|
|
|
Etch Primer is a pre-treatment primer for use on aluminium, galvanized steel, zinc-sprayed surfaces and lead. It provides an excellent key prior to the application of primers
|
|
A quick drying, high performance, two-component epoxy for application to sound gelcoats to help protect against osmosis.
Gelshield® is provided in two shades (green and grey) to ensure complete coverage.
Suitable for use in temperatures down to 5°C.
Coverage: 6m2/750ml 20.3m2/2.5lt
|
|
|
PO: One-pot polyurethane watertight primer formulated with DESMODUR® E resin to prevent osmosis on polyester. Easy to use and very watertight. P.O hardens by reacting with moisture in the air .
|
|
|
Nautix PE is a 2 pot high quality epoxy primer to protect polyester, steel and aluminium and to improve paints adhesion. Nautix PE is highly durable and resistant to abrasion.
|
|
|
|
|
|
|
Seawax Primer® is an « eco-designed » etch primer in aqueous phase. It is a mono-component product based upon a polyurethane resin.
It can be used on all sea boats or river boats.
This coating can be applied directly onto the substrate or onto existing coatings and offers very easy to apply conditions and short drying time.
Seawax Primer® applies to steel, aluminium, wood, iron, polyester (except polypropylene and polyethylene) boat bodies, under works, upper works and superstructures, to soft and rigid PVC beacon or mooring buoys in order to provide a strong antifouling and /or gloss paint.
Because it is both highly resistant and soft, it protects boat bodies against mechanical defects (cracks).
A deeper bright look is obtained through a satin-finish.
It improves adhesion to a substrate coated with an existing antifouling paint or a coating in poor condition.
A short drying time allows a shorter recovering time.
It is an ideal insulator that contributes to the waterproof of the substrate. Its original formula prevents or retards corrosion.
|
|
Awlgrip 545 Epoxy Primer-Base mixed 1:1 by volume with D3001.
Spray reduced 15-25% with T0006.
Brush reduced 0-20% with T0031. 2-3 mils (50-75 microns) dry film thickness/2 coats.
|
|
Interprotect® is a quick drying, easy to apply two-pack epoxy primer for high performance protection on all rigid substrates.
It's two-component application gives excellent anti-corrosive and abrasion resistance properties and it can be used equally above or below the waterline.
Coverage: 6m2/750ml 20.3m2/2.5lt
|
|
HPE: high built epoxy primer for polyester, steel and aluminium
|
|
Description:
A two-component etching primer, chemically drying by reaction of the mixed components and providing a temporary protection against corrosion and increasing the adhesive property of the subsequent coats.
Typical Uses:
As a pretreatment primer on nonferrous metals such as bronze & aluminium as well as zinc and galvanised iron. May also be used as pretreatment primer on blast-cleaned steel plates.
|
|
|
Mono-component, anchoring primer for fibreglass. Favours the anchorage of antifouling and monocomponent products on the new, grease-free gelcoat that was cleaned with a suitable wax remover (Sirio) to remove traces of wax and other greasy substances used in removing the fibreglass from the mould. The surface must be prepared before applying the product.
|
|
|
Nautix P1 is a conventional adhesion primer . P1 can also be used as a protective primer for wood and anticorrosion coating for steel.
|
|
OVERVIEW:
Rust-Oleum Marine Coatings Wood & Fiberglass Primer primes bare, lightly rusted and previously painted surfaces. Apply to wood or fiberglass surfaces above the waterline. Sands easily.
PRODUCT FEATURES:
- Fast-drying
- Durable, corrosion resistant
- Indoor/Outdoor
|
|
OVERVIEW:
Rust-Oleum Marine Coatings Metal Primer primes bare, lightly rusted and previously painted surfaces. Apply to surfaces above the waterline. Prevents chipping, cracking and peeling and eliminates the need for additional top coats and touch-ups.
PRODUCT FEATURES:
- Indoor/Outdoor
- Durable, corrosion-resistant
|
|
|
International Yacht Primer is a general purpose metallic grey primer for use on wood, steel and alloy above the water line only.
|
|
|
Selecting the right primer will protect your boat’s substrate, avoid early failure of a subsequent painting system and enhance your final finish. (Refer to choosing the right paint system)
|
|
|
Primer for bronze and light alloy propellers that does not contain chromium and is especially formulated to obtain optimum adhesion to difficult surfaces such as propellers and shafts. It can also be used on outdrives.
|
|
Elastic, yellow pigmented primer for soft- and hardwood, f. e. teak, pine, fir, larch-spruce etc.
Elastic, red pigmented primer for reddish wood, sensitive to light f.e. mahogany etc.
Elastic, brown pigmented primer for brownish wood f.e. oak
approx. 200 ml/m² per layer depending on the absorbency of the substrate
|
|
| ... products without information |
| |
|
|
Primers
