|
|
Flow rate: 13.7-16.3 Litres/min (3.7-4.5 gallons/min)
Self-priming from dry up to 2.4m (7.8ft)
- Variable Speed Control
- Solid State Pressure Sensor
- Nearly Silent Operation / No Cycling
- Operates on 12V DC or 24V DC
- Controls Pressure by Changing Motor Speed
- Speeds Up As Demand Increases
- Self-priming / Runs Dry
- No Accumulator Tank Needed
- CSA Listed / EN ISO 8846 Marine / C.E. Certified
- Protected under U.S. Patent #6,607,360
- Includes Inlet Strainer
|
|
Features:
- Smooth flow
- Dry running capability
- Soft noise absorbing mounts
- Snap-fit port fittings
- Built-in bypass -less pulsation
- Reduces need for accumulator tank
- Corrosion resistant materials
- CSA listed
- ISO 8846 MARINE (ignition protection)
- CE
|
|
Features:
- Smooth flow
- Dry running capability
- Soft noise absorbing mounts
- Snap-fit port fittings
- Corrosion resistant materials
- Meets USCG Regulation 183.410 and ISO 8846 MARINE (ignition protection)
- Meets EN 50081-1 Electro-magnetic Compatibility
|
|
|
QL Water Pressure Pumps for water supply to the galley and shower - you just turn the tap or taps and the water flows. The water pressure pumps are suitable not only for fresh water but also for salt water.
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 12.5 litres/min (3.3 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 12.5 litres/min (3.3 US gallons/min)
|
|
Features:
- Flexible installation
- No filter required
- Compact and simple design
- Dry running capability
- Relevant Standards: ISO 8846 MARINE and USCG Regulations for Ignition Protection ISO 8849 MARINE Bilge Pump Standard
- Built to ISO 15083 Specification
- Meets BSEN 50081 (Electro Magnetic Compatibility)
|
|
|
|
|
|
|
WASTE EVACUATION
The Jabsco 18590 series DC macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operation
It is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage.
FISH BOX AND LIVEWELL TANK EVACUATION
The Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties.
Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats.
|
|
|
SHURflo’s Macerator pump is designed specifically for sanitation waste and fish box evacuations providing superior performance in harsh marine environments.
|
|
|
SHURflo’s Macerator pump is designed specifically for sanitation waste and fish box evacuations providing superior performance in harsh marine environments.
|
|
- Self-priming to a lift of six feet
- Flow rate to 6-1/2 gallons per minute
- Rated for continuous duty cycles of up to 1/2 hour ofuninterrupted pumping time (nearly 200 gallons ofsewerage transfer per cycle)
- Motor meets USCG regulation 183.410 and ISO 8846MARINE for ignition protection
- Motor is EMC compliant and CE marked
- Ports accept 1-1/2" hose with room for double bandclamps
- All pump components (non-flexible) are non-corrosiveplastic, stainless steel and bronze
- Diaphragm is made of Santoprene and the valves aremade of nitrile
- Pump housing is made of glass filled nylon
- The motor and gear drive are painted with a durableprotective coating
- A plastic motor splash guard adds additional protection
|
|
|
SANISPLIT is an automatic soil and waste water pumping unit, which collects the water from the kitchen and bathroom and pumps it into the collection tanks, even without the necessary gradient. SANISPLIT includes a powerful and silent centrifugal pump controlled by a pressure switch, which starts the pump as soon as the water arrives in the unit's collection tank.
|
|
| ... products without information |
| |
|
|
