|
|
|
Webasto fan-type heat exchangers are available in various ratings and can therefore be matched to any size of cabin. In this way, you can create your own customized comfort zone in each cabin.
|
|
AT-DC model air handlers are draw-through (ducted) units specifically designed for use in marine chilled water systems. The ultra quiet blower has a brushless DC motor that has a wide speed range with virtually no hum at low motor speeds. Draw-through air handlers can be installed in a locker, under a bunk, or overhead, with conditioned air ducted to a discharge grill placed high in the cabin.
Typically each cabin or area has one or more air handlers with an independent climate control to provide the user with the most comfortable environment on the water.
*All Dometic air handlers use corrosion-resistant materials, and are fully insulated with deep drain pans to prevent secondary condensation
*AT models have an integrated chassis with vibration isolation mounts and a rotatable blower
*Can be used with Marine Air microprocessor or mechanical controls
*Copper tube/aluminum fin water coils are designed for hot/humid marine environment
*Integrated 3-way bypass valve standard
*Sloped drain pan with anti-slosh, antifungal foam
*Includes washable air filter; Micro-particle filters available
*Optional electric heater with 2-stage overload protection
*Optional modulating flow control recommended on large systems to ensure proper water distribution
|
|
E-FD remote evaporators are draw-through, ductable, DX air handlers incorporating variable-speed blowers and integral water-displacing condensate pans. Each unit is pre-charged, test run in all operating modes, and leak checked prior to shipping. E-FD units are ductable and designed to be installed in low cabin areas (under berths, lockers, etc.) and ducted to high supply air grilles.
These units have rotatable blowers providing flexibility to fit specific space requirements and allowing for proper duct work installations. Transition boxes may be used to supply air to more than one area from a single unit.
When choosing the proper model E-FD DX Air Handler, primary consideration should be given to calculated BTU loads and available power supply. A refrigerant line set is required to connect the E-FD to the Marine Air CS condensing unit.
*The unique compact modular design incorporates large plenum chambers for maximum efficiency
*Condensate drain pans are insulated to prevent sweating and have two FPT drain connections
*Quiet, efficient, centrifugal blowers have fully insulated housings
*Large blower inlets provide maximum air flow across evaporator coils
*Charge Guard protection provides sealed access ports, ensuring environmental protection and system integrity
|
|
AT model air handlers are draw-through (ducted) units specifically designed for use in marine chilled water systems. Draw-through air handlers can be installed in a locker, under a bunk, or overhead, with conditioned air ducted to a discharge grill placed high in the cabin. Typically each cabin or area has one or more air handlers with an independent climate control to provide the user with the most comfortable environment on the water.
All Dometic air handlers use corrosion-resistant materials, and are fully insulated with deep drain pans to prevent secondary condensation. AT models have an integrated chassis with vibration isolation mounts and a high-performance, rotatable blower.
*Can be used with Cruisair microprocessor or mechanical controls
*Copper tube/aluminum fin water coils are designed for hot/humid marine environment
*Integrated 3-way bypass valve standard
*Sloped drain pan with anti-slosh, antifungal foam
*Includes washable air filter; Micro-particle filters available
*Optional electric heater with 2-stage overload protection
*Optional modulating flow control recommended on large systems to ensure proper water distribution
|
|
Cruisair RE model DX air handlers are draw-through (ducted) units designed to be used with Type R remote condensing units. They are typically installed under a settee or bunk, or in a locker, with air ducted to a discharge grill high in the cabin. They are available in sizes from 4,000 to 36,000 BTU/hr (1.2kW to 10.5kW). Corrosion-resistant materials are used throughout, and the unit is fully insulated to prevent secondary condensation.
*Deep, positive-flow drain pan with anti-slosh, anti-fungal liner.
*Copper tube/aluminum fin evaporator coils are designed for hot/humid marine environment.
*Washable air filter included.
*Micro-particle filters available.
*Includes mounting kit with vibration isolators.
*Optional high-velocity blowers on REU models provide increased airflow and lower noise.
|
|
Mermaid's Dry-Pal Dehumidification units are an ideal addition to any vessel, camper, or RV, where dehumdification is a must. This product can be used instead of using your air conditioning system. Manfufactured out of 304- 18 gauge polished stainless steel. The Dry-Pal is available in 110v or 220v applications. This product is designed to dehumidify an area 250-350 cubic feet. It will dehumidify larger areas, however, optimal humidity
levels will be more accurately achieved within the units parameters. Non-skid rubber feet are installed on each unit for the security of not damaging counter tops or tables. Ideal location for the unit is in an area where no air obstructions can occur. It is preferred on or near a sink or table where a drain can be utilized. The condensation that is accrued needs to drain to either an overboard thru-hull or a sump pump. Dry-Pal is protected with the security of a one-year warranty. 6 feet of clear 1/2 condensation hose provided.
|
|
| ... products without information |
| |
|
This 300 bar (4350 psi) pressure gauge is a small model that will not be in the way during the dive. Made of robust metal. With Poseidons 300 bars kevlar hose.
|
|
AP508A Miniature Pressure Gauge
Designed for divers using off-board gas cylinders this superb mini gauge eliminates the clutter of conventional hoses & gauges. The AP508A screws directly into the regulator's 1st stage HP port (7 / 16" UNF thread).
