|
|
Grease separators are suitable for ships of all sizes. Units range from simple manually operated ones to advanced and fully automatic ones.
Grease separators are easily operated with low maintenance. Special grease traps can be connected to vacuum piping.
|
|
To avoid clogging of grey water tanks and waste water systems a grease separator should be installed for the all grey galley water. The grease separator is specially designed for marine applications, so it will work even if the ship is rolling.
Unlike many other grease separators the ours has a proven 99.5% separation
efficiency (tested and approved by the Royal Institute of Technology in Stockholm), so the water is free from grease and oil and can be led directly to the grey water system or treatment plant.
The grease separators are equipped with automatic grease level alarm that alerts when it is time to empty the separator of fat. On the top of the inside there is a spray nozzle for cleaning with hot water.
|
|
|
Grease Separators in Stainless Steel 304 with grease storage capacities form 12 litres up to 220 litres
|
|
Purification or clarification of distillates, marine diesel oils, intermediate and heavy fuel oils, and lubricating oils used in marine installations and power stations.
The MOPX separation system is designed for automatic intermittent discharge of separated sludge.
Concept
Each MOPX Separation System comprises:
- an MOPX separator
- ancillary equipment including EPC-41 control unit.
The separator can be delivered with or without built-on feed pump. An installation with a separate feed pump is recommended.
Features and benefits
The main features of the system are:
- Simple and robust design.
- EPC-41 electronic control unit with built-in PI temperature controller for any type of steam heater or Heatpac electric oil preheater.
|
|
|
|
|
|
|
CJC%u2122 Filter Separators combine fine filtration with water separation all in one unit, with an integrated circulating pump. They are designed for use in applications containing hydraulic oil, diesel fuel, lubrication oil, etc., in which water ingress is a constant or recurrent problem.
CJC%u2122 Filter Separators remove water by coalescence and at the same time minimize oil contamination levels of particles and oil degradation products (oxidation resin/sludge, varnish).
The CJC%u2122 depth filters have a filtration degree of 3 microns absolute and a very large dirt-holding capacity.
This, combined with efficient and continuous water removal from the oil, provides numerous benefits including reduced maintenance, increased productivity, and maximum lifetime of system components, in-line filters and oil.
The modular Filter Separators are built and sized to specific customer requirements - whether the oil volume is 2 litres or 200,000 litres.
CJC%u2122 Filter Separators ensure trouble-free operation of marine hydraulics, marine diesel fuel systems, steam turbine lube systems and water-cooled hydraulic industry equipment.
|
|
As a flexible module manufacturer and our knowledge in HFO processes we are the right partner to deliver separator plants. The separator plants are mainly used to remove the water and mechanical impurities contained in fuel and lubricants for diesel engines.
From small to very large plants we are capable to deliver custom designed units with the separator brand of your choice. The same advantages apply here as for our booster modules. We give an added value to the separators which is unsurpassed in the industry.
|
|
|
The Hamworthy oily water separator is an advanced plate type separator which separates oil and water using the natural density differential to achieve IMO standards of performance.
|
|
|
|
|
|
|
A complete pollution-prevention solution for bilge water, the PetroLiminator is a U.S. Coast Guard (USCG) and International Maritime Organization (IMO) approved oily water separator (OWS) that easily handles phase-separated oil, emulsified oil and water. Properly used, the system takes suction directly from the ship's bilge or oily water collection tank and reduces the total petroleum hydrocarbons to less than 15 parts per million. Emulsified oil is easily handled by the system, whether caused by detergents and/or the ship's mechanical systems.
