|
|
Automatic high performance pump for deck and anchor wash down.
Self priming, for fresh or salt water use, automatic pump shut-off. |
|
| Flexible impeller pumps make excellent bilge pumps, principally because of their ability to handle bilge debris without damage. Because of the robust design many owners still use our 12 Volt dc or 24 Volt dc flexible impeller motor pump units that are up to 25 years old! Flexible Impeller Pumps also give the benefits of good flow, low cost, low size and weight, and are easily serviced and maintained. Most Flexible Impeller pumps must not be run dry, as this will damage the impeller which will require replacing. However, the Utility Puppy 2000 and 3000 both allow maximum of ten minutes dry running after initial prime. As with submersible pumps, flexible impeller pumps can be operated using a float or Hydro Air switch, and remotely controlled from outside the bilge compartment. There is a wide range of flexible impeller pumps to choose from giving a range of flows, discharge heads, and self-priming options for a wide variety of applications such as ballast transfer, bait tank circulation, and deck wash duties |
|
Flexi pumps have many applications, including:
• Emptying/filling water, oil or diesel.
• Bilge pumping
• Water circulation
The pumps can be combined with a vacuum switch that extends the life of the pump by saving battery capacity and preventing dry running. The pumps are self-priming and give full flow right from the start.
FDC900
Suitable pump for handling water, oil and diesel. Can be used as a bilge pump, flushing pump and for water
circulation on board.
FDC2700
Flushing, bilge and water circulation pump which is also highly suitable for handling water, oil and diesel. The mo-tor is rated for continuous operation at up to 1.2 bar (17 PSI) pressure.
|
|
SHURflo’s new Macerator pump is designed specifically for sanitation waste and fish box evacuations. This high-powered pump incorporates our high quality motor with a new seamless shell and splash proof design. Featuring a premium impeller design, including o-ring sealed end bells and sealed manual turn key. SHURflo’s unique dual blade and housing construction ensures problem free pumping. Delivering 13 GPM [49 LPM]. Thermally protected. Ignition protection. Available in 12 and 24 Volts.
|
|
| The SHURflo ULTRAflo Dual Head Pump is designed to give the ultimate in pumping capabilities; smooth high flow, minimal amp draw and easy electrical and plumbing connections. Optimal for high flow needs such as dual pump installations on larger boats, high flow washdown and high flow/low pressure continuous duty. |
|
- Suitable for diesel, fresh and salt water
- Quick diesel transfer with no spillage
- Water transfer, deck shower, or deck wash
- Continuous rating but should not be run dry for long periods
- Includes
- Spray Nozzle, 4m cable with battery clips, 4m layflat hose. |
|
| The powerful performance of VacuFlush sanitation systems centers on vacuum generator technology. Dometic's continuing development of vacuum generation systems is making VacuFlush a fast-growing name on more boats than ever. Choose from these vacuum-generating technologies. |
|
Specially engineered to greatly reduce sound emissions, SeaLand vacuum generators open new installation options for boatbuilders and renovators. Low-profile vacuum generator allows use in a wide range of hulls. Separate vacuum pump and tank components also add installation versatility.
|
|
| Self-priming diaphragm pump with 12v or 24v DC electric motor. |
|
| Self-priming diaphragm pump with 12v, 24v or 32v DC electric motor. Flow rates up to 17 litres/min (4.5 US gallons/min), pressure switch control, capable of pressures up to 3.2bar (45psi) |
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 18.9 litres/min (5 US gallons/min)
|
|
Shower and Sink Drain Pump
This single diaphragm pump is ideal for use in shower and sink drain applications. The filter-less design makes maintenance easy and is virtually unblockable. The pump has a compact design with multi positionable ports, which can make installation simple. 960 lph (254 US gph) output, self priming to 3m (10ft) and capable of extensive dry running, offering an inexpensive, reliable solution for shower and sink waste water.
http://www.jabsco.com/products/marine/sink_shower_drain_pumps/shower_drain_pump_50880_series/iid_2095/index.htm |
|
Water Pressure Pump
The new 2.9 and 1.9 models offer attractively priced solutions for craft with up to 3 hot and cold outlets, such as galley sink, hand basin and shower. The self priming, dry running, three chamber diaphragm design has a built-in bypass that gives smooth pulsation free flow, even at lower outputs, making an accumulator tank inessential. The quiet running motor is protected by a thermal overload cut-out, just like our more expensive models, and, of course, quick connect fittings are included.
|
|
| QL Water Pressure Pumps for water supply to the galley and shower - you just turn the tap or taps and the water flows. The water pressure pumps are suitable not only for fresh water but also for salt water. |
|
| Sanimarin Pump: essential to install a shower or a sink, Sanimarin Pump of SFA ensures the recovery of waste water on board boat. Its installation can be realized with the choice above or below the sea level thanks to a vertical repression going up to 4 meters and a diameter of repression from 22 to 32 Misters Robuste, it guarantees the raising of waste water of a maximum temperature of 35°C with a medium flow from approximately 50 l/mn. Of a consumption engine of 360 W, Sanimarin Pump offers the possibility of a power supply of 12 V or 24 V. Lastly, a dismountable external non-return valve ensure the good performance of the medical pump. |
|
There are two pumps in the system. One is an AC 220v pump which will, when there is AC power available (e.g. the generator is operating or the boat is connected to the dockside), automatically start working as soon as there is demand for water. The second pump is a DC 24v pump, which works from the battery banks.
