|
|
|
|
|
|
|
Installed and ready to use in 30 minutes!
Gobius is the first level indicator in the world that measures from the outside. Installing Gobius to your tank is very easy. Instead of the traditional way of installation, i.e taking the tank apart and drilling holes, you simply attach the sensors to the tank on the outside.
All Gobius products measure from the outside
Very easy to install and setup
Suitable for all tank materials; stainless steel/steel, aluminum, plastic and fibre glass
Gobius can be retro-fitted to any shape or size of a tank
Analouge output for gauges from Wema, VDO, Faria, Teleflex, Phillipi…
Supports NMEA 2000
Extremely low electricity consumption, less than 40 mA (12 Volts)
Support 12 – 24 Volts
30 minutes to install
On the sensor there is a disc of tape that is provided to attach the sensor directly onto the surface of your tank. The panel may be placed in the washroom. All necessary cables and plugs needed to connect the sensors and the panel with the control unit are included.
Very easy to calibrate
No tanks look the same. There are always differences in e.g. size, construction, thickness and age. In order to compensate for these differences you have to calibrate the tank before you start to use your Gobius. However, the calibration only takes a few seconds.
The Gobius technology (patented)
Each sensor that is placed onto the tank wall consists of a shaker and an accelerator. When the shaker creates a vibration in the tank wall, the accelerator measures the size of the vibration and passes the data on to the control unit.
Art No 970497
|
|
Continuously monitors 3 levels of holding and water tanks and monitors battery level. Includes rocker switch for pump if needed. Suitable for tanks up to 26" tall. Optional grey water tank sensor available.
- Easy to Install
The Smart Sense System is attached to the outside of the tank as shown.
- Reliable
No micro float switches or probes to degrade and fail. Electronic sensors are outside the tank
- Attractive and User Friendly
Smart Sense System includes a display panel with LED lights and hidden mounting screws inside snap out mounting bezel.
|
|
Codice prodotto: HPYXXXXX/HPWXXXXX
Our liquid level senders are level indicating devices compatible with all the petrol and water level gauges available on the market.
They are fuel, sea-water and acid resistant because they are made of the highest stainless steel AISI 316. They are perfectly watertight and have a flange with holes that allows a perfect fitting on the tank.
The sender cables must be connected to the measuring terminals of the indicating instruments, as explained in the user's manuals of the later.
The level indicating gauges available on the market can be divided into two main categories:
1) standard gauges (STD)
2) inverted gauges (VDO-type)
|
|
|
You can now monitor and control up to 8 tanks of any shape or construction. You can see how much is in each tank, pump out each tank, automatically start a watermaker when water levels are low, and automatically turn off watermakers whaen tanks are full. You can be alarmed when fuel is low, deactivate toilets when black tanks are full. The very Smart TC-8000 Controller provides an intelligent networked solution for the monitoring and control of up to eight tanks. The system consists of the TC-8000 display controller (as seen above) up to eight HT-100 or HT-100/P tank controllers to control each tank, and any number of optional RD-800 repeater displays communicating via a 2-wire network cable with a maximum cable length of 1000 meters. This means you can have the main display at the helm and another display in the bedroom or second helm station. Control the fuel, water, grey and black tanks so you never run out of water or fuel again.
|
|
|
|
|
|
|
CAPACITIVE SENDER
Codice prodotto: HPCHDS/ HPCHDV / HPCHG /
INTERNATIONAL PATENT.
Our new capacitive level sender offers precision of measurement, reliability and quality that are
always sought after and appreciated by the end-users. They were designed to meet the demand
for a precise, durable, universal and user-friendly sending unit. The following characteristics
reflect its major features and advantages:
- Capacitive level sender is compatible with the majority of the measuring gauges present in the market (Osculati, Aqua Meter, Vetus, Gaffrig, VDO, Faria) and can be programmed to work with any other non-standard gauge.
- It has only two connecting cables as if it were a regular resistive sender. This feature makes its installation extremely easy because no additional cables have to be provided.
- Our patented electronic system allows the sender to feed autonomously.
- It can be connected to the gauge in place of any existing sender without any special adjustments. Thus the are no costs associated with switching to this type of sender from any other current model.
