|
|
|
Odour filtration, designed for Luxury Yachts and Inland Cruise Vessels, but applicable for every kind of ship.
|
|
Contains activated carbon filter material
that removes unpleasant odors.
Keeps your boat smelling clean and fresh.
- Each filter is good for an entire boating season.
- Vent Filter overall length is 15 5/8".
|
|
Dometic marine holding tank system – a clean and easy solution to fit every boat
Looking for an effective means to stop odours escaping through the holding tank vent? The Dometic vent filter uses a unique filter material that captures heavier-than-air gases. It keeps your boat smelling clean and pleasant without any chemicals added to the tank. Each cartridge is good for an entire season, and is easily replaced.
Vent filter
› Specially formulated odour-removing filter material
› No need to add chemicals to the holding tank
› Easy-to-replace filter cartridge
› Supplied with installation fittings and hose adapters (Ø 16 and 19 mm)
|
|
|
The particular specification of polyethylene (food grade quality) which TEK-TANKS use will not corrode and provides clean, taste free water for the galley.
|
|
SeeLeveL 709, multi tank monitor system
This system provides an outstanding balance between low cost and full features. Instead of single points that give you only a close appr. of how full your tanks are this system offers a continuous level and shows an actual number, in percent of full.
Measures tanks up to 300 mm tall with a single sender or 600 mm tall with dual senders. 3 sender boards are included.
Art No 970213
|
|
SeeLeveL 707, multi tank monitor system for plastic tanks
This level gauge has an easy to read LED display. Display fresh, gray, or black tank levels at the press of a button. 9 segmented display gives accuracy to 1/8 (12.5%) of a tank. Orange and red indicators are used for low and empty level warnings for the fresh water tank. Orange and red indicators are used for high and full level warnings for the gray and black water tanks. 3 sender boards are included.
Art No 970206
|
|
SeeLeveL 713, multi tank monitor system
No buttons to push! The level of each tank, plus the outside temperature, is shown individually. 713 provides accurate tank level information in percentage of full. Measures tanks up to 430 mm tall with a single sender or 840 mm tall with dual senders. 3 sender boards are included.
Art No 970220
|
|
In addition to accuracy and reliability the TD 4000 comes standard with many intelligent features to measure up to four tanks, four batteries, or a combination of both.
The Smartswitch TD 4000 tank sensor is suitable for diesel, petrol, grey, freshwater and black tanks.
It is suitable for all tank construction materials including stainless steel, plastic and fibreglass.
Simple to install, the TD 4000 comes with two setup options depending on regular or odd tank shape.
Two point calibration for regular shaped tanks (low and full) and five point calibration for odd shaped tanks.
|
|
Full control from one central location on your boat.
Visual indication of tank level, seacock position & pump status.
Turn holding tank macerator pump on manually & off manually or automatically.
Turn water maker on/off manually or automatically.
All tanks are name selectable giving tank type. e.g. (Grey Tank 1) (Black Tank 1) (Fresh Tank 1)
(Fresh Tank 2).
Two display modes available (see right).
Displays in Litres or Gallons and Percentage.
Backlight.
|
|
|
|
|
|
|
Dometic marine holding tank system – a clean and easy solution to fit every boat
Tried and tested in thousands of installations, Dometic holding tanks provide a clean and safe service for many years. Top-mounted hose connections and an extra-thick wall of durable polyethylene give a leak-proof and odourfree design. Handy for do-it-yourself enthusiasts: all holes are pre-cut, all fittings are pre-installed and tested in the factory. Two separate discharge outlets eliminate the need for extra plumbing connections. Add to this a comprehensive range of well-planned accessories, and you’ll get an all-in-one, no-worry solution. Dometic holding tanks are available in five sizes to fit all common types of boats.
Holding tank
› Leak-proof, odour-free design in highly durable polyethylene
› Pre-installed and tested fittings that can rotate
› Separate outlets for dockside and overboard discharge
› Discharge tubes in special non-clogging design
› Level indicator, discharge controls are easily retrofitted
› Vacuum relief valve prevents damage from high-capacity dockside vacuum pumps
› Compliant with ISO 8099 requirements
› 5 year warranty
› Choice of 5 models ranging from 42 to 137 litres
|
|
|
Automatic Marine SuperSump® Shower Sump Tank - Trionic's 2-gallon, 4-gallon (shown) 10-gallon and 14-gallon large capacity automatic shower sump eliminates the overflow problems of small capacity units
|
|
|
|
|
|
|
|
TRIONIC offers an extensive line of Marine and RV water and holding tanks to meet most size and durability requirements. All tanks are rotationally molded of a seamless one piece, non-corrosive linear polyethylene that meets FDA acceptance and complies with Coast Guard regulations. Each water tank has one 1/2" supply opening, one 1-1/2" fill opening and one 1/2" vent. Each holding tank has one 1/2" vent and has two 1-1/2" openings. Openings on all tanks are female National Pipe Threads (NPT) and are located on one end of the tank. We offer custom fitting locations and an optional 3" cleanout or inspection port. All of our tanks are guaranteed to be extremely durable and will not collapse when emptied with high capacity pumps. All tanks can be special ordered with 3/8" wall thickness. If you do not see the tank dimensions that you need on our website, please call to see if we have a tank to suit your needs. We have many sizes that are not listed here. Custom fitting locations are available upon request.
