|
|
Performance:
Max Volume:
50 GPM / 189 LPM
Suction Lift:
25ft / 7.6m / 23Hg
Discharge Head:
23ft / 7m / 10psi
Max Solids Size:
1.5" Dia.
Features:
Frame Size:
48"x15"x4" Extruded Aluminum
Durability:
Stainless Steel Transfer Cell - Powder Coated Aluminum Frame Frame-Oil Protected Air Pump.
Safety:
24V Push Button Controls with Shut Off Timer Included
Convenience:
Clean Out Access Cover, Clear Check Valves, Easy Access Control Panel
|
|
The Motor compressor VRK 200 R is complete with a handy folding drawbar and with a protection guard, which can be easily opened.
The START-WORK System allows safe starting even at low temperatures
Fuel consumption is low thanks to the innovative ECONOMY SYSTEM, i.e. the engine RPM acceleration system which automatically and progressively changes as a function of the air supply requested.
The 16 l capacity petrol tank is made of clear material. The operator can therefore easily check the fuel level. The petrol tank is easily removable with a retractable handle.
|
|
The MOTOCOMPRESSORE A90 670 is a wheeled compressor with a compact, easily transportable tank. A powerful piston provides the blasting unit with compressed air at an effective rate of 455 litres/minute so as to maintain a constant blast material outflow rate and allow the blaster to operate at maximum efficiency at all times without any pressure reload pauses.
Just 30 seconds after the motor compressor has been switched on the pressure has already been raised from 0 to 10 bar. The flow contains neither oil nor moisture.
This last aspect is particularly important when working with sodium bicarbonate because, in this case, if oil or moisture were to mix with the material the system could easily clog and work would have to be suspended to clean valves and nozzles.
|
|
Range mbar: 0 to 1300 mbar absolute
Overpressure: max 4 bar absolute
Resolution: 1 mbar
Accuracy: +/- 0.2% FS typical hysteresis and non-linearity
Connection: 6mm external, 4mm internal tubing
Display: Min, max, hold, tare, sea level-altitude correction
Units: mbar, bar, Pa, kPa, MPa, mmHg, PSI
Working temp: 0 to 50° C
Power: 9V battery included, additional power connector
Dimensions: 142 x 71 x 26mm sensor 11mm
|
|
Normal sensitivity: -80db/volt/microbar
Frequency response: 38 to 42 kHz
Display: Ten element bar graph
Audio output: 0 to 4 kHz
Power: 9V battery
Battery life: 15 hours continuous
Headset: Dynamic 32 ohm with volume control
Dimensions: 116 x 61 x 21 mm
Housing: Durable PVC/aluminium
|
|
Composite manufacturing processes such as resin infusion and vacuum bagging. The Vacmobile 20/2 is also an ideal vacuum source for most vacuum clamping and lifting duties.
The Infusion 20/2 system is complete with an integral resin trap and provides excellent performance from a compact package. All vacuum joints are very heavy duty to ensure vacuum integrity over a long working life. The machine's normal working height can be reduced to 602 mm (23.7") for transport in most station wagons, making it ideal for transport between different work locations or for off-site repair work.
|
|
|
VADS is the first direct-drive dry-running screw. With integrated speed controlling for demand-oriented applications and no need for a drive transmission, VADS is truly a Becker innovation! This unit is able to fulfil the highest requirements for a wide range of applications. By entering the load and output into your customer system, the air supply system automatically and directly adapts to the given requirements. The frequency-controlled drive unit offers a wide control range with optimised demand matching. In addition to energy savings and higher efficiency, this also results in lower maintenance requirements. The non-contact, oil-free screw unit ensures high air flows with low pulsation and lends itself to "master/slave" operation. Integrated accessories include a non-return valve, intake filter, sound absorbers and ventilation/bleed system. An air blast cooler is also available.
|
|
|
Simplicity of design with only one shaft and direct drive produces robust, long-lasting compressors with low maintenance and running costs. These compressors operate completely oil-free; the individual chambers are separated by long-life vanes. Already featuring integrated intake filters and control valves, these compressors can be fitted with other accessories without a problem. The blast-air cooler, which is also integrated, guarantees a very low blast air temperature. The compact cover ensures low noise and heat emission. Optional corrosion protection also makes these compressors suitable for extracting moist air.
