|
|
Macerator Pump
The TA3P10-19 macerator pump takes care of toilet waste. A rotary cutter shreds waste before it is pumped into or out from the holding tank. The pump should be connected as close as possible to the holding tank discharge outlet or the bowl discharge outlet. Note! Use unbleached lavatory paper only.
|
|
The sewage pump M is a self-priming diaphragm pump. It works without a macerator. Even bigger solids can be conveyed without damaging the pump because of the lip valves which have been installed. The self-locking valves make the pump non-reactive, i.e. it can be mounted to the side standing, hanging or sideways. The intake and discharge bent is revolving. This is necessary for better connecting possibilities of the suction and pressure hoses. The suction and pressure connections usually go from left to right. They can easily be changed, if the suction way should go from right to left or from the bottom to the top. All parts which come into contact with water can be ordered in red brass or aluminium. The pump can be delivered with a 12 V or 24 V motor.
Continuous operation 1 – 2 hours max.
Attention: The cross section of the pipe should never be less than 1 ½”/ 38 mm – or the pump capacity will not be achieved.
|
|
|
The Rheinstrom sewage pump FS 370 is a big, very hard wearing macerator pump which is suitable for continuous operation. It is not self-priming and therefore it must be installed either at the lowest part of the tank or lower than the tank itself. A macerator which chops up the conveying means is mounted in front of the pump. In case maintenance has to be carried out the pump’s body can easily be taken apart. In contrast to the sewage pump F the sewage pump FS 370 is suitable for continuous operation. Sewage tanks up to a size of 1 m³ are ideal for this pump.
|
|
|
|
|
|
|
WASTE EVACUATION
The Jabsco 18590 series DC macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operation
It is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage.
FISH BOX AND LIVEWELL TANK EVACUATION
The Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties.
Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats.
|
|
|
SHURflo’s Macerator pump is designed specifically for sanitation waste and fish box evacuations providing superior performance in harsh marine environments.
|
|
|
SHURflo’s Macerator pump is designed specifically for sanitation waste and fish box evacuations providing superior performance in harsh marine environments.
|
|
- Self-priming to a lift of six feet
- Flow rate to 6-1/2 gallons per minute
- Rated for continuous duty cycles of up to 1/2 hour ofuninterrupted pumping time (nearly 200 gallons ofsewerage transfer per cycle)
- Motor meets USCG regulation 183.410 and ISO 8846MARINE for ignition protection
- Motor is EMC compliant and CE marked
- Ports accept 1-1/2" hose with room for double bandclamps
- All pump components (non-flexible) are non-corrosiveplastic, stainless steel and bronze
- Diaphragm is made of Santoprene and the valves aremade of nitrile
- Pump housing is made of glass filled nylon
- The motor and gear drive are painted with a durableprotective coating
- A plastic motor splash guard adds additional protection
|
|
|
SANISPLIT is an automatic soil and waste water pumping unit, which collects the water from the kitchen and bathroom and pumps it into the collection tanks, even without the necessary gradient. SANISPLIT includes a powerful and silent centrifugal pump controlled by a pressure switch, which starts the pump as soon as the water arrives in the unit's collection tank.
|
|
Aqua Jet WPS 2.4, 2.9, 3.5, 4.0 & 5.2 - Aqua Jet Water Pressure Systems
The five chamber Aqua Jet WPS-series provides a reliable heart for small boat and recreational vehicle water pressure systems. Compared to conventional three or four-chamber diaphragm pumps, the Aqua Jet demonstrates dramatically lower noise and water pulsation characteristics.
It is recommended to install the WPS-pumps with an accumulator tank. Always use a PUMProtector inlet strainer before the pump intake.
|
|
Aqua Jet Flow Master 5.0 WPS
The ideal choice for pressurizing water in a closed system. The digital controller adjusts water flow as the demand is increased and decreased while maintaining a very smooth flow. The unique variable flow feature of the Flow Master pump allows the pump to be mounted without an accumulator tank and still maintain an even flow regardless if one or multiple taps are being used.
|
|
Aqua Jet Uno WPS 3.5 & 5.2
Medium demand unit with a single Aqua Jet WPS capacity 13 l/min or 20 l/min fixed on a base with PUMProtector inlet strainer and a 2 litres pre-pressurized accumulator tank.
Aqua Jet Duo WPS
High demand unit with two parallel-connected Aqua Jet WPS capacity 40 l/min fixed on a base with PUMProtector inlet strainers and a 2 litres pre-pressurized accumulator tank.
