or as a bilge pump in any leisure craft – new or used.
Its non-choke valves mean that no in-line filters are necessary. The pump can be run dry, and it can also handle a mixture of air and water without difficulty. The Viking Power 16 is self-priming up to a height of 3 meters.
With its low pulse and muffled rubber bracket, this pump offers quiet operation. Specifically designed to pump waste water, the Viking Power 16 has been built to last, and engineered for easy maintenance. When it comes time to replace the premium grade reinforced nitrile rubber diaphragm, you can put in a spare without even removing the pump from the system. Delivered with 1” hose and ¾” hose ½” BSP KlickTite™ XL connectors. 90° KlickTite™ XL connectors available as extra accessory.
|
|
Edson Air Powered Diaphragm Pumps are the most
versatile of all Edson Pumps due to the flexibility of
the air cylinder drive. They are used for the collection
and transfer of waste liquids and pumping liquids with
suspended solids. They are capable of handling
liquids with large suspended solids without clogging,
to prime from dry starts, and to run dry. They have
the added feature of low emulsive, non sheering
pumping action. These basic performance features
and Edson’s 140 year history of manufacturing quality
products have made our pumps the choice for cleaning
up our environment and controlling the disposal of
liquid waste. Evident by the list of applications the
pumps can be used including the requirements for
ground water remediation, containment transfers,
dewatering, oil and water separations, marina and
campground sewage collection, tank, sump and drum
transfers, filtration applications, and the collection and
transfer of abrasives, slurries.
|
|
Features:
Variable Speed Control
Solid State Pressure Sensor
Nearly Silent Operation / No Cycling
Operates on l2Vdc or 24Vdc
Controls Pressure by Changing Motor Speed
Speeds Up As Demand Increases
Self-priming / Runs Dry
No Accumulator Tank Needed
CSA Listed / EN ISO 8846 Marine / C.E. Certified
Specifications:
Motor Permanent magnet, double ball bearing armature. Electronic speed control built into rear endbell.
Pump Four chamber positive displacement diaphragm design. Self-priming up to 10 feet suction lift. Pump able to run dry without damage. Removable port adapters.
|
|
|
Self-priming diaphragm pump with 12v, 24v or 32v DC electric motor. Flow rates up to 17 litres/min (4.5 US gallons/min), pressure switch control, capable of pressures up to 3.2bar (45psi)
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 18.9 litres/min (5 US gallons/min)
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor.
Features:
• Self-primes up to 10ft (3m) vertical lift
• Runs dry without damage to the pump
• Quick-connect plug-in ports for easy installation
• Oil resistant elastomers - suitable for diesel transfer
|
|
Flow rate: 13.7-16.3 Litres/min (3.7-4.5 gallons/min)
Self-priming from dry up to 2.4m (7.8ft)
- Variable Speed Control
- Solid State Pressure Sensor
- Nearly Silent Operation / No Cycling
- Operates on 12V DC or 24V DC
- Controls Pressure by Changing Motor Speed
- Speeds Up As Demand Increases
- Self-priming / Runs Dry
- No Accumulator Tank Needed
- CSA Listed / EN ISO 8846 Marine / C.E. Certified
- Protected under U.S. Patent #6,607,360
- Includes Inlet Strainer
|
|
Features:
- Smooth flow
- Dry running capability
- Soft noise absorbing mounts
- Snap-fit port fittings
- Built-in bypass -less pulsation
- Reduces need for accumulator tank
- Corrosion resistant materials
- CSA listed
- ISO 8846 MARINE (ignition protection)
- CE
|
|
Features:
- Smooth flow
- Dry running capability
- Soft noise absorbing mounts
- Snap-fit port fittings
- Corrosion resistant materials
- Meets USCG Regulation 183.410 and ISO 8846 MARINE (ignition protection)
- Meets EN 50081-1 Electro-magnetic Compatibility
|
|
|
QL Water Pressure Pumps for water supply to the galley and shower - you just turn the tap or taps and the water flows. The water pressure pumps are suitable not only for fresh water but also for salt water.
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 12.5 litres/min (3.3 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 12.5 litres/min (3.3 US gallons/min)
|
|
Features:
- Flexible installation
- No filter required
- Compact and simple design
- Dry running capability
- Relevant Standards: ISO 8846 MARINE and USCG Regulations for Ignition Protection ISO 8849 MARINE Bilge Pump Standard
- Built to ISO 15083 Specification
- Meets BSEN 50081 (Electro Magnetic Compatibility)
|
|
This greywater transfer station - GWH works automatically.
The system is designed to be connected to showers, wash basins, kitchen sinks and all places where waste water can not run with the help of natural fall. The system consists of a durable collecting vessel, available in polyethylene (PE) or in stainless steel. At the front 2 inlet pipes 1” and 1 ½” and a ventilation connection ½” can be found. The discharge pump is our hard-wearing waste water pump F. On the inside of the collecting vessel there is a float switch. Due to the use of a pump with cutting wheel hair and kitchen leftovers are chopped and conveyed without any problems. The arising waste water is disposed via a pressure pipe (1”). The integrated pressure lip valve contains a safety valve which prevents a flow back of waste water. The station works up to a tilt angle of 45°.
|
|
- Swivelling outlet
- Ideal for use with two sinks
- Fine flow control
- Light back & forth pump action
- Suitable for fresh water
- 7 litres (2 US gals) per minute
|
|
|
|
Boat water pumps (freshwaters, waste waters)