When there is no AC power available, the system knows automatically to choose the latter pump. The unique feature of this DUO pump is that when water demand is very high, the intelligent system knows to operate both pumps at the same time, ensuring that you will never run out of water. A strong advantage of the DUO pump is that in the unlikely event that one pump breaks down, there is a second pump, standing by, as a backup.
This pump is readily available and comes in two different models, a 24vDC/220vAC-50Hz, suitable for the European market and a 24vDC/115-60Hz, suitable for the US market.
The AMFA Duo is compact and, as it is factory set, it is easy to install and is ideally suited to yachts of between 50ft - 70ft. As you would expect from an AMFA product from REYA, the fittings and piping are made from stainless steel ensuring a hard working, long lasting life. |
|
Ideal for single inboard/outboard sailboat or powerboat application
Single shut off Brass valve with adapters for 1/2" ID hose installation
Mounting plate for easy engine room installation
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps water, oil and diesel fuel
Built in fuse for motor protection |
|
Ideal for Two Engine Service - Either Two Engine, Engine / Generator or Diesel Engine / Transmission combination on Inboard sailboat or power boat applications
Two way shut off Brass valve with adapters for 1/2" ID hose installation
Mounting plate for easy engine room installation
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps water, oil and diesel fuel
Built in fuse for motor protection |
|
Ideal for portable use or can be permanently installed
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps oil, diesel or water
Built in fuse for motor protection |
|
Ideal for portable use on Outboards, Stern Drives, or 4 Stroke PWC's or can be Permanently Installed
4' Dipstick & Drain Tubing
8' Power Cords with Alligator Clips
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps oil, diesel or water
Built in fuse for motor protection |
|
The Johnson Pump TA3P10-19 Macerator pump takes care of the toilet waste, shredding it before it is pumped into or out from the holding tank.
Features
- Ignition protected motor, conforming with ISO 8846 Marine
- Mounting bracket for easy replacement
- Extremely energy efficient
- Rotary cutter casing of PET (thermoplastic polyester)
- Directly connected to sewage line or holding tank |
|
Ideal for Twin Inboard / Single Generator boats either Gas or Diesel
Also applicable for Single Diesel Engine / Transmission and Generator (trawlers, sailboats, work boats)
Enclosed in a molded housing provided excellent engine room presentation
Mounting plate for easy engine room installation
Self priming impeller driven reversible pump for drain and fill applications
12 or 24 Volt motors available
Pumps water, oil and diesel fuel
Built in fuse for motor protection |
|
Compact shower drain, bilge and waste water pump
Specifically designed to pump waste water, the Viking Power 16 is an ultramodern, single-chamber self-priming diaphragm pump that can be set up in several different pump/motor configurations.
Perfect for installation in tight spaces, the Viking Power 16 can be installed anywhere after the drain outlet in the wastewater system or as a bilge pump in any leisure craft -- new or used. Compact, robust and adaptable the Viking Power 16 has KlickTite%u2122 XL connectors fitted as standard, literally making hose connections a snap! (Delivered with 1" & 3/4" hose and 1/2" BSP (NPT) KlickTite%u2122 XL connectors.)
The Viking Power 16 features non-choke valves, which means that no in-line filters are necessary. The pump can not only be run dry, it can also handle a mixture of air and water without difficulty. The Viking Power 16 is self-priming up to a height of 3 meters.
With its low pulse and muffled rubber bracket, this pump offers quiet operation. The Viking Power 16 has been built to last, and engineered for easy maintenance. When it comes time to replace the premium grade reinforced nitrile rubber diaphragm, you can put in a spare without even removing the pump from the system.
|
|
Aqua Jet WPS 2.9, 3.5, 4.0 & 5.2 and Flowmaster 5.0
The new generation of WPS pumps - 12V or 24V DC. Quiet and pulsation-free even at low speeds, the new Aqua Jet five-chamber diaphragm pump from Johnson Pump provides the perfect water pressure solution for both small and medium sized leisure and commercial boats.
NEW! WPS 3.5 Fitted with a built-in pulsation dampening by-pass to control unwanted cycling and noise. |
|
| The RHEINSTROM Impellerpumpe IP 50 can be used for the promotion of drinking water or waste water. The parts coming with water into contact are made of stainless material. The pump is positioninsensitive. It is sucking in drying. A longer unlubricated operation should be avoided however, since otherwise the Impeller could suffer damage. The pump is available in 12 V and 24V execution. |
|
| The Rhine current diverter pump telex 370 is a large, expresses robust and chopper pump suitable for the permanent run. It is not sucking in and must be cultivated by from there either in the deepest place of the tank or be installed more deeply than the tank. A chopper is before-built for the actual pump part, which cuts the material to be conveyed up very finely. In case of maintenance the pump body can be divided very easily and with simple means. Contrary to the diverter pump F it is suitable for continuous operation. From there it Fäkalientanks up to a size of approx. 1 m ³ are ideal for this pump. |
|
| A spring and a deck wash pump, which are suitable also for the promotion of seawater. By its special construction this Rhine current pump is insensitive to the admixture of sand (grain size up to 6 mm), rust or other pollutants. The use of an unsolicited impeller and a most modern axial face seal make nearly completely maintenance-free this pump. The engine is appropriate for continuous operation. We suggest, with the installation, building into the sucking in line a foot or a sleeve setback valve. The pump needs to be filled by this measure only before first start-up with liquid. A refilling up when tearing the liquid column off is not necessary from there. Also air cushions in the line system do not impair the working reliability of the pump. |
|
|
|