|
|
|
These tanks are plain tanks with no fittings. Tek-Tanks can however, "fit up" these tanks to your requirements. You tell us what fitting and where you want it.
|
|
|
|
|
|
|
Installed and ready to use in 30 minutes!
Gobius is the first level indicator in the world that measures from the outside. Installing Gobius to your tank is very easy. Instead of the traditional way of installation, i.e taking the tank apart and drilling holes, you simply attach the sensors to the tank on the outside.
All Gobius products measure from the outside
Very easy to install and setup
Suitable for all tank materials; stainless steel/steel, aluminum, plastic and fibre glass
Gobius can be retro-fitted to any shape or size of a tank
Analouge output for gauges from Wema, VDO, Faria, Teleflex, Phillipi…
Supports NMEA 2000
Extremely low electricity consumption, less than 40 mA (12 Volts)
Support 12 – 24 Volts
30 minutes to install
On the sensor there is a disc of tape that is provided to attach the sensor directly onto the surface of your tank. The panel may be placed in the washroom. All necessary cables and plugs needed to connect the sensors and the panel with the control unit are included.
Very easy to calibrate
No tanks look the same. There are always differences in e.g. size, construction, thickness and age. In order to compensate for these differences you have to calibrate the tank before you start to use your Gobius. However, the calibration only takes a few seconds.
The Gobius technology (patented)
Each sensor that is placed onto the tank wall consists of a shaker and an accelerator. When the shaker creates a vibration in the tank wall, the accelerator measures the size of the vibration and passes the data on to the control unit.
Art No 970497
|
|
Continuously monitors 3 levels of holding and water tanks and monitors battery level. Includes rocker switch for pump if needed. Suitable for tanks up to 26" tall. Optional grey water tank sensor available.
- Easy to Install
The Smart Sense System is attached to the outside of the tank as shown.
- Reliable
No micro float switches or probes to degrade and fail. Electronic sensors are outside the tank
- Attractive and User Friendly
Smart Sense System includes a display panel with LED lights and hidden mounting screws inside snap out mounting bezel.
|
|
|
|
|
|
|
Installed and ready to use in 30 minutes!
Gobius is the first level indicator in the world that measures from the outside. Installing Gobius to your tank is very easy. Instead of the traditional way of installation, i.e taking the tank apart and drilling holes, you simply attach the sensors to the tank on the outside.
All Gobius products measure from the outside
Very easy to install and setup
Suitable for all tank materials; stainless steel/steel, aluminum, plastic and fibre glass
Gobius can be retro-fitted to any shape or size of a tank
Analouge output for gauges from Wema, VDO, Faria, Teleflex, Phillipi…
Supports NMEA 2000
Extremely low electricity consumption, less than 40 mA (12 Volts)
Support 12 – 24 Volts
30 minutes to install
On the sensor there is a disc of tape that is provided to attach the sensor directly onto the surface of your tank. The panel may be placed in the washroom. All necessary cables and plugs needed to connect the sensors and the panel with the control unit are included.
Very easy to calibrate
No tanks look the same. There are always differences in e.g. size, construction, thickness and age. In order to compensate for these differences you have to calibrate the tank before you start to use your Gobius. However, the calibration only takes a few seconds.
The Gobius technology (patented)
Each sensor that is placed onto the tank wall consists of a shaker and an accelerator. When the shaker creates a vibration in the tank wall, the accelerator measures the size of the vibration and passes the data on to the control unit.
Art No 970459
|
|
|
|
|
|
|
SENDER LEVEL WITH ALARM 4-20 MA. SIZE 10 TO 100 CM
Codice prodotto: HP--G00XX4-20
INTERNATIONAL PATENT.
Our new capacitive level sensor provides measurement accuracy, reliability and quality. It was designed to respond to the request of a sensor accurate, durable, universal and easy to use. The following features will reflect the advantages:
- The capacitive level sensor is compatible with all 4-20 mA gauges on the market. It is not compatible with STD (240/33 Ohm) and VDO type (10/280 ohms) gauges.
- It can be connected, properly powered, to the gauge replacing any other existing 4-20 mA sensor, with no special precautions needed.
- It is equipped with an exit alarm that may be audible or visible, and is programmed to 20% (for %u2018empty%u2019 alarm) or 80% (for %u2018full%u2019 alarm).
