|
|
MARIN: Antifouing for fishing and cruising boats
|
|
Until now, antifouling paints presented problems with a transducer’s ability to provide accurate and reliable depth readings. Now there’s TranShield – the only antifouling paint specifically formulated to be safe and effective against barnacles on transducers of all sizes. Once applied, TranShield can withstand removal from water without affecting its performance.
|
|
|
Trilux 33 is a tin-free antifouling specifically formulated with Biolux Technology, to give highly effective antifouling protection in all waters for up to 18 months. It is suitable for use on aluminium craft, outdrives and outboards and any substrate where bright colours or a bright white antifouling is required.
|
|
Nautix A1
High quality antifouling for aluminium hull
|
|
A2 : antifouling for aluminium sailing boats
|
|
|
An insoluble matrix specific for protecting propellers, steel shafts and aluminium outdrives from marine fouling
|
|
Trilux Prop-O-Drev is a hard antifouling that is specially formulated for use on outdrives, outboard legs, propellers and sterngear.
- Aerosol spray is ideal for painting awkward shapes and difficult to reach areas
- Quick and easy application saves you time and effort
- Suitable for use on aluminium and stainless steel
|
|
Nautix A7 TSPEED:
antifouling for propellers and Z-Drive.
|
|
|
In the past, there was little you could do to protect underwater running gear. Clear Gear prevents barnacles and other marine growth from inhibiting aluminum out drives, outboard motors, lower units and propellers. Clear Gear keeps your running gear clean and allows you to take advantage of your vessel's maximum performance. No priming is needed. Just sand lightly, degrease and apply.
|
|
Product Description
VC®17m Extra unique thin film technology self-levels to create a super smooth surface without the need to sand and its quick drying nature allows fast over coating and re-launch times
Available in graphite, bright white and fluorescent orange (for safety markings)
VC®17m Extra graphite is not suitable for use on aluminium alloys and zinc sprayed surfaces
|
|
For fast power boats and racing boats
|
|
SEAJET SPEED FINISH is an environmentally friendly alternative to antifoulings with the following benefits:
- Keeps the underwater hull ultra-smooth and minimises hull friction for faster sailing and racing.
- Provides up to 3-years protection against fouling in both fresh and salt water environments.
- Contains no biocides and is not harmful to marine organisms.
- Fouling may loosely attach but is easily removed by water movement or washing.
- Brilliant colours available when applied over SEAJET SPEED BINDER COAT.
|
|
|
|
|
|
|
While not a breaking off innovation, this new generation of fouling release in aqueous phase treatment is one of the top last antifouling paintings.
It can be used on all sea boats or river boats.
Its main benefit is its innocuousness. It is a biocide-free and toxic solvent-free, therefore not hazardous for the aquatic environment and the human health.
The objective is to repel sea life without killing it.
«Seawax Fouling Release® » is mostly recommended for using on boat hulls : weight and water resistance, hydrodynamic trail are therefore reduced. Full consumption is also reduced and the hull requires less cleaning.
Its ingredients prevent and/or delay the fixation of microorganisms such as algaes, shells or shellfish and/or make it very unstable.
It brings its contribution to the preservation of sea life.
Also, there is a « self cleaning » effect when the boat sails, a water pressure is applied to the hull, all organisms then come off the substrate.
«Seawax Fouling Release® » is an alternative solution compared to actual paints, also innovative with obvious benefits for applicators.
Its technical features offer very easy to apply conditions and short drying time.
|
|
SEAJET 039 PLATINUM is a tin-free antifouling paint offering the ultimate in performance. Based on new SPC resin technology from Japan it is suited to all fouling environments and ideal for application to SUPERYACHTS and boats in the highest fouling areas. It is suitable for all types of boat, (except aluminium) even at speeds of up to 40 knots. Advantages include:
- Ultimate performance offering equivalent performance to tin (TBT) based antifouling
- Suitable for all boats up to a speed of 40 knots
- Apply extra coats for up to 3 years protection
|
|
|
Awlstar Gold Label is a self polishing antifouling used to deter fouling growth, ensuring the ultimate underwater protection for both power and sailing yachts.
|
|
The ultimate performer in eroding antifoulings. Includes revolutionary activator and new resin system for unparalleled effectiveness over a full season. Solvent free for easier clean-up.