|
|
|
Simplicity of design with only one shaft and direct drive produces robust, long-lasting vacuum pumps with low maintenance and running costs. These vacuum pumps operate completely oil-free; the individual chambers are separated by long-life vanes. Already featuring integrated intake filters and control valves, these vacuum pumps can be fitted with other accessories without a problem. The compact cover ensures low noise and heat emission. Optional corrosion protection also makes these vacuum pumps suitable for extracting moist air.
|
|
|
Simplicity of design with only one shaft and direct drive produces robust, long-lasting compressors with low maintenance and running costs. The vanes are sealed by the metered supply of oil delivered by oil pump. The integrated, efficient oil Separation System provides the capability of producing blast air that is virtually free of oil. The cover minimises noise emission and permits application even in difficult ambient conditions.
|
|
|
Simplicity of design with only one shaft and direct drive produces robust, long-lasting vacuum pumps with low maintenance and running costs. The vanes are sealed by the metered supply of oil. Already equipped with integrated non-return valves and an efficient oil Separation system, these vacuum pumps can be fitted with other accessories without a problem. The standard-featured circulating-oil lubrication System with integrated oil cooler and cover additionally minimise noise emission. Controlled by a float valve, the oil return suction system also makes these vacuum pumps suitable for use in rough-vacuum applications. Optional water cooling significantly prolongs the life of the oil, even in difficult ambient conditions.
|
|
|
Driven directly by an integrated frequency inverter, these pumps no longer require any drive transmission. The area in which the units work is 100% oil-free. The integrated speed governor optimises the use of energy by matching delivery to actual demand. This creates high efficiency levels and minimises energy consumption. Suction air remains pulsation-free all of the time. Various accessories, such as intake filter, non-return valve, sound absorbers as well as the air delivery and discharge system, are integrated in the completely soundproof cover structure.
|
|
The VADS 1500 is a direct drive, air-cooled, rotary screw unit housed in a sound enclosure. Because it is directly driven, there are no gear boxes needed to control the rotational speed. Due to the variable frequency controller, the pump operates over a wide range of speeds. This allows you to operate today at the lower frequency, and at a higher frequency tomorrow when your plant gets expanded, or you add equipment. If your load varies, so does the speed of the pump to maintain the proper flow or pressure.
Dry operation
Direct drive - No drive transmission
Variable speed controlled
2.1 speed regulation
Sound enclosure standard
|
|
|
Using "multi-stage" compression, side channel vacuum pumps generate low-pulsation suction air. Perfected impeller design with curved blades guarantees Optimum efficiency. Separation of the compression chambers on both sides of the impeller permits single-stage, twin-flow as well as two-stage, single-flow operation with only one impeller. Vacuum filter and vacuum safety valve can be integrated as an optional extra in the patented design of the sound absorbers. The sound absorbers can be varied in length, affording flexible adjustment to available installation space.
|
|
|
The sound insulation of our hoods is approx. 10-18 db(A). For better ventilation, our hoods are equipped with additional fans (1~ 230 V). These hoods are available as complete units including vacuum pumps (compressors) or equipped for retrofitting of your existing vacuum pumps (compressors).
|
|
Composite small-component manufacturing processes such as resin infusion and vacuum bagging.
This starter kit comes complete with an industrial vacuum pump, pump isolation valve, vacuum indicator gauge, in-line disposable filter and 5m of vacuum tubing.
|
|
As any other close mould method, infusion requires adapted means such as metering systems and reliable pumps. The reduction of measuring errors and wrong handling risks naturally leads toward the mechanisation of operations and the emphasised need for adequate equipment.
The polyester and epoxy machine range from Matrasur Composites offers all combinations necessary for infusion: injection under pressurised cover sheets, variable ratios, counting systems, among others.
|
|
| ... products without information |
| |
|
|
Boatyard : Compressors, Vacuum pumps