Capacitive level sensors can be used for FUEL, WATER and WASTE WATERS.
The capacitive sensor is currently produced with lengths ranging from 10cm to 100cm.
The %u2018Reed%u2019 level sensor is universal and therefore can be used for all liquids (white waters, black waters, fuel). The capacitive sensor instead exploits the properties of the liquid the level of which is to be measured and therefore has a structure created on purpose for the liquid of interest. In particular, we produce two types of capacitive level sensors, one concerning the fuel sector and one concerning the white waters and black waters%u2019 sector (for measuring the water level the sensor is then the same but has two different types of alarms %u2013 %u2018empty%u2019 for white waters or %u2018full%u2019 for black waters).
|
|
The unique Smart Switch Programmable Toilet Controller was designed for all electric marine toilets with a single motor/pump flushing system. The stylish control panel provides fully automatic programmed flushing when either button is pushed.
This unit features a Full and Half Flush cycle providing for a water / holding tank save mode.
Features includes automatic voltage sensing as well as 'Over Voltage' 'Over Temperature' 'Short Circuit' 'Over Current Protection' and 'Open Circuit Detection'.
Easy Installation and easy operation the switch control panel comes in either Black, White, Brushed Stainless Steel or Polished Brass making this an attractive product to suit most needs.
This product employs State of the Art Microcomputer Technology and is completely encapsulated in silicon protecting the electronic components from the harsh marine environment insuring long-term life & reliability
|
|
|
|
|
|
|
The unique Smart Switch Deluxe Programmable Toilet Control was designed for all electric marine toilets with remote, fresh or salt water flushing supply via an inlet pump or water solenoid valve. The stylish control panel provides fully automatic programmed flushing when the auto touch pad is pushed or provides
independent operation of the inlet or discharge pumps for maintenance or line clearance when the manual touch pads are used.
In-built troubleshooting features and toilet pump protection are standard. Other features include automatically sensing your vessels supply voltage and self-adjusting to suit 12, 24 or 32-volt systems, protection from radio interference and ZERO current draw.
With the built in intelligence this device will sense for toilet blockage, overheating, pump and valve short circuit, & pump open circuit, automatically cut off and display an error code protecting your complete system.
This Model is truly versatile with two different timing sequences built in. This feature is user program selectable ( Change modes in a flash).
Easy Installation and easy operation, the switch control panel comes in either Black, White, Brushed Stainless Steel or Polished Brass making this an attractive product to suit most needs.
As with all Smart Switch products, the Deluxe Toilet Controller employs State of the Art Microcomputer Technology. This, and the fact it is completely encapsulated in silicon, protecting the electronic components from the harsh marine environment, guarantee long-term life & reliability.
|
|
Codice prodotto: HPSN0002 / HPSN0003 / HPSN0004 / HPSN0005
In 2005 a new line of wastewater tanks was added to the product line of SIC Divisione Elettronica.
Certified in compliance with ISO 8099
- The tanks are made in 55, 77, 160 and 207 l main versions but can be customized %u2013 OEM solutions - to fit the customer%u2019s exact specifications.
- The wastewater tanks are made of extra strong metallocene (mMDPE) polyethylene with superior mechanical properties.
- The tanks are resistant to solvents, acids and other surface-active agents.
- They withstand high pressures. These tanks were tested under the pressure that by far exceeded resistance requirements.
- The tanks come complete with all the necessary accessories and a new capacitive electronic level sender of the highest quality and measurement precision.
- They are light-weight
- They are certified to comply with all the strictest requirements of ISO 8099 Safety Standard
- These tanks undoubtedly offer the best value available.
|
|
|
Our tank sensor is driven by the air pressure generated by the water level. It must be installed in the upper part of the tank with the rubber hose that enters the tank so that, when the level of the water increases reaching the rubber hose, the pressure switch effects the contact. The pressure switch, located outside the tank, is a normal on-off switch that, being electrically connected with the control panel of our WCs (grey/black cable), warns through a red led that the tank is nearly full (usually the led is green). The sensor may be used to commutate different alarms.
|
|
Features:
- Extra heavy duty white sanitary hose is manufactured for Jabsco by America‘s market leader in sanitation hose.
- Specially compounded to resist odour permeation.
- Lower cost, higher quality.
- Smooth white vinyl.
- Hard PVC helix for good flexibilityand bend radius.
- FDA approved for potable (iedrinking) water.
- Ideal for unpressurised freshwater tankfilling and ventilation hose lines.
- Can be used for bilge and generalpurpose applications whereappearance is important.
- Available in 3 sizes for manualtoilet discharge, electric toiletdischarge, and matching inletpipework.
|
|
| ... products without information |
| |
|
|
Boat toilet accessories