Capacitive level senders can be used for FUEL, WATER AND WASTEWATER. The sender of each
category in its turn can be either generic or dedicated.
|
|
Features:
- Tank level monitoring for up to 3 tanks
- 14 selectable legends for tank descriptions eg. Fuel, Water, Blackwater
- Hi - Low tank level alarms for 3 tanks
- Tank levels displayed in graphic or percentage format
- Units displayed in litres, imperial gallons or US gallons
- Audible alarm with mute function
- Power supply 10-35VDC
- Display is backlit for easy night time viewing
The 600-TLMN tank level monitor will interface directly with a precalibrated BEP Ultasonic Tank Sender. (Part No. TS1) If fitting an uncalibrated TS1, the sender can be calibrated via the 600-TLMN monitor.
|
|
Product Details:
The 600-TG offers economical monitoring for fresh or grey water tanks (plastic or fibreglass only). Using 600-TGSK strategically mounted well nuts will give 4 tank levels. Supplied with one sender kit. Second sender ordered separately.
Also available is the RV-TS Tank sender. Only one hole is required for installation, the sender is sealed via external lock nuts. Only suits tanks with maximum depth of 280mm.
|
|
The 600-SOM offers the following features:
- Programmable legends for functions being monitored eg, forward bilge pump, aft bilge pump, engine room lights, salt water pump, locker lights, etc.
- Selectable alarm functions with mute capability, eg.
1. Short beep for indicating an engine room light has been switched on, recurring every 30 minutes if light is left on
2. Continuing alarm for pump operation which can be muted by alarm mute switch
- Visual indication as well as audible alarm on screen to indicate function in operation. If more than one function is alarming this will alternate on flashing screen.
- Provision for external alarm
- Power supply 10-35VDC
- Display is backlit for easy night time viewing
|
|
|
|
|
|
|
Our tank sensor is driven by the air pressure generated by the water level. It must be installed in the upper part of the tank with the rubber hose that enters the tank so that, when the level of the water increases reaching the rubber hose, the pressure switch effects the contact. The pressure switch, located outside the tank, is a normal on-off switch that, being electrically connected with the control panel of our WCs (grey/black cable), warns through a red led that the tank is nearly full (usually the led is green).
The sensor may be used to commutate different alarms.
It is activated when, further to the water thrust, air pressure generates within the rubber hose. The switch commutates to ON when the water will have submerged the rubber hose for nearly five centimeters.
The sensor is really reliable since there is no mechanical movement in the tank but only the air pressure (there is also a retardant that prevents contact in case of movement of the water while at sea, since the air pressure must remain for over 3 seconds at a given level).
|
|
| ... products without information |
| |
Codice prodotto: HPYXXXXX/HPWXXXXX
Our liquid level senders are level indicating devices compatible with all the petrol and water level gauges available on the market.
They are fuel, sea-water and acid resistant because they are made of the highest stainless steel AISI 316. They are perfectly watertight and have a flange with holes that allows a perfect fitting on the tank.
The sender cables must be connected to the measuring terminals of the indicating instruments, as explained in the user's manuals of the later.
The level indicating gauges available on the market can be divided into two main categories:
1) standard gauges (STD)
2) inverted gauges (VDO-type)
|
|
|
You can now monitor and control up to 8 tanks of any shape or construction. You can see how much is in each tank, pump out each tank, automatically start a watermaker when water levels are low, and automatically turn off watermakers whaen tanks are full. You can be alarmed when fuel is low, deactivate toilets when black tanks are full. The very Smart TC-8000 Controller provides an intelligent networked solution for the monitoring and control of up to eight tanks. The system consists of the TC-8000 display controller (as seen above) up to eight HT-100 or HT-100/P tank controllers to control each tank, and any number of optional RD-800 repeater displays communicating via a 2-wire network cable with a maximum cable length of 1000 meters. This means you can have the main display at the helm and another display in the bedroom or second helm station. Control the fuel, water, grey and black tanks so you never run out of water or fuel again.
|
|
|
|
|
|
|
CAPACITIVE SENDER
Codice prodotto: HPCHDS/ HPCHDV / HPCHG /
INTERNATIONAL PATENT.