Aqua Jet Uno Max WPS 2.9 & 3.5
Medium demand unit with a single Aqua Jet WPS with capacity 11 or 13 l/min fixed on a wooden panel for easy and efficient installation. The unit includes a PUMProtector inlet strainer and a 2 litres pre-pressurized accumulator tank.
|
|
Features:
%u2022 Integrated pump and tank system
%u2022 May be mounted vertically or horizontally
%u2022 Flow rates up to 4.5 US Gallons/min (17 Lires/min)
%u2022
Specifications:
Voltage Options 12,24,32 & 115v
Flow Rate Flow rates up to 4.5 US Gallons/min (17 Lires/min);
Max. Pressure 40psi (2.8bar)
Port Type 1/2" hose barb
Strainer Included
|
|
• Integrated pump and tank system
• May be mounted vertically or horizontally
• Flow rates up to 4.5 US Gallons/min (17 Lires/min)
|
|
| ... products without information |
| |
Genuine Sherwood Impellers can be identified using their overall dimensions.
8000K - width 3/4" diameter 1-9/16"
09000K - width 7/8" diameter 2-7/16"
09959K - width 1-1/4" diameter 2-7/16"
10077K - width 25/32" diameter 2-1/4"
10615K - width 1-5/8" diameter 2-9/16"
15000K - width 2" diamter 2-9/16"
17000K - width 2-7/8" diameter 3-5/16" (keyed shaft)
18000K - width 4" diameter 3-3/4"
22000K - width 4-5/16" diameter 4-1/2"
26000K - width 3-1/8" diameter 3-3/4"
27000K - width 2-7/8" diameter 3-5/16" (splined shaft)
|
|
Take good care of the cooling system – change to a new impeller every year!
The impeller is a very important security device. Its task is to pump the water through the cooling system of the engine. But remember that the impeller should be replaced every year. And always make sure you get a Johnson Pump Brand original impeller. Then you’ll know that it matches your pump exactly.
Remove the impeller with a slip joint plier or an Impuller.
|
|
Impeller removal has been made easier with the patented Sherwood Impeller Puller. Simply thread the puller into the threaded end of select Sherwood impellers and the bolt presses on the shaft, pushing the impeller out of the pump.
Sherwood's Impeller Puller is utilized on five different impeller sizes. Impeller puller 23631 is used on the 17000, 18000, 22000, and 27000 impellers. Impeller puller 24412 is used on the 27000 impeller.
|
|
|
The sound insulation of our hoods is approx. 10-18 db(A). For better ventilation, our hoods are equipped with additional fans (1~ 230 V). These hoods are available as complete units including vacuum pumps (compressors) or equipped for retrofitting of your existing vacuum pumps (compressors).
|
|
|
The sound insulation of our hoods is approx. 10-18 db(A). For better ventilation, our hoods are equipped with additional fans (1~ 230 V). These hoods are available as complete units including vacuum pumps (compressors) or equipped for retrofitting of your existing vacuum pumps (compressors).
|
|
Mimic panel X for navigation lights and bilge pump control for motor yacht.
|
|
| ... products without information |
| |
This greywater transfer station - GWH works automatically.
The system is designed to be connected to showers, wash basins, kitchen sinks and all places where waste water can not run with the help of natural fall. The system consists of a durable collecting vessel, available in polyethylene (PE) or in stainless steel. At the front 2 inlet pipes 1” and 1 ½” and a ventilation connection ½” can be found. The discharge pump is our hard-wearing waste water pump F. On the inside of the collecting vessel there is a float switch. Due to the use of a pump with cutting wheel hair and kitchen leftovers are chopped and conveyed without any problems. The arising waste water is disposed via a pressure pipe (1”). The integrated pressure lip valve contains a safety valve which prevents a flow back of waste water. The station works up to a tilt angle of 45°.
|
|
The SCHOTTEL Pump-Jet (SPJ) operates on the principle of a centrifugal pump. An impeller sucks in water from under the hull and forces it into a pump housing. The outlet nozzles are fitted in the bottom plate, making it possible for the jet to be installed in a flat-bottomed hull too.
With a compact design, low loss of buoyancy and low suction effect, Pump-Jets with power ratings up to 3500 kW develop a high thrust even in extremely shallow water and over a wide speed range. Like all SCHOTTEL products, they are distinguished by their excellent manoeuvring properties - as propulsion units for inland and coasting vessels or as independent manoeuvring and standby systems for seagoing ships.
|
|
AirV - Extra Heavy Duty Radial Blowers
Marine ventilation blowers that are designed for engine compartment ventilation prior to start up. AirV heavy duty blowers are designed for continuous duty and can therefore be used for air intake or extraction in bilges, galleys, accommodation and other compartments.
|
|
|
|