This automated bio-mechanical system is safe, reliable and requires low maintenance. Unlike conventional oil water separators, the PetroLiminator actually destroys oil and grease using naturally occurring bacteria. The technology used in the PetroLiminator has been successfully used in hundreds of land-based applications since the 1970's. Now, the PetroLiminator has been improved and specially designed for shipboard applications. EnSolve received a patent in 1998 for shipboard use of the PetroLiminator.
|
|
|
The Hyde Marine Separator, developed in the early 1970's, uses Hyde's proven and reliable method for gravity separation of oil from bilge water to less than 15 ppm. The separator exceeds all performance requirements of U.S. Coast Guard 46CFR162.050 and IMO Resolution MEPC.60 (33) and is certified by the U.S. Coast Guard.
|
|
|
|
|
|
|
OILY WATER SEPARATOR
PETER TABOPADA® has combined more than 20 years of experience with the highest technologies in oily water separation. This experience has allowed us to get the most reliable system of the market. The system design is based in the gravity principle and coalescence that means a separation media with no consumables. it is the most important characteristic of this equipment, because it reduces significantly maintenance expenses, as cartridge and filtration media.
OCD CM BILGE MONITOR
This alarm uses an optic system based in the principle of light scattering. It uses a pure aluminium sample cell, which is an aluminium structure, placed inside a box. the optic devices are placed inside an aluminium box that contains the light source, the scattering detector, the transmission detector and the thermal protector. Whenever the oil concentration is higher than 15 PPM, the equipment automatically changes to alarm mode in order to notify the operator and change the water flow to recirculation mode. We also have equipment for monitoring less than 5 PPM
|
|
Oily water or bilge water separators that provide the maximum efficiency with the easiest operation and maintenance.
We dispose of a wide range of equipments, for any size required. Thanks to the use of high quality and reliability components, our separators are ready to withstand the harsh work conditions on board guaranteeing always the best performance.
|
|
The Wärtsilä Senitec M-series system gives the operator effective control over all bilge and sludge media, as well as over any discharges into the sea.
The system conforms to the highest safety standards, which besides being an essential factor in its’ competitiveness, is also a substantial value in itself. No accident, discharge, or injury should be caused by our equipment. The Wärtsilä Senitec M-series is approved according to IMO resolution MPEC 107(49), which came into force on January 1st, 2005. An entirely new leading-edge separator is at the heart of the system. Rigorous testing, including extensive onboard trials, have been carried out with excellent results.
|
|
Purification or clarification of mineral oils used in marine installations and power stations (fuel and lubricating oils).
Separation takes place in a solids-retaining bowl that can be arranged for either clarification or purification. In both cases, the contaminated oil is fed into the separator through the centre, and it is separated by centrifugal force into its various phases, the heaviest phase (sludge and water) being forced outwards to the periphery of the bowl. The accumulation of sludge is periodically removed from the bowl by hand.
Installation
The oil is pumped, heated, and separated as shown in the figure. A liquid seal in the separator bowl prevents the oil from escaping through the water outlet. If this seal is broken, an alarm device is activated. With unmanned engine rooms, the
signals are transmitted to a remote control unit. When the seal is broken, the three-way valve shuts off the oil feed and the oil is recirculated until the fault is corrected.
|
|
The CJC%u2122 Blue Baleen Bilge Water Systems are polishing systems, used to absorb oil from bilge water to below 5 ppm.
Based on a unique absorption principle with the specially developed and patent pending CJC%u2122 Blue Baleen CJC%u2122 OilAbsorb Inserts, the systems absorb oil from bilge water, process and wastewater, ensuring environmentally friendly operations and constant compliance with the IMO MEPC Standard.
Typical applications are marine bilge water systems, wastewater treatment, rinse water and process water for recycling purposes.
With low operational costs, and practically no maintenance requirements, the CJC%u2122 Blue Baleen Bilge Water Systems are cost-effective solutions to bilge- and wastewater problems within industry and marine applications.
|
|
|
|
|
|
|
The excellent performance and RWO's more than 30 years of experience with oil/water separators guarantee a high performance standard, more than 9.900 ships have already been equipped with this efficient system.
The SKIT/S-DEB oil/water separator complies with the actual IMO Resolution MEPC.107(49) using the combination of the highly effective open porous coalescer together with a second stage emulsion breaking oil and hydrocarbon polisher. Periodical backflushing keeps the coalescer surface clean and offers long lasting operation without requiring attendance and maintenance.
