|
|
|
Ecosea have developped Metprotect™, a water and oxygen proof coating. Metprotect™ is a high performance, easy to use range of unique, single component, surface tolerant anticorrosive primers. Suitable for use above and below the waterline, the Metprotect™ range is ideal for steel, iron and many other metals. I can be applied by Ecosea Approved Installers or by surface preparation contractors.
|
|
Extra waterproof protection for the gel coat.
Gel-Gard™ provides high performance protection against osmosis for GRP. It is a professionally applied, high build, 100% solids, solvent free epoxy resin.
|
|
|
Seajet 118 Ultra-build epoxy primer provides a high build, abrasion resistant anticorrosive barrier coat for all surfaces. Its also tolerant to a surface which cannot be prepared to the highest standard.
|
|
SEAJET 011 is an anticorrosive primer and binder coat for use under SEAJET antifoulings
Advantages include:
- Quick drying
- Good adhesion to subsequent coats even after prolonged weathering.
- Allows extended overcoating intervals before the application of antifoulings
- Good sea-water resistance.
|
|
CREATES AN ACTIVE ANODIC ZINC LAYER THAT PROVIDES CATHODIC PROTECTION TO EXPOSED METAL BELOW THE WATERLINE.
CREATES A PASSIVE ZINC COATING THAT RESISTS CORROSION ABOVE AND BELOW THE WATERLINE.
ZINGARD is a one component cold applied zinc coating which contains a minimum of 96% pure zinc when dry, providing cost effective and reliable long lasting corrosion protection to all ferrous metals. Its dry layer contains a pure zinc content of more than 96%, as well as synthetic resins which allow the electrochemical bonding of the zinc to the metal. ZINGARD is non-toxic and free from xylene, toluene, Methyl-Ethyl-Keton (M.E.K.) and methylene chloride.
|
|
|
PO: One-pot polyurethane watertight primer formulated with DESMODUR® E resin to prevent osmosis on polyester. Easy to use and very watertight. P.O hardens by reacting with moisture in the air .
|
|
|
Nautix PE is a 2 pot high quality epoxy primer to protect polyester, steel and aluminium and to improve paints adhesion. Nautix PE is highly durable and resistant to abrasion.
|
|
HPE: high built epoxy primer for polyester, steel and aluminium
· High durability and resistance to abrasion
· Application by brush, roller
· At 15° C : overcoating without sanding between 5 and 10h
· Dull at paper grade 150-180 imperatively after 20 hours
· End dry after 72 hours
· 8 m2/litres per coat
· Diluant : DP
· 0.75 litre - 2.5 litres - 20 litres
|
|
P1: Primer for paint adhesion
and protection anti corrosion
· Nautix P1 is a conventional adhesion primer . P1 can also be used as a protective primer for wood and anticorrosion coating for steel.
· Apply 1 coat to improve the adhesion of paint on GRP surface and 3 to 4 coats for protection
· Application by brush, roller, spray gun
· 13m2/Ltr per coat
· At 15 C : overcoating after 3 hours
· At 15 C : dry after 6 hours
· Packing: 0,75 L - 2,5 L - 20 L
|
|
|
Etch Primer is a pre-treatment primer for use on aluminium, galvanized steel, zinc-sprayed surfaces and lead. It provides an excellent key prior to the application of primers
|
|
|
ALEXSEAL® Protective Primers provide corrosion-prevention for aluminum or steel. They are easy to apply using either a sprayer or roller. Superior adhesion properties work equally well above and below the waterline and establish a sealed substrate that is ready to be faired to perfection.
|
|
|
For use on glassfibre, wood, steel and aluminium, a two pack high performance epoxy priming and undercoating system. This product has outstanding corrosion, impact and water resistance qualities both above and below the waterline. Can be used for osmosis protection when application takes place at low temperatures. An excellent protective coating between the substrate and Poly Best topcoat, ensuring longevity of the system.
|
|
A quick drying, high performance, two-component epoxy for application to sound gelcoats to help protect against osmosis.
Gelshield® is provided in two shades (green and grey) to ensure complete coverage.
Suitable for use in temperatures down to 5°C.
Coverage: 6m2/750ml 20.3m2/2.5lt
|
|
Prep G is a "black out" primer to be used on glass, polycarbon (PC) and acrylic glass (PMMA) without ceramic coating (frit) before dispensing the glazing 70-08A, 70-11, and 70-12 adhesives.
Prep G provides ultraviolet light protection to the bond line. Note: UV protection is required for all direct glazing (windshield and windscreen) bonding applications. Factory applied frits provide UV protection.