0-350 Bar markings are black against a white face for optimum clarity.
|
|
Halcyon's standard DIR Pressure Gauge is just what you would expect in a DIR SPG: low tech, reliable, and accurate. The classic heavy-duty brass housing and tempered glass lens will stand up to any environment, and the gauge face is clean and easy to read in all conditions. The weight and size of the gauge makes it best suited to serve as a primary SPG for your back gas.
|
|
Mechanism: spiral (Patented)
Module: stamped and chrome platted brass
Hose: Hi-resistant HP hose
Thread: male 7/16" female 7/16"
Hose length: 800 mm
Face: luminescent
Glass: Hi-resistant Polycarbonate
Range: BAR 0 - 400 (10 bar increment)
Certified CE EN 250
|
|
With two-gas switching Nitrox, Air, and Gauge modes, this airintegrated computer delivers everything you need to maximize bottom time and make the most of every dive.
|
|
| ... products without information |
| |
voltage : 220 voltes
power : 1500 litres/mn
pressure :250 mbar/3,6psi
|
|
- Inflates a 4 man dinghy in 1-2 minutes
- Supplied with an adaptor for all major inflatable boats
- Deflates a dinghy flat and ready to pack
- One handed operation
- Airflow 550L / Minute
- 25 Amps Max
|
|
Hi-Speed inflator deflator
The high speed is a high quality unit for the rapit inflation and deflation of all inflatables. Inflates a typical four man dinghy in as little as one to two minutes. Adjustable nozzles have been included for most inflatables and valve types.
|
|
This 110-volt pump will inflate or deflate your inflatable in a hurry. It comes with an assortment of nozzles to adapt to your needs and has a high-volume, low-pressure output to get the job done quickly.
|
|
2.2 lbs/cu ft (35.2 kg/cu m) closed-cell polyethylene (PE) foam
Natural color (off-white)
Water absorption:
Less than 0.3 lbs/sq ft exposed (1.5 kg/sq m)
Less than 3% by volume
Per ASTM D3575-Suffix V, EN 28301, ISO 2581 tests
Buoyancy: 58 lbs/cu ft (930 kg/cu m)
Completed foam sections heat-welded (not glued) and hot-wire shaped to finished profile
|
|
CPI's air collar is constructed of 100% polyurethane (PU) for its outer cover and contains our patent-pending removable bladders constructed of urethane film.
The collar is outfitted with stainless steel D-rings for tie downs and lifelines. Our collars are built to the customer's specs and can include a variety of trim packages.
Standard rope strips or custom attachment methods are available and can be configured to the customer's specs.
|
|
| ... products without information |
| |
Racor now offers replacement filters for marine applications. These filters are direct replacements for the intake air filter portion of vairous brands of air filters/silencers
|
|
Eliminate Fuel Vent Line Overflow During Refueling
Next time you fill up, watch your fuel vent line. A typical refueling will send up to a half gallon or more of fuel spilling overboard. Fuel spillage is not only expensive, it's absolutely deadly to fragile lakes, rivers and waterways. USCG and other regulations prohibit the discharge of oils including civil and criminal penalties.
Installed in the fuel tank vent line, the Racor Fuel/Air Separator efficiently separates air from fuel forced into the line. Air is vented, and all fuel is returned to the tank. The Fuel/Air Separator captures fuel normally discharged due to agitation and thermal expansion up to 2.4 PSI. It also eliminates damage to expensive striping and labels and protects finishes from fuel stains. The unit is maintenance free -- there's nothing to rust or corrode.
The Racor Fuel/Air Separator fits neatly into your vent line, actually replacing a section of the line. One Fuel/Air Separator unit is required for each vent line, both models fit 5/8" vent lines. Fittings are included.
|
|
To check the pressure in the cylinder
Supplied with a screw purge
Available with yoke or DIN 300 Bar or M26 x 2 ISO 230 bar (Nitrox/O2) connections.
|
|
| ... products without information |
| |
|
|
see the results for the following category
