|
|
|
Self-priming pump, fitted with neoprene rotors; watertight in accordance with ISO 8846 standards (may be installed on the engine room) - Version A: Electrophoresis enamelled engine casing - Version B: Model MKII fitted with pump unit made of resin-thermosetting reinforced fibre glass + stainless steel internal inserts.
|
|
Ideal for Twin Inboard / Single Generator boats either Gas or Diesel
Also applicable for Single Diesel Engine / Transmission and Generator (trawlers, sailboats, work boats)
Enclosed in a molded housing provided excellent engine room presentation
Mounting plate for easy engine room installation
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps water, oil and diesel fuel
Built in fuse for motor protection
|
|
- Self-priming to a lift of six feet
- Flow rate to 6-1/2 gallons per minute
- Rated for continuous duty cycles of up to 1/2 hour ofuninterrupted pumping time (nearly 200 gallons ofsewerage transfer per cycle)
- Motor meets USCG regulation 183.410 and ISO 8846MARINE for ignition protection
- Motor is EMC compliant and CE marked
- Ports accept 1-1/2" hose with room for double bandclamps
- All pump components (non-flexible) are non-corrosiveplastic, stainless steel and bronze
- Diaphragm is made of Santoprene and the valves aremade of nitrile
- Pump housing is made of glass filled nylon
- The motor and gear drive are painted with a durableprotective coating
- A plastic motor splash guard adds additional protection
|
|
The Mach5 water pressure system from Headhunter represents a next quantum leap in pump technology with many advanced features and improvements over conventional water pressure pumps.
An integrated control system provides instant dry run protection, and allows the pump to be used with or without a pressure accumulator tank. The Mach5 incorporates a state-of-the-art multistage impeller system driven by a super-efficient water-cooled motor to generate up to 20 gallons per minute, instantaneously, on demand, and in virtual silence. An easy to read control panel on top of the pump provides instant visible status information as well as reset capability.
|
|
Flow rate: 13.7-16.3 Litres/min (3.7-4.5 gallons/min)
Self-priming from dry up to 2.4m (7.8ft)
- Variable Speed Control
- Solid State Pressure Sensor
- Nearly Silent Operation / No Cycling
- Operates on 12V DC or 24V DC
- Controls Pressure by Changing Motor Speed
- Speeds Up As Demand Increases
- Self-priming / Runs Dry
- No Accumulator Tank Needed
- CSA Listed / EN ISO 8846 Marine / C.E. Certified
- Protected under U.S. Patent #6,607,360
- Includes Inlet Strainer
|
|
|
SANISPLIT is an automatic soil and waste water pumping unit, which collects the water from the kitchen and bathroom and pumps it into the collection tanks, even without the necessary gradient. SANISPLIT includes a powerful and silent centrifugal pump controlled by a pressure switch, which starts the pump as soon as the water arrives in the unit's collection tank.
|
|
|
The RHEINSTROM Impellerpumpe IP 50 can be used for the promotion of drinking water or waste water. The parts coming with water into contact are made of stainless material. The pump is positioninsensitive. It is sucking in drying. A longer unlubricated operation should be avoided however, since otherwise the Impeller could suffer damage. The pump is available in 12 V and 24V execution.
|
|
|
The Rhine current diverter pump telex 370 is a large, expresses robust and chopper pump suitable for the permanent run. It is not sucking in and must be cultivated by from there either in the deepest place of the tank or be installed more deeply than the tank. A chopper is before-built for the actual pump part, which cuts the material to be conveyed up very finely. In case of maintenance the pump body can be divided very easily and with simple means. Contrary to the diverter pump F it is suitable for continuous operation. From there it Fäkalientanks up to a size of approx. 1 m ³ are ideal for this pump.
|
|
|
A spring and a deck wash pump, which are suitable also for the promotion of seawater. By its special construction this Rhine current pump is insensitive to the admixture of sand (grain size up to 6 mm), rust or other pollutants. The use of an unsolicited impeller and a most modern axial face seal make nearly completely maintenance-free this pump. The engine is appropriate for continuous operation. We suggest, with the installation, building into the sucking in line a foot or a sleeve setback valve. The pump needs to be filled by this measure only before first start-up with liquid. A refilling up when tearing the liquid column off is not necessary from there. Also air cushions in the line system do not impair the working reliability of the pump.
|
|
| ... products without information |
| |
|
|
see the results for the following category
