|
|
Armstrong Positive Floatation Outboard Brackets are among the finest outboard mounting systems in the industry … setting the standard for outboard propulsion worldwide. Armstrong Brackets move the outboards aft and raise the engine running position, allowing the prop to get a better “bite”. This results in reduced time to plane, increased top speed, and better fuel economy.
Additional Features…
• Transom angle match
• Custom colors
• Choice of platform width
• Built in ladder mounts
• Underwater Lights
• Kicker engine bracket on platform
• Bracket built to transom shape
• Flotation chambers sized for extra buoyancy
• Bracket bottom matched to hull deadrise
• Engine centers to fit your particular engines, hull design, and intended use
|
|
Breakdown protected anti-vibration engine mounts !
Our anti-vibration engine mounts are designed especially for propulsion engines and generators on board of ships. Amartech anti-vibration engine mounts combine a small installation height with a relatively high deflection, thus much isolation. The movements of the flexible mounted engines / generators are limited in 3 directions.
|
|
|
Fissaggio su piano con spalle in acciaio inox lucidato e tavola in compensato marino di mogano. Appositamente realizzato per imbarcazioni con plancetta di poppa dell'ultima generazione, integrata nella fabbricazione della barca. Si fissa sul lato superiore della plancetta.
|
|
Soundown Engine Isolation Mounts are used for the reduction of structureborne noise from propulsion engines. We provide mountings of all types, for installations up to 6000 hp. Soundown Flexible Engine Mounts are high performance adjustable isolators for both thrust taking and non-thrust applications. This range of mounts is available in various configurations, all with heavy-duty features, including some types available in steel, cast iron, or aluminum constructions. Our mounts are available with or without height adjustment, and are specified for each unique application to deliver the best isolation performance possible.
|
|
Poly Flex engine mounts are specifically designed to provide vibration isolation for your machinery while also providing high resistance to movement caused by dynamic loads, such as propeller thrust and lateral loads experienced in marine applications.
|
|
Normally, motor mounts are designed to accept static, vertical loads with various hardness of rubber to attain the desired critical dampening ratio and static deflection. With all the power of propeller thrust pushing on the engine and motor mounts, the rubber part of the motor mount, by itself, has to be hard to withstand these horizontal, shear forces while maintaining the critical alignment between the engine and shaft.
In many instances, there are more pounds of propeller thrust to contend with than the static, vertical pounds of engine and gear weight. Under this condition, the very hard motor mounts afford little isolation of the engine vibration to the hull.
To isolate the engine vibration to the hull with truly soft mounts, either expensive thrust bearing assemblies must be used, or -- Evolution Motor Mount Compensators (EMMC). The EMMC will handle all the forward and reverse thrust on the engine and allow for softness in mounts that have eliminated up to 80 percent of the engine vibration to the hull. This alone has reduced sound levels on board a vessel by as much as 15 decibels. Soft mounts coupled to the EMMC positively change the environment aboard any vessel immediately on starting the engine(s).
With a "free floating" engine on soft mounts, it is recommended that all connections to the engine be flexible, i.e., flexible shaft coupling, exhaust coupling, etc. We would be happy to quote on flexible shaft couplings.
|
|
The Metalastik "Cushyfloat" Motor Mount is an ideal unit for isolating up to 80 percent of marine engine vibrations to the hull. This compact, low-profile-designed motor mount is easily installed and adjusted under engines.
Each component of the "Cushyfloat" mount is of highest quality:
Premium grade natural rubber isolator
Zinc-plated outer covers
Large steel studs
Oversized steel hexagonal adjustment nut
Strong steel base
This combination provides the correct deflections, high load capacity, and a long service life.
Our technical assistance serves to provide each and every installation with the duronmeter rating(s) to attain the desired critical damping ratios and static deflections.
Metalastik Vibration Control Systems are a leading brand of marine motor mounts sold throughout North America and Europe. OEMs of the highest quality yachts rely on "Cushyfloat" motor mounts for the optimum isolation of engine vibrations to the hull.
|
|
|
We sell our products to professionals only...if you are an individual, please don't send any requests. Thank you very much.
|
|
|
FRANCE HELICES MANUFACTURES ALL TYPES OF BRACKETS. BECAUSE OF THE LARGE NUMBER OF ANGLES, FRANCE HELICES HAS DEVELOPED A WIDE RANGE OF PATTERNS WITH AN EXCLUSIVE MODIFICATION ANGLE SYSTEM IN ORDER TO ALLOW ANY ANGLE OF INCLINATION BEFORE CASTING. THE DESIGN HAS BEEN MADE TAKING IN CONSIDERATION THE FOLLOWING PARAMETERS : MINIMUM DRAG, MINIMUM WEIGHT, STANDARD N.A.C.A. PROFILE, AIR INDUCTING (OPTION), NON CAVITATING PROFILE, HUB SIZED ACCORDING TO PROPELLER HUBS TO AVOID HYDRODYNAMIC DISTURBANCES.
|
|
The Poly Flex 'B-series' machinery mounts are manufactured from engineering grade polymers that are resistant to most fuels, oils and chemicals. (contact Poly Flex for chemical resistance table)
This model of mount is ideal for simple support or support/levelling of machinery.
