|
|
|
The M 60 is a self-priming and smoothly running diaphragm pump used for various purposes. All parts which come into contact with liquids are made of bronze or stainless steel. The used rubber parts are oil-resistant. The pump is non-reactive to running dry and very suitable for continuous operation. The M 60 is equipped with flap valves. Therefore it can convey bigger solids such as rags. The pump can be mounted in various ways, etc. lying, upright, above head or hanging on the wall. The delivery side can be adjusted from left to right, or right to left or from up to down and down to up. The fields of operation of the M 60 are on bigger yachts or in professional shipping as a hard-wearing bilge pump.
|
|
The sewage pump M is a self-priming diaphragm pump. It works without a macerator. Even bigger solids can be conveyed without damaging the pump because of the lip valves which have been installed. The self-locking valves make the pump non-reactive, i.e. it can be mounted to the side standing, hanging or sideways. The intake and discharge bent is revolving. This is necessary for better connecting possibilities of the suction and pressure hoses. The suction and pressure connections usually go from left to right. They can easily be changed, if the suction way should go from right to left or from the bottom to the top. All parts which come into contact with water can be ordered in red brass or aluminium. The pump can be delivered with a 12 V or 24 V motor.
Continuous operation 1 – 2 hours max.
Attention: The cross section of the pipe should never be less than 1 ½”/ 38 mm – or the pump capacity will not be achieved.
|
|
Performance:
Static Suction Lift:
15 ft / 4.57m
Dry Suction Lift:
12 ft / 3.65m
Discharge Head:
15 ft / 4.57m
Max Volume:
40 GPM / 152 LPM(at 60 cycles per minute)
Construction:
Pump Base
(Wetted Parts)
Choice of:
Anodized Aluminum
Marine Bronze
Urethane Powder Coating
PTFE Coating (HALAR)
Diaphragms and Valves
Choice of:
Nitrile
Viton
Hypalon
Mounting Frame:
Powder Coated Aluminum
Hardware Material:
Stainless Steel
Drives:
Gasoline Powered:
Close Coupled 3.5hp Gasoline Engine
|
|
Features:
- Compact Design Measuring 6.4" (162 mm) in Length
- Fully Automatic Demand Pump
- Self-priming and Can Operate Dry Without Damage
- Built-in Thermal Protector
- Sealed Pressure Switch and Motor
- Flow Rates to 1.0 GPM (3.8 L/min.) and Operating Pressures to 25 PSI (1.7 bar)
- Compact automatic demand pump.
- Sealed pressure switch automaticatly starts and stops pump when discharge valve is opened and closed.
- Self-prlming so pump can be located above supply tank.
- Can run dry for extended periods of time without damage.
- Built-in thermal protector
- Low amp draw for battery powered applications.
- Soft compliant Santoprene mounting system.
|
|
Performance:
Static Suction Lift:
15 ft / 4.57m
Dry Suction Lift:
12 ft / 3.65m
Discharge Head:
15 ft / 4.57m
Max Volume:
40 GPM / 152 LPM (at 60 cycles per minute)
Construction:
Pump Base:
(Wetted Parts)
Choice of:
Anodized Aluminum
Marine Bronze
Urethane Powder Coating
PTFE Coating (HALAR)
Diaphragms and Valves:
Choice of:
Nitrile
Viton
Hypalon
Mounting Frame:
Powder Coated Aluminum
Hardware Material:
Stainless Steel
Drives:
Electric Powered with Choice of Close Coupled:
3/4 hp tefc motors all voltages, 1ph or 3ph
3/4 hp explosion-proof motors
3/4 hp teft 12v and 24v motors
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 18.9 litres/min (5 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
Includes strainer, 3/4" hose barb and 3/4" garden hose ports
|
|
Self-priming diaphragm pump with 12v, 24v or 32v DC electric motor. Flow rates up to 17 litres/min (4.5 US gallons/min), pressure switch control, capable of pressures up to 3.2bar (45psi)
Features
Self-primes up to 2.4m vertical lift
Four-piston design delivers higher flow rates
Quick-connect plug-in ports for easy installation
Pressure-switch control to run the pump only as needed
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 12.5 litres/min (3.3 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
Oil resistant elastomers - suitable for diesel transfer
|
|
Features:
Compact Design Measuring 6.4" (162 mm) in Length
Fully Automatic Demand Pump
Self-priming and Can Operate Dry Without Damage
Built-in Thermal Protector
Sealed Pressure Switch and Motor
Flow Rates to 1.0 GPM (3.8 L/min.) and Operating Pressures to 25 PSI (1.7 bar)
Compact automatic demand pump.
