|
|
| This new feature makes accidental run-dry impeller damage a thing of the past |
|
| Flexible impeller boat pumps make excellent marine bilge pumps, principally because of their ability to handle bilge debris without damage. Because of the robust design many owners still use our 12 Volt dc or 24 Volt dc flexible impeller motor pump units that are up to 25 years old! Flexible Impeller Pumps also give the benefits of good flow, low cost, low size and weight, and are easily serviced and maintained. Most Flexible Impeller pumps must not be run dry, as this will damage the impeller which will require replacing. However, the Utility Puppy 2000 and 3000 both allow maximum of ten minutes dry running after initial prime. As with submersible pumps, flexible impeller pumps can be operated using a float or Hydro Air switch for boat, and remotely controlled from outside the bilge compartment. There is a wide range of flexible impeller pumps to choose from giving a range of flows, discharge heads, and self-priming options for a wide variety of applications such as ballast transfer, bait tank circulation, and deck wash duties |
|
FB-8 series Multipurpose Compact Heavy Duty Bronze Impeller Boat pumps
Compact design, raw water resistant pumps at an attractive price. With excellent self-priming capability, these pumps are ideal for applications like engine for boat cooling, bilge pumping, wash-down, refuelling, emergency and fire fighting.
Also ideally suited for shore for emptying septic boat tanks, flushing, cleaning and filling boat water tanks. |
|
Flow rate: 32 Litres/min (6.5 gallons/min)
Self-priming from dry up to 1.2m (4ft)
- Small bilge debris present no problem to these bronze bodied, flexible impeller boat pumps.
- Simple design means fewer wearing parts.
- ISO 8846 MARINE (Ignition protection).
- ISO 8849 MARINE (Bilge pump for boat standard). |
|
| The alternate marine pump is available in single speed or two speed with auto shift model; and we can also propose the rotating model, powered by an universal marine winch handle |
|
Engine for boats Cooling Boat pumps
Flexible impeller pumps are self-priming and therefore, are ideal for engine cooling, wash-down, circulation, and many general purpose on-board or dockside applications. The bronze bodies and stainless steel shafts are well situated for marine environments. They can operate in either rotational direction.
|
|
| The RHEINSTROM Impellerpumpe IP 50 can be used for the promotion of drinking water or waste water. The parts coming with water into contact are made of stainless material. The pump for boats is positioninsensitive. It is sucking in drying. A longer unlubricated operation should be avoided however, since otherwise the Impeller could suffer damage. The pump is available in 12 V and 24V execution. |
|
| ... products without information |
| |
HYDRAULIC HELMS
The hydraulic helms are of the axial pistons type. The helm housing is in aluminium with bronze gears and cylinder marine block for greater durability and longer life. The P20, P30 and P42 models are supplied with a built-in non return and relief valve. For all the other models a non return valve shall be mounted separately. The hydraulic helms are supplied without any fitting. Complete kit of fittings are available separately, which shall be specified when placing the order. The codes and descriptions of the different marine kits can be found on the price list. |
|
| The hydraulic helms are of the axial pistons type. The helm housing is in aluminium with bronze gears and cylinder block for boat for greater durability and longer life. The P20, P30 and P42 models are supplied with a built-in non return and relief valve. For all the other models a non return valve shall be mounted separately. The hydraulic helms are supplied without any fitting. Complete kit of fittings are available separately, which shall be specified when placing the order. The codes and descriptions of the different marine kits can be found on the price list. |
|
Reliable operation of a steering system depends upon the quality and performance of the helm pump. The Jastram "H" series manually operated helm is a precision made axial piston pump specifically designed to operate effectively at a very slow turning rate.
The H60, 90 and 110 are among the largest helm boat pumps made and provide excellent primary or backup steering for large steering systems for boats. |
|
Reliable operation of a steering system depends upon the quality and performance of the helm pump for boat. The Jastram "H" series manually operated helm is a precision made axial piston pump specifically designed to operate effectively at a very slow turning rate.
The H26/36/58 provide excellent primary or backup steering for small and relatively large marine steering systems. |
|
| ... products without information |
| |
| ... products without information |
| |
| ... products without information |
| |
| ... products without information |
| |
|
|
see the results for the following category
