|
|
The Johnson Pump for boat TA3P10-19 Macerator pump takes care of the toilet waste, shredding it before it is pumped into or out from the marine holding tank.
Features
- Ignition protected motor, conforming with ISO 8846 Marine
- Mounting bracket for easy replacement
- Extremely energy efficient
- Rotary cutter for boat casing of PET (thermoplastic polyester)
- Directly connected to sewage line or holding tank for boat |
|
Specially engineered to greatly reduce sound emissions, SeaLand vacuum generators for boats open new installation options for boatbuilders and renovators. Low-profile vacuum generator allows use in a wide range of hulls. Separate vacuum pump for boat and tank for boat components also add installation versatility.
|
|
- Self-priming to a lift for boat of six feet
- Flow rate to 6-1/2 gallons per minute
- Rated for continuous duty cycles of up to 1/2 hour ofuninterrupted pumping time (nearly 200 gallons ofsewerage transfer per cycle)
- Motor meets USCG regulation 183.410 and ISO 8846MARINE for ignition protection
- Motor is EMC compliant and CE marked
- Ports accept 1-1/2" hose with room for double bandclamps
- All boat pump components (non-flexible) are non-corrosiveplastic, stainless steel and bronze
- Diaphragm is made of Santoprene and the boat valves aremade of nitrile
- Pump housing is made of glass filled nylon
- The motor and gear drive are painted with a durableprotective coating
- A plastic motor splash guard adds additional protection |
|
WASTE EVACUATION
The Jabsco 18590 series DC macerator pump for boats unit is the ideal solution for emptying marine marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operation
It is recommended that holding marine tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage.
FISH BOX AND LIVEWELL TANK EVACUATION
The Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case for boats gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties.
Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports marine fishing boats. |
|
These are the ultimate sewage handling diaphragm pumps for boats. They get tough jobs done quickly, quietly, and reliably. Ideal for holding tank for boats discharge applications, transfer systems, and for batching sewage into our Tidal Wave Type II MSD's. These pumps are an engineer's dream with their rugged construction and non-clogging flow-through design.
They make a great emergency bilge pump for boat and are also ideal for industrial applications such as ground water remediation, abrasive fluid transfers, and dewatering.
|
|
| The Rhine current diverter boat pump telex 370 is a large, expresses robust and chopper pump suitable for the permanent run. It is not sucking in and must be cultivated by from there either in the deepest place of the tank for boats or be installed more deeply than the tank. A chopper is before-built for the actual pump part, which cuts the material to be conveyed up very finely. In case for boats of maintenance the pump body can be divided very easily and with simple means. Contrary to the diverter pump F it is suitable for continuous operation. From there it Fäkalientanks up to a size of approx. 1 m ³ are ideal for this pump. |
|
| This new feature makes accidental run-dry impeller damage a thing of the past |
|
| Flexible impeller boat pumps make excellent marine bilge pumps, principally because of their ability to handle bilge debris without damage. Because of the robust design many owners still use our 12 Volt dc or 24 Volt dc flexible impeller motor pump units that are up to 25 years old! Flexible Impeller Pumps also give the benefits of good flow, low cost, low size and weight, and are easily serviced and maintained. Most Flexible Impeller pumps must not be run dry, as this will damage the impeller which will require replacing. However, the Utility Puppy 2000 and 3000 both allow maximum of ten minutes dry running after initial prime. As with submersible pumps, flexible impeller pumps can be operated using a float or Hydro Air switch for boat, and remotely controlled from outside the bilge compartment. There is a wide range of flexible impeller pumps to choose from giving a range of flows, discharge heads, and self-priming options for a wide variety of applications such as ballast transfer, bait tank circulation, and deck wash duties |
|
FB-8 series Multipurpose Compact Heavy Duty Bronze Impeller Boat pumps
Compact design, raw water resistant pumps at an attractive price. With excellent self-priming capability, these pumps are ideal for applications like engine for boat cooling, bilge pumping, wash-down, refuelling, emergency and fire fighting.
Also ideally suited for shore for emptying septic boat tanks, flushing, cleaning and filling boat water tanks. |
|
Flow rate: 32 Litres/min (6.5 gallons/min)
Self-priming from dry up to 1.2m (4ft)
- Small bilge debris present no problem to these bronze bodied, flexible impeller boat pumps.
- Simple design means fewer wearing parts.
- ISO 8846 MARINE (Ignition protection).
- ISO 8849 MARINE (Bilge pump for boat standard). |
|
| The alternate marine pump is available in single speed or two speed with auto shift model; and we can also propose the rotating model, powered by an universal marine winch handle |
|
Engine for boats Cooling Boat pumps
Flexible impeller pumps are self-priming and therefore, are ideal for engine cooling, wash-down, circulation, and many general purpose on-board or dockside applications. The bronze bodies and stainless steel shafts are well situated for marine environments. They can operate in either rotational direction.
|
|
| The RHEINSTROM Impellerpumpe IP 50 can be used for the promotion of drinking water or waste water. The parts coming with water into contact are made of stainless material. The pump for boats is positioninsensitive. It is sucking in drying. A longer unlubricated operation should be avoided however, since otherwise the Impeller could suffer damage. The pump is available in 12 V and 24V execution. |
|
| ... products without information |
| |
HYDRAULIC HELMS
The hydraulic helms are of the axial pistons type. The helm housing is in aluminium with bronze gears and cylinder marine block for greater durability and longer life. The P20, P30 and P42 models are supplied with a built-in non return and relief valve. For all the other models a non return valve shall be mounted separately. The hydraulic helms are supplied without any fitting. Complete kit of fittings are available separately, which shall be specified when placing the order. The codes and descriptions of the different marine kits can be found on the price list. |
|
| The hydraulic helms are of the axial pistons type. The helm housing is in aluminium with bronze gears and cylinder block for boat for greater durability and longer life. The P20, P30 and P42 models are supplied with a built-in non return and relief valve. For all the other models a non return valve shall be mounted separately. The hydraulic helms are supplied without any fitting. Complete kit of fittings are available separately, which shall be specified when placing the order. The codes and descriptions of the different marine kits can be found on the price list. |
|
Reliable operation of a steering system depends upon the quality and performance of the helm pump. The Jastram "H" series manually operated helm is a precision made axial piston pump specifically designed to operate effectively at a very slow turning rate.
The H60, 90 and 110 are among the largest helm boat pumps made and provide excellent primary or backup steering for large steering systems for boats. |
|
Reliable operation of a steering system depends upon the quality and performance of the helm pump for boat. The Jastram "H" series manually operated helm is a precision made axial piston pump specifically designed to operate effectively at a very slow turning rate.
The H26/36/58 provide excellent primary or backup steering for small and relatively large marine steering systems. |
|
| ... products without information |
| |
| ... products without information |
| |
| ... products without information |
| |
| ... products without information |
| |
|
|
see the results for the following category