Prep G must be used on glass that does NOT have ceramic coating (frit) and must be APPLIED BEFORE the glazing adhesive. Read and follow instructions in the Technical Data Sheet.
|
|
Two-part polyurethane primer for the protection of particularly demanding surfaces. Ideal base for a long-lasting project when combined with Polygloss, Tropikal 380/480/580, Antiskid and Monotreten projects. Excellent filling properties.
Use Uni Primer on:
Topsides / bilges of wooden, plywood, polyester or metal boats (ships, rowboats, pleasure boats, fishing boats) (no anti-rust protection).
|
|
Awlgrip 545 Epoxy Primer-Base mixed 1:1 by volume with D3001.
Spray reduced 15-25% with T0006.
Brush reduced 0-20% with T0031. 2-3 mils (50-75 microns) dry film thickness/2 coats.
|
|
|
ALEXSEAL® Finishing Primers provide an optimum base for the final topcoat, thanks to an advanced epoxy formula that features fast buildup during application with excellent adhesion to a variety of substrates and a non-porous surface that sands extremely well.
|
|
|
ALEXSEAL® High Build Surfacers are high build sprayable epoxy coatings that use pigments and extenders which offer various surface building qualities and provide ideal sanding characteristics to achieve a yacht finish.
|
|
Interprotect® is a quick drying, easy to apply two-pack epoxy primer for high performance protection on all rigid substrates.
It's two-component application gives excellent anti-corrosive and abrasion resistance properties and it can be used equally above or below the waterline.
Coverage: 6m2/750ml 20.3m2/2.5lt
|
|
Prep M is a "wash primer" that improves bond strength of SMP-based products on most non-porous substrates.
Use Prep M on non-porous substrates. In cases where high thermal or physical loads-especially under humid conditions requiring ultimate adhesion-use Prep M.
A clean, dry and grease free substrate is necessary for ultimate adhesion. Read and follow instructions in Technical Data Sheet and Material Safety Data Sheets.
Pretreatment of plain aluminum, steel, copper and brass surfaces
Pretreatment of powder coated metals.
Pretreatment of lacquered metals (conduct a pre-test)
Pretreatment of polyester (FRP)
Pretreatment of ABS
Pretreatment of PVC
|
|
Quick drying, high opacity primer and undercoat providing excellent durability and surface stability in preparation for overcoating with single pack systems. Suitable as an above water primer for all substrates (especially steel) and as an undercoat for Brilliant Enamel.
|
|
|
International Yacht Primer is a general purpose metallic grey primer for use on wood, steel and alloy above the water line only.
|
|
Prime before using Topside Paint on:
- Bare wood & fiberglass surfaces
Rust-Oleum Marine Coatings Primer for Wood & Fiberglass (for use above the waterline only)
- Bare metal surfaces
Rust-Oleum Marine Coatings Primer for Metal (for use above the waterline only)
- Previously painted surfaces
Either of the Rust-Oleum Marine Coatings Primers can be used if desired. Priming is not necessary unless paint is cracked, peeling, or otherwise unsound.
|
|
Undercoat for excellent long-lasting anti-rust protection. Excellent durability in constant contact with water contrary to linseed oil primers. Greater elasticity than standard anti-rust products. Receives most surface painting systems. Excellent workability. Ensures a smooth surface. Satisfactory adhesion to old coatings. Marine Primer is a special resins-based primer with a specific weight of 2.45 kg/lt. Apply directly on rust (remove only thick flakes). It is important to stir thoroughly before application. For the maintenance of wooden surfaces, it is recommended to add the special resins solution to the primer. MARINE PRIMER is ideal if long-lasting exposure to UV radiation is required without application of a final coat. A multiple-use product, since MARINE PRIMER is the primer for wood and metal surfaces painted with Paintol, Metal-x, Polygloss, Tropikal 380/480/580, Monotreten and Antiskid products.
Ideal for the maintenance of iron surfaces, inside and outside the sea.
Suitable for the maintenance of wooden boats.
Excellent undercoat for Tropical products.
|
|
|
One-part, non-flammable, resin-based primer for use on oily woods. Developed by BoatLIFE (The Polysulfide Experts) to promote maximum adhesion with all polysulfide sealants.
|
|
Fund of monocomposant fixing.
It supports the adhesion of the antifouling and the paints monocomposant on a new gelcoat.
To degrease with the SIRIO, then after having sandpapered with a paper with l%u2019eau fine grain, to let dry the support and to apply a layer of ANCHORPRIMER (max. thickness of the film dryness 15% u03BC).
|
|
|
PRIMER especially worked out to obtain an excellent adherence on the bronze propellers, the trees and alloys as well as the base plates. Its association with the ORION Antifouling makes it possible to reduce the stains considerably.
|
|
| ... products without information |
| |
... see all the products in the category
Primers
|
|
|