Advantages at a Glance
Complete package, skid mounted systems for least amount of onboard installation wor
Vacuum or pressure systems
Complying with 5 ppm standard
High performance standard with hydrocarbon polisher
Continuous automatic effluent control to protect adsorber and to minimise consumables
Oily water separators for offshore application
De-oilers and grease extractors for condensate
Easy to install and easy to handle
Pre-tested in our workshop testing facilities
Type approved acc. to IMO-Resolution MEPC 107(49) by USCG, SBG, MED, MRS, CCS
Worldwide Service & Support
|
|
|
|
|
|
|
Oily Water Separators
More than ever before, the reliability of bilge water separators is in the focus of public interest. Our decades of experience in the production of bilge water separators and our comprehensive know-how for their onboard operation and maintenance led to the development of the two-stage Turbulo Mechanical Phase Breaker (TMPB). It benefits from the 80 years of experience with our traditional Turbulo oily water separator and, of course, meets the requirements of IMO Resolution MEPC.107(49).
Your benefits at a glance:
- Residual oil content in the outlet water well below 15 ppm
(test results near 1 ppm)
-Compact dimensions
- Small space requirement
- Simple installation
- Easy maintenance
- Fully automatic operation
- Separate installation of pump and second stage possible
Because the analysis of bilge water is very complex by its nature, our in-house laboratory is well equipped to analyse and determine, among other things, the oil content according to ISO 9377-2, the particle size of the hydrocarbon index and the interfacial tension.
|
|
The DMA Sep-Line is a completely new line of separator systems combining new technology and well known principles to obtain the most efficient bilge water separation guaranteeing outlets below 5 ppm. The system is unique of its kind, with no moving parts in the first stage and deals effectively with problems with particles and oil emulsions.
Specifications:
Our filter containers represent the latest state of the art design in stainless steel 316 L with small footprint and low weight as well as an easy lid opening without use of tools.
Connections: In- and outlet 1,5" to 2,5"
Flow/temperature: 0,5-5m3 /60 ºC
Design pressure/ test pressure: 6/9 bar
Discharge bilge quality: 0-14 ppm
Power supply: 380v 50Hz
Coalescer material: Polyethylene
Closure: Cast Vee clamp
Finish: Electro polished inside and out
Gasket: Ethylene Propylene
|
|
OceanClean EB 0,25
with a capacity of 0,25m³/h.
Type tested and approved by Lloyds Register of Shipping according to IMO-Resolution MEPC 107(49).
|
|
OceanClean EB 2,5
with a capacity of 2,5m³/h.
Type tested and approved by Lloyds Register of Shipping according to IMO-Resolution MEPC 107(49).
|
|
OceanClean EB 5,0
with a capacity of 5,0m³/h.
Type tested and approved by Lloyds Register of Shipping according to IMO-Resolution MEPC 107(49).
|
|
OceanClean EB 1,0
with a capacity of 1,0m³/h.
Type tested and approved by Lloyds Register of Shipping according to IMO-Resolution MEPC 107(49).
|
|
OceanClean EB 0,5
with a capacity of 0,5m³/h.
Type tested and approved by Lloyds Register of Shipping according to IMO-Resolution 107(49).
|
|
|
Oily Water Separators - USCG and IMO certified Oily Water Separators designed to separate oil and water below 15PPM. Heavy-duty construction, non-corrosive materials, fail-safe monitoring results, permanent oil attractant media, quiet operation and smooth flow result in an easy to use, high quality, affordable solution to your oil separation needs.
|
|
OceanClean EB 0,5 stainless steel
with a capacity of 0,5m³/h.
Type tested and approved by Lloyds Register of Shipping according to IMO-Resolution MEPC 107(49).
Other sizes are available on request.
|
|
| ... products without information |
| |
|
|
Liquid / liquid separators for ships