Contains Copper Oxide and Zinc Pyrithione
|
|
|
Formulated with Biolux® Technology for controlled optimised biocide release. Micron® Extra does not contain organotin biocides and complies with the IMO Antifoulings Systems Convention (AFS/CONF/26) %u2013 Lloyds Register certificate number MNDE/2002/1216
|
|
Nautix A3 :
High quality selfpolishing antifouling
for yacht and motor boats (under 30 knots speed)
|
|
Cukote’s high loading of cuprous oxide makes this formulation a top performer, even in the most severe fouling areas. As an ablative, self-polishing coating, there is no buildup of paint over time. Your hull's underwater surface remains smooth and clean. Cukote copolymer can also withstand removal from water without affecting its antifouling properties.
|
|
|
|
|
|
|
Coppercoat is based on a water miscible epoxy resin, which is
heavily loaded with pure grade (99%) fine copper powder and a mix of biocides. When fully cured, this hard wearing epoxy treatment, which contains no banned compounds and is fully certified by the Health and Safety Executive (No. 7532), forms a durable coating that offers
exceptional long term resistance to marine fouling.
When correctly applied, this long life epoxy treatment should continue to deter marine fouling for many years, the annual chore of repainting associated with conventional antifoulings, is no longer necessary.
Damaged areas can be touched up as required. If, over the
months, a slight accumulation of slime does appear, this can be removed by pressure washing or brushing.
An annual wash or brush is recommended.
Eventually, after several years, the surface may need to be lightly abraded with a fine grade of "wet and dry" paper to expose fresh copper.
For more information have a look at www.coppercoat.com or ask for our specifications and prices.
|
|
|
Highly effective, long life antifouling, free from organostannic toxins, with a high content of a special copper salt. Thanks to its special formula, it protects wood, steel and fibreglass hulls for many seasons.
|
|
|
No longer just extra strong, a new, improved formula makes this superior antifouling ultra strong. It is ideal for high-speed crafts or craft on drying moorings. Can be burnished. Contains Biolux which is exclusively available in antifoulings from International.
|
|
Hard matrix antifouling for fast power boats, sailing boats or leisure fishing boats
|
|
OVERVIEW:
Rust-Oleum Marine Coatings Boat Bottom Antifouling Paint releases copper to prevent the buildup of barnacles, algae and other marine growth. Apply to fiberglass, wood or steel surfaces below the waterline. Works in fresh or salt water.
PRODUCT FEATURES:
- Protective coating for use below the waterline
- For mild to moderate fouling conditions in both fresh and saltwater
|
|
AF-33 has been re-formulated to be a harder more durable finish for all types of vessels – from workboats to daysailers. Its formula is effective in performance for a single season. Lower cost saves money.
|
|
Sharkskin is Sea Hawk's traditional 45.2% copper-based hard modified epoxy paint. Sharkskin aggressively combats all types of marine fouling including barnacles, seagrass, green weed, and other fouling organisms in fresh and saltwater. Sharkskin can be applied over most antifouling coatings.
|
|
Sea Hawk's top-of-the-line conventional antifouling paint contains over 75% cuprous oxide. This multi-season bottom paint aggressively combats ALL types of fouling and reduces hull maintenance with year-round, trouble free performance. Superior adhesion to fiberglass, wood and steel hulls makes it ideal for any vessel. Use for overcoating, without the fear of lifting.
|
|
Tropikote with Slime Resistance is a hard protective paint which produces the most durable finish for long lasting performance.The high loading of cuprous oxide combined with a specially formulated algaecide results in unprecedented resistance to barnacles, algae, slime and other marine and fresh-water fouling organisms. It can be applied over most hard antifouling coatings.
|
|
SEAJET 037 COASTAL is a hard, tin-free antifouling paint suitable for all types of pleasure craft
Advantages include
- Suited to all vessels, from yachts to fast motorboats
- Eco-sensitive and meets all environmental requirements.
- Good performance in coastal and inland waters and at an economical price.
- Suitable for drying moorings.
|
|
|
|
|
|
|
Classic Antifouling
• Self-polishing, for sail and pow er boats (< 40 k nots), except aluminium hulls.
• Moderate fouling areas.
• Suitable for drying berths.
• Good compatibility.
• Coverage ratio : 10 m 2 /litre.
• Minimum temperature during application : + 5°C.
In 20°C ambient temperature, w ait 2 ½ hours before overcoating
and 4 hours before launching.
Performance antifouling
• High performance, with gradual polishing ratio, for sail and power boats (< 40 knots), except aluminium hulls.
• High fouling areas.
• Suitable for drying berths.
• Good compatibility.
• Coverage ratio : 8.80 m2/litre.
• Minimum temperature during application : + 5°C.
In 20°C ambient temperature, wait 2 ½ hours before overcoating
and 4 hours before launching.
Racing antifouling
• Ultimate performance self-polishing antifouling, ideal for serious racers and fast powercruisers (< 70 knots), except aluminium hulls.
• Very high fouling areas.
• Very bright colours.
• Sandable, suitable for drying berths.
• Good compatibility.
• Coverage ratio : 11.20 m2/litre.
• Minimum temperature during application : + 5°C.
In 20°C ambient temperature, wait 2 ½ hours before overcoating
and 4 hours before launching.
|
|
|
|
Anti-foulings
