|
|
|
Flexible impeller pumps make excellent bilge pumps, principally because of their ability to handle bilge debris without damage. Because of the robust design many owners still use our 12 Volt dc or 24 Volt dc flexible impeller motor pump units that are up to 25 years old! Flexible Impeller Pumps also give the benefits of good flow, low cost, low size and weight, and are easily serviced and maintained. Most Flexible Impeller pumps must not be run dry, as this will damage the impeller which will require replacing. However, the Utility Puppy 2000 and 3000 both allow maximum of ten minutes dry running after initial prime. As with submersible pumps, flexible impeller pumps can be operated using a float or Hydro Air switch, and remotely controlled from outside the bilge compartment. There is a wide range of flexible impeller pumps to choose from giving a range of flows, discharge heads, and self-priming options for a wide variety of applications such as ballast transfer, bait tank circulation, and deck wash duties
|
|
Ideal for portable use on Outboards, Stern Drives, or 4 Stroke PWC's or can be Permanently Installed
4' Dipstick & Drain Tubing
8' Power Cords with Alligator Clips
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps oil, diesel or water
Built in fuse for motor protection
|
|
Ideal for Two Engine Service - Either Two Engine, Engine / Generator or Diesel Engine / Transmission combination on Inboard sailboat or power boat applications
Two way shut off Brass valve with adapters for 1/2" ID hose installation
Mounting plate for easy engine room installation
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps water, oil and diesel fuel
Built in fuse for motor protection
|
|
Ideal for single inboard/outboard sailboat or powerboat application
Single shut off Brass valve with adapters for 1/2" ID hose installation
Mounting plate for easy engine room installation
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps water, oil and diesel fuel
Built in fuse for motor protection
|
|
Ideal for portable use or can be permanently installed
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps oil, diesel or water
Built in fuse for motor protection
|
|
Flow rate: 32 Litres/min (6.5 gallons/min)
Self-priming from dry up to 1.2m (4ft)
- Small bilge debris present no problem to these bronze bodied, flexible impeller pumps.
- Simple design means fewer wearing parts.
- ISO 8846 MARINE (Ignition protection).
- ISO 8849 MARINE (Bilge pump standard).
|
|
- Constructed from marine quality bronze and stainless steel for ruggedness and reliability.
- Easy to service and maintain.
- Inexpensive to buy and operate.
- Will tolerate abrasive wear (this may affect performance - seek advice from your distributer).
- Handles hard and soft solids without clogging.
- Can pump in either direction.
- Will not airlock.
|
|
|
The RHEINSTROM Impellerpumpe IP 50 can be used for the promotion of drinking water or waste water. The parts coming with water into contact are made of stainless material. The pump is positioninsensitive. It is sucking in drying. A longer unlubricated operation should be avoided however, since otherwise the Impeller could suffer damage. The pump is available in 12 V and 24V execution.
|
|
| ... products without information |
| |
|
Flexible impeller pumps make excellent bilge pumps, principally because of their ability to handle bilge debris without damage. Because of the robust design many owners still use our 12 Volt dc or 24 Volt dc flexible impeller motor pump units that are up to 25 years old! Flexible Impeller Pumps also give the benefits of good flow, low cost, low size and weight, and are easily serviced and maintained. Most Flexible Impeller pumps must not be run dry, as this will damage the impeller which will require replacing. However, the Utility Puppy 2000 and 3000 both allow maximum of ten minutes dry running after initial prime. As with submersible pumps, flexible impeller pumps can be operated using a float or Hydro Air switch, and remotely controlled from outside the bilge compartment. There is a wide range of flexible impeller pumps to choose from giving a range of flows, discharge heads, and self-priming options for a wide variety of applications such as ballast transfer, bait tank circulation, and deck wash duties
|
|
Ideal for portable use on Outboards, Stern Drives, or 4 Stroke PWC's or can be Permanently Installed
4' Dipstick & Drain Tubing
8' Power Cords with Alligator Clips
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps oil, diesel or water
Built in fuse for motor protection
|
|
Ideal for Two Engine Service - Either Two Engine, Engine / Generator or Diesel Engine / Transmission combination on Inboard sailboat or power boat applications
Two way shut off Brass valve with adapters for 1/2" ID hose installation
Mounting plate for easy engine room installation
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps water, oil and diesel fuel
Built in fuse for motor protection
|
|
Ideal for single inboard/outboard sailboat or powerboat application
Single shut off Brass valve with adapters for 1/2" ID hose installation
Mounting plate for easy engine room installation
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps water, oil and diesel fuel
Built in fuse for motor protection
|
|
Ideal for portable use or can be permanently installed
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps oil, diesel or water
Built in fuse for motor protection
|
|
Flow rate: 32 Litres/min (6.5 gallons/min)
Self-priming from dry up to 1.2m (4ft)
- Small bilge debris present no problem to these bronze bodied, flexible impeller pumps.
- Simple design means fewer wearing parts.
- ISO 8846 MARINE (Ignition protection).
- ISO 8849 MARINE (Bilge pump standard).
|
|
- Constructed from marine quality bronze and stainless steel for ruggedness and reliability.
- Easy to service and maintain.
- Inexpensive to buy and operate.
- Will tolerate abrasive wear (this may affect performance - seek advice from your distributer).
- Handles hard and soft solids without clogging.
- Can pump in either direction.
- Will not airlock.
|
|
|
The RHEINSTROM Impellerpumpe IP 50 can be used for the promotion of drinking water or waste water. The parts coming with water into contact are made of stainless material. The pump is positioninsensitive. It is sucking in drying. A longer unlubricated operation should be avoided however, since otherwise the Impeller could suffer damage. The pump is available in 12 V and 24V execution.
|
|
| ... products without information |
| |
| ... products without information |
| |
|
|