Our new capacitive level sender offers precision of measurement, reliability and quality that are
always sought after and appreciated by the end-users. They were designed to meet the demand
for a precise, durable, universal and user-friendly sending unit. The following characteristics
reflect its major features and advantages:
- Capacitive level sender is compatible with the majority of the measuring gauges present in the market (Osculati, Aqua Meter, Vetus, Gaffrig, VDO, Faria) and can be programmed to work with any other non-standard gauge.
- It has only two connecting cables as if it were a regular resistive sender. This feature makes its installation extremely easy because no additional cables have to be provided.
- Our patented electronic system allows the sender to feed autonomously.
- It can be connected to the gauge in place of any existing sender without any special adjustments. Thus the are no costs associated with switching to this type of sender from any other current model.
Capacitive level senders can be used for FUEL, WATER AND WASTEWATER. The sender of each
category in its turn can be either generic or dedicated.
|
|
Product Details:
The 600-TG offers economical monitoring for fresh or grey water tanks (plastic or fibreglass only). Using 600-TGSK strategically mounted well nuts will give 4 tank levels. Supplied with one sender kit. Second sender ordered separately.
Also available is the RV-TS Tank sender. Only one hole is required for installation, the sender is sealed via external lock nuts. Only suits tanks with maximum depth of 280mm.
|
|
|
|
|
|
|
Our tank sensor is driven by the air pressure generated by the water level. It must be installed in the upper part of the tank with the rubber hose that enters the tank so that, when the level of the water increases reaching the rubber hose, the pressure switch effects the contact. The pressure switch, located outside the tank, is a normal on-off switch that, being electrically connected with the control panel of our WCs (grey/black cable), warns through a red led that the tank is nearly full (usually the led is green).
The sensor may be used to commutate different alarms.
It is activated when, further to the water thrust, air pressure generates within the rubber hose. The switch commutates to ON when the water will have submerged the rubber hose for nearly five centimeters.
The sensor is really reliable since there is no mechanical movement in the tank but only the air pressure (there is also a retardant that prevents contact in case of movement of the water while at sea, since the air pressure must remain for over 3 seconds at a given level).
|
|
|
|
|
|
|
Installed and ready to use in 30 minutes!
Gobius is the first level indicator in the world that measures from the outside. Installing Gobius to your tank is very easy. Instead of the traditional way of installation, i.e taking the tank apart and drilling holes, you simply attach the sensors to the tank on the outside.
All Gobius products measure from the outside
Very easy to install and setup
Suitable for all tank materials; stainless steel/steel, aluminum, plastic and fibre glass
Gobius can be retro-fitted to any shape or size of a tank
Analouge output for gauges from Wema, VDO, Faria, Teleflex, Phillipi…
Supports NMEA 2000
Extremely low electricity consumption, less than 40 mA (12 Volts)
Support 12 – 24 Volts
30 minutes to install
On the sensor there is a disc of tape that is provided to attach the sensor directly onto the surface of your tank. The panel may be placed in the washroom. All necessary cables and plugs needed to connect the sensors and the panel with the control unit are included.
Very easy to calibrate
No tanks look the same. There are always differences in e.g. size, construction, thickness and age. In order to compensate for these differences you have to calibrate the tank before you start to use your Gobius. However, the calibration only takes a few seconds.
The Gobius technology (patented)
Each sensor that is placed onto the tank wall consists of a shaker and an accelerator. When the shaker creates a vibration in the tank wall, the accelerator measures the size of the vibration and passes the data on to the control unit.
Art No 970497
|
|
Continuously monitors 3 levels of holding and water tanks and monitors battery level. Includes rocker switch for pump if needed. Suitable for tanks up to 26" tall. Optional grey water tank sensor available.
- Easy to Install
The Smart Sense System is attached to the outside of the tank as shown.
- Reliable
No micro float switches or probes to degrade and fail. Electronic sensors are outside the tank
- Attractive and User Friendly
Smart Sense System includes a display panel with LED lights and hidden mounting screws inside snap out mounting bezel.
|
|
|
|
see the results for the following category : 
