|
|
|
Quick "slow burn" hydraulic magnetic circuit breakers offer protection when using direct currents. In over current situations they will trip, break the circuit and protect the equipment, they may be reset manually and are suitable up to 80 Vdc.
|
|
Single-pole, triple-throw switch permits four connection modes: Battery One, Battery Two, two batteries in parallel, or both off. Rated for 230 amps continuous, 345 amps momentary. For 6-volt to 32-volt systems. Includes alternator field circuit disconnect to prevent surges. Selector has positive click positions. Bakelite housing with copper washers, brass terminals, and brass nuts. Install with #10 screws.
|
|
|
Panel for 2 Battery Key Switch + 1 parallel Key Switch 200A (Max 1500A)
|
|
|
Copper contacts, stainless steel springs; polycarbonate body; fitted with automatic power interruption on the alternator if the battery isolator activates before turning off the engines. Specially suited for diesel motorizations, which due to large starting motors require heavy amperage; EC DIP 03299 certification made in accordance with law 94/95.
|
|
- For Use With 6, 12, 24 and 32 Volt Marine Electrical Systems
- Capacity: Rated 380 or 450 AMPS Continuous
850 or 1200 AMPS Intermittent (5 or 15 Seconds On, 5 Minutes Off)
|
|
Panel for 4 or 8 waterproof switches or push buttons
|
|
| ... products without information |
| |
FenderBud™ is designed for floating docks to secure your fenders properly instead of using ropes or tie wraps.
This FenderBud™ model is designed to protect the rear (stern) along with the swim platform while docking.
- Easily attaches to your dock for secure fender installation
- Designed to be placed in the rear of your slip to hold your fender securely
- Helps protect your platform and transom from dock collisions by holding the fender in proper position
- All aluminum construction for long life
- All stainless steel and nylon hardware included
- Installation is a snap requiring only simple hand tools
- Works with most popular 6" and 8" Fender designs
|
|
Edge Mount Kits
Design For Edge Applications
- Easily attaches to your dock for secure fender installation
- Designed to be placed on the Edge of your slip to hold your fender securely
- All aluminum construction for long life
- All stainless steel and nylon hardware included
- Installation is a snap requiring only common hand tools
- Works with most popular 8-1/2 " Fender designs
|
|
Use this Davis accessory to clip your fenders to rails, lifelines, side wing windows or cleats. Fender Tender II simplifies the handling and relocation of boat fenders. The "Railing Lock" firmly grasps rails from 7/8" to 1" (22 to 25 mm) diameter. New "Lifeline Lock" provides added safety. Use 1/4" to 3/8" (6 mm to 9 mm) diameter nylon line. Made of tough, sun-resistant plastic.
|
|
|
A real piece of gear - Superior quality throughout - made of heavy-gauge stainless steel. It's by far the sturdiest unit available-bar none! It's sleek, slim design provides 2" to 3" less protrusion into the deck area than other models and adjusts to any rake [right, left or vertical]. Collapses easily for off-season storage. Shipped complete with all hardware-no added mounting brackets to buy. Mounts easily on 7/8" or 1" diameter rail or may be deck mounted with holes provided.
|
|
|
Now available in two sizes. To suit two 200mm or two 240mm fenders. Stainless Steel - Marine Grade - 19mm diameter tube. Bright polished finish. Adjusts to various angles. Simply rivet or screw in position to bulkhead or rails.
|
|
FENDEQUIP FENDERCOVERS AVAILABLE TO FIT ANCHOR MARINE FENDERS
"The, must have, essential accessory for boats of all sizes including super yachts."
The surface of modern hard plastic fenders traps grit and dirt between the fender and topside.
The constant rubbing of bare fenders on the topsides will cause significant damage to the gel coat of your boat, which is normally very costly to repair.
Fendequip fender covers are specially designed to protect the topsides from fender scuff and reduce the need for expensive gel coat repairs. They are made from a premium stain resistant, non-abrasive, loop-knit acrylic fabric, which is both durable and fade resistant. They are available in a variety of colours and sizes to suit your individual requirements.
Fendequip fender covers will also protect your fenders from dirt and UV and will make your boat look clean and smart. Fendequip fender covers are the, must have, essential accessory for boats of all sizes including superyachts.
Colours: Standard colours throughout the Fendequip range are Navy Blue, Royal Blue, Black and Red. Or a special colour of your choice may be matched, when you place your order, at a minimal extra cost.
|
|
| ... products without information |
| |
... see all the products in the category
Fenders
|
|
|
see the results for the following category