The table below shows a sample of the smaller mounts in the range.
The largest in the range has a diameter (A)=140mm with a working load of 2000kg
|
|
| ... products without information |
| |
Edge Mount Kits
Design For Edge Applications
- Easily attaches to your dock for secure fender installation
- Designed to be placed on the Edge of your slip to hold your fender securely
- All aluminum construction for long life
- All stainless steel and nylon hardware included
- Installation is a snap requiring only common hand tools
- Works with most popular 8-1/2 " Fender designs
|
|
FenderBud™ is designed for floating docks to secure your fenders properly instead of using ropes or tie wraps.
This FenderBud™ model is designed to protect the rear (stern) along with the swim platform while docking.
- Easily attaches to your dock for secure fender installation
- Designed to be placed in the rear of your slip to hold your fender securely
- Helps protect your platform and transom from dock collisions by holding the fender in proper position
- All aluminum construction for long life
- All stainless steel and nylon hardware included
- Installation is a snap requiring only simple hand tools
- Works with most popular 6" and 8" Fender designs
|
|
Use this Davis accessory to clip your fenders to rails, lifelines, side wing windows or cleats. Fender Tender II simplifies the handling and relocation of boat fenders. The "Railing Lock" firmly grasps rails from 7/8" to 1" (22 to 25 mm) diameter. New "Lifeline Lock" provides added safety. Use 1/4" to 3/8" (6 mm to 9 mm) diameter nylon line. Made of tough, sun-resistant plastic.
|
|
|
A real piece of gear - Superior quality throughout - made of heavy-gauge stainless steel. It's by far the sturdiest unit available-bar none! It's sleek, slim design provides 2" to 3" less protrusion into the deck area than other models and adjusts to any rake [right, left or vertical]. Collapses easily for off-season storage. Shipped complete with all hardware-no added mounting brackets to buy. Mounts easily on 7/8" or 1" diameter rail or may be deck mounted with holes provided.
|
|
|
Now available in two sizes. To suit two 200mm or two 240mm fenders. Stainless Steel - Marine Grade - 19mm diameter tube. Bright polished finish. Adjusts to various angles. Simply rivet or screw in position to bulkhead or rails.
|
|
FENDEQUIP FENDERCOVERS AVAILABLE TO FIT ANCHOR MARINE FENDERS
"The, must have, essential accessory for boats of all sizes including super yachts."
The surface of modern hard plastic fenders traps grit and dirt between the fender and topside.
The constant rubbing of bare fenders on the topsides will cause significant damage to the gel coat of your boat, which is normally very costly to repair.
Fendequip fender covers are specially designed to protect the topsides from fender scuff and reduce the need for expensive gel coat repairs. They are made from a premium stain resistant, non-abrasive, loop-knit acrylic fabric, which is both durable and fade resistant. They are available in a variety of colours and sizes to suit your individual requirements.
Fendequip fender covers will also protect your fenders from dirt and UV and will make your boat look clean and smart. Fendequip fender covers are the, must have, essential accessory for boats of all sizes including superyachts.
Colours: Standard colours throughout the Fendequip range are Navy Blue, Royal Blue, Black and Red. Or a special colour of your choice may be matched, when you place your order, at a minimal extra cost.
|
|
| ... products without information |
| |
... see all the products in the category
Fenders
|
Fast lifebuoy release system.
Holds standard ring or horseshoe lifebuoy, up to a circumference of 400 mm, firmly in place.
Ensures lifebuoy is quick and easy to launch.
Made of solid, flexible and durable polyurethane.
Fits most guard rails.
|
|
This stamped aluminum holder is powder coated to withstand the harsh marine environment. It mounts to any 7/8" or 1" railing. Complete with a nylon strap to hold your buoy secure.
|
|
|
COMMERCIAL QUALITY - Features heavy-duty, welded stainless steel construction throughout for a lifetime of maintenance-free use. Its rugged beauty will enhance any installation. Available in three standard sizes with pre-drilled holes for stanchion and life line mounting (see sketch), as well as cabin wall installations.
|
|
| ... products without information |
| |
|
... see all the products in the category
Lifebuoys
|
|
|
see the results for the following category
