Plastic blocks

P. 150
block end of the bent tube to the side block assembly . Using the torque wrench and 11/16 attachment, tighten to 100 inch lbs (11.3 Newton Meters). if the regulator end of the bent tube was loosened, torque the jam nut to 40 inch lbs (4.5 Newton Meters). 11) Slide the PVC flange up towards

P. 151
in the side block shroud tube. Pull the corrugated tube over the PVC flange at the sideblock. Fasten the tie-wraps and trim the excess off the ends.

P. 126
110 © Copyright 1970-2010 Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 100408002 SuperLite® 27® Removing the port retainer. 8.5 Face Port 8.5.1 General The face port, or viewing lens, is made of a polycarbonate plastic. Small scratches on the exterior are not important

P. 36
20 © Copyright 1970-2010 Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 100408002 SuperLite® 27® The equalizing device. Nose block device Oral/nasal mask Helmet shell Knob, nose block Packing nut Port retainer O-ring When not needed, the knob is pulled out so the pad

P. 46
and lifting harness. Checking the one way valve. 3.6 Preparing the Helmet for Diving 3.6.1 Clean Face Port Thoroughly clean the face port with a soft cloth and a mild liquid soap solution. DO NOT USE ANY AEROSOL SPRAYS ON THE POLYCARBONATE PORT! 3.6.2 Check Moving Parts Check all moving parts

P. 146
over the PVC Flange and the regulator shroud rubber. 9) Install the second PVC flange in the other end of the corrugated tube. (1/4 of the flange should still show). 10) Attach the side block end of the bent tube to the side block assembly. Using the torque wrench and 11/16 attachment, tighten to "100

P. 35
Kirby Morgan® BandMasks® 18 & 28 © Copyright 1970-2010 Kirby Morgan Dive Systems, Inc. All rights reserved. Document #100720002 21 Earphone Microphone Oral/nasal mask Terminal block Binding post Waterproof Connector Plug Terminal Packing Gland Mask Frame O-ring Port Port Retainer

P. 88
-ring pick made of brass or plastic. Care must be taken not to scratch or damage the sealing surface on the hose fitting when removing the O-ring. If the fitting is gouged it will leak breathing gas. 7.4.5.4 Hose Assembly Replacement 1) Thread the hose assembly into the side block and tighten with

P. 87
block mounting stud hole, screw hole, or air flow hole. This could lead to drowning. WARNING WARNING ?CORROSIVE Avoid contacting the plastic components with acetone. Acetone can melt the components resulting in equipment failure. This could lead to drowning and possible death. 6) Slip

P. 128
Kirby Morgan® BandMasks® 18 & 28 114 © Copyright 1970-2010 Kirby Morgan Dive Systems, Inc. All rights reserved. Document #100720002 Take care not to lose the small o-ring on the back of the port retainer. 8.4 Face Port 8.4.1 General The face port, or viewing lens, is made of a polycarbonate

P. 74
Tube ID mm Max Rope Size mm Weight g A.257 Spinnaker pole cleat 14 - 38 - 6 18 A.357 Spinnaker pole ramp 14 - 38 - 6 18 A...94 SA..94 Part No. Description Seave Width mm Sheave Dia mm Tube ID mm Weight g A..94 Plastic mast head sheave box to fit mast ID 20mm 6 36 20 40 SA..94 Adaptor

P. 4
their resources to include their own design of injection moulding machines, metal press and punch machines and had increased their product range to include blocks, plastic cleats, sailmakers? hardware, stainless steel rigging gear and more. Today, you can look at most sailing dinghies and you?ll find products

P. 3
& hook racks 68 Highfield levers 65 Mast and boom straps 66 Mast gates and step 69 Mast tangs 69 Mirror dinghy mast fittings 67 Nylon mast & tube fittings 76 Plastic mast head sheave box 74 Rigging screws 71 Rigging stud screw 71 Sheave boxes 72 Sheave boxes - high tension 72 Sheave boxes -

P. 73
www.allenbrothers.co.uk 73 SPARS & RIGGING ACCESSORIES Sheave boxes - keelboat Specially designed for keelboat halyard entry and exit boxes with side flanges to reduce jamming. All sizes are suitable for ropes up to 10mm in diameter. A...8 A...8A A..28 Part No. Description Sheave Width mm

P. 7
A block is a single or multiple pulley. One or more sheaves are enclosed in an assembly between cheeks. In use a block is fixed to the end of a line, to a spar, or to a surface. Rope or line is threaded through the sheaves. Some blocks have a ratchet, which means that they turn freely

P. 19
à marine equipment GENOA CARS & TRACKS MODEL SAFE WORKING LOAD CALISMAYÙKÙ ' (kg) SHEAVE ROPE iP KALINLIGI 0 (max mm) TRACK RAY (mm) TRACK END RAY BASLlâl AG32P 1600 Polyacetal 20 32 Plastic AG32A 1900 Aluminum 20 32 Plastic AG40P 3000 Polyacetal 25 40 Plastic AG40A 3600 Aluminum 25 40 Plastic

P. 11
Length 3.40m Be m 1.20m SaiiArn 5.20m2 Hull weight 43kg Construction PoLypropyLene Mast Boom HAl ... I"'oat d Lum Coated aLum rew Blocks PH Skill Level Stainless Nylon 1288 Starter/Inter/Adv

P. 4
for achievements in plastics. The Topper is used in the Open University (elevision programme to illustrate the principies of craft, design and technology, the development of injection moulding techniques and the handling and use of plastics in industry.