Sealed pressure switch automaticatly starts and stops pump when discharge valve is opened and closed.
Self-prlming so pump can be located above supply tank.
Can run dry for extended periods of time without damage.
Built-in thermal protector
Low amp draw for battery powered applications.
Soft compliant Santoprene mounting system.
|
|
| ... products without information |
| |
Performance:
Static Suction Lift:
15 ft / 4.57m
Dry Suction Lift:
12 ft / 3.65m
Discharge Head:
15 ft / 4.57m
Max Volume:
40 GPM / 152 LPM (at 60 cycles per minute)
Construction:
Pump Base:
(Wetted Parts)
Choice of:
Anodized Aluminum
Marine Bronze
Urethane Powder Coating
PTFE Coating (HALAR)
Diaphragms and Valves:
Choice of:
Nitrile
Viton
Hypalon
Mounting Frame:
Powder Coated Aluminum
Hardware Material:
Stainless Steel
Drives:
Electric Powered with Choice of Close Coupled:
3/4 hp tefc motors all voltages, 1ph or 3ph
3/4 hp explosion-proof motors
3/4 hp teft 12v and 24v motors
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 18.9 litres/min (5 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
Includes strainer, 3/4" hose barb and 3/4" garden hose ports
|
|
Self-priming diaphragm pump with 12v, 24v or 32v DC electric motor. Flow rates up to 17 litres/min (4.5 US gallons/min), pressure switch control, capable of pressures up to 3.2bar (45psi)
Features
Self-primes up to 2.4m vertical lift
Four-piston design delivers higher flow rates
Quick-connect plug-in ports for easy installation
Pressure-switch control to run the pump only as needed
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 12.5 litres/min (3.3 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
Oil resistant elastomers - suitable for diesel transfer
|
|
Features:
Compact Design Measuring 6.4" (162 mm) in Length
Fully Automatic Demand Pump
Self-priming and Can Operate Dry Without Damage
Built-in Thermal Protector
Sealed Pressure Switch and Motor
Flow Rates to 1.0 GPM (3.8 L/min.) and Operating Pressures to 25 PSI (1.7 bar)
Compact automatic demand pump.
Sealed pressure switch automaticatly starts and stops pump when discharge valve is opened and closed.
Self-prlming so pump can be located above supply tank.
Can run dry for extended periods of time without damage.
Built-in thermal protector
Low amp draw for battery powered applications.
Soft compliant Santoprene mounting system.
|
|
| ... products without information |
| |
The sewage pump M is a self-priming diaphragm pump. It works without a macerator. Even bigger solids can be conveyed without damaging the pump because of the lip valves which have been installed. The self-locking valves make the pump non-reactive, i.e. it can be mounted to the side standing, hanging or sideways. The intake and discharge bent is revolving. This is necessary for better connecting possibilities of the suction and pressure hoses. The suction and pressure connections usually go from left to right. They can easily be changed, if the suction way should go from right to left or from the bottom to the top. All parts which come into contact with water can be ordered in red brass or aluminium. The pump can be delivered with a 12 V or 24 V motor.
Continuous operation 1 – 2 hours max.
Attention: The cross section of the pipe should never be less than 1 ½”/ 38 mm – or the pump capacity will not be achieved.
|
|
|
|
