|
|
|
|
|
|
|
DC Driven Flexible Impeller Pumps
Pumps suited for use in boats as bilge and deckwash pumps, fresh water pumps, refuelling pumps for oil and diesel. Can be combined with a vacuum switch for automatic operation. Capacities vary from max 14 l/min to 55 l/min, allowing the proper matching of the pump to the application. All motors are heavy duty to provide long service life even under heavy use.
F3B-19 F38B-19 F4B-19 F5B-19
Perfect for bilge pumping, deckwash, water circulation, oil and diesel refuelling at dockside service, etc.
F3B-19 Oil Change
Reversible rubber impeller pump with integrated quick reversing switch. Designed to remove old oil from the engine/fill new oil back into theengine.
F4B-11 Ultra Ballast
Designed to quickly fill or, when reversed, drain a ballast tank at a rate of more than 45 l/min (12 GPM). Capable of pumping fresh or sea water the pump's robust design can handle the rigors of continuous duty usage, is reversible, and has a built in thermal overload for added protection. Care not to run dry for extended periods of time will increase the pump longevity and ensure reliable performance for many years.
Note! Only for waterhandling.
|
|
A line of compact magnetic driven centrifugal pumps, CM-series, which combine high flow rates with very low electric current consumption, making them ideally suited for circulating fresh water in live fish tanks, heating and cooling systems. C090 with mechanical seal and a motor designed for continuous operation.
Designed also for fresh water handling.
|
|
Dometic marine holding tank system – a clean and easy solution to fit every boat
“Fit-and-forget” pump design – Dometic DTW-series waste discharge pumps are based on a unique bellows design that makes them last longer than other manufacturers’ rubber diaphragm pumps. Running quietly, they easily handle over 1000 litres of waste per hour. Available for either 12 or 24 volts DC.
Waste discharge pump
› Long-life bellows design
› Quiet operation
› Runs dry without damage
› Handles liquids and solids
|
|
POSSIBLE CONNECTIONS
Shower, sink
VERTICAL PUMPING HEIGHT UP TO
4 m
OUTLET DIAMETER
22 mm to 32 mm
MAX WASTE WATER TEMPERATURE
35°C
SUPPLY VOLTAGE
12 V or 24 V
MOTOR POWER RATING
360 W
|
|
Viking Power 16
A modern, single-chamber, self-priming diaphragm pump that can be set up in several different pump/motor configurations. It is easy to install anywhere after the drain outlet in the wastewater system or as a bilge pump in any leisure craft – new or used.
Its non-choke valves mean that no in-line filters are necessary. The pump can be run dry, and it can also handle a mixture of air and water without difficulty. The Viking Power 16 is self-priming up to a height of 3 meters.
With its low pulse and muffled rubber bracket, this pump offers quiet operation. Specifically designed to pump waste water, the Viking Power 16 has been built to last, and engineered for easy maintenance. When it comes time to replace the premium grade reinforced nitrile rubber diaphragm, you can put in a spare without even removing the pump from the system. Delivered with 1” hose and ¾” hose ½” BSP KlickTite™ XL connectors. 90° KlickTite™ XL connectors available as extra accessory.
|
|
Macerator Pump
The TA3P10-19 macerator pump takes care of toilet waste. A rotary cutter shreds waste before it is pumped into or out from the holding tank. The pump should be connected as close as possible to the holding tank discharge outlet or the bowl discharge outlet. Note! Use unbleached lavatory paper only.
|
|
Aqua Jet Wash Down Pumps
As a wash down pump, the Aqua Jet offers much higher pressures than competitive models, making clean-up faster and easier than ever before.
Aqua Jet Wash Down Pump Kit 5.2
20 l/min (5.2 GPM) wash down kit conveniently includes a high capacity Aqua Jet WD 5.2, 5 bar (70 psi), PUMProtector inlet strainer, spray nozzle, bulk head fitting with valve, 7.5 meters (25’) of coiled wash down hose and an illuminated panel switch – all in one package.
|
|
It is sad to say, but the average deckwash pump can do with a lot of improvement. Too little pressure and a rather lame water flow are typical for the common deckwash pump in the market. WillDo has designed a pump which gives a powerful water jet, which will allow you to wash your deck really properly. Driven by a sturdy 12V electric motor, which can be connected directly to a battery, you will be able to use the unit continuously during at least 20 minutes. The build-in pressure cut-off makes its handling very practical and enhances the life span of pump, motor and battery. The materials used are top quality and the pump can be used with sweet water and sea water alike.
This pump unit is also excellently suited for use
as a fire fighting pump on your boat in an emergency case.
|
|
|
The M 60 is a self-priming and smoothly running diaphragm pump used for various purposes. All parts which come into contact with liquids are made of bronze or stainless steel. The used rubber parts are oil-resistant. The pump is non-reactive to running dry and very suitable for continuous operation. The M 60 is equipped with flap valves. Therefore it can convey bigger solids such as rags. The pump can be mounted in various ways, etc. lying, upright, above head or hanging on the wall. The delivery side can be adjusted from left to right, or right to left or from up to down and down to up. The fields of operation of the M 60 are on bigger yachts or in professional shipping as a hard-wearing bilge pump.
|
|
The sewage pump M is a self-priming diaphragm pump. It works without a macerator. Even bigger solids can be conveyed without damaging the pump because of the lip valves which have been installed. The self-locking valves make the pump non-reactive, i.e. it can be mounted to the side standing, hanging or sideways. The intake and discharge bent is revolving. This is necessary for better connecting possibilities of the suction and pressure hoses. The suction and pressure connections usually go from left to right. They can easily be changed, if the suction way should go from right to left or from the bottom to the top. All parts which come into contact with water can be ordered in red brass or aluminium. The pump can be delivered with a 12 V or 24 V motor.
Continuous operation 1 – 2 hours max.
Attention: The cross section of the pipe should never be less than 1 ½”/ 38 mm – or the pump capacity will not be achieved.
|
|
|
The Rheinstrom sewage pump FS 370 is a big, very hard wearing macerator pump which is suitable for continuous operation. It is not self-priming and therefore it must be installed either at the lowest part of the tank or lower than the tank itself. A macerator which chops up the conveying means is mounted in front of the pump. In case maintenance has to be carried out the pump’s body can easily be taken apart. In contrast to the sewage pump F the sewage pump FS 370 is suitable for continuous operation. Sewage tanks up to a size of 1 m³ are ideal for this pump.
|
|
Performance:
Static Suction Lift:
15 ft / 4.57m
Dry Suction Lift:
12 ft / 3.65m
Discharge Head:
15 ft / 4.57m
Max Volume:
40 GPM / 152 LPM(at 60 cycles per minute)
Construction:
Pump Base
(Wetted Parts)
Choice of:
Anodized Aluminum
Marine Bronze
Urethane Powder Coating
PTFE Coating (HALAR)
Diaphragms and Valves
Choice of:
Nitrile
Viton
Hypalon
Mounting Frame:
Powder Coated Aluminum
Hardware Material:
Stainless Steel
Drives:
Gasoline Powered:
Close Coupled 3.5hp Gasoline Engine
|
|
Features:
- Compact Design Measuring 6.4" (162 mm) in Length
- Fully Automatic Demand Pump
- Self-priming and Can Operate Dry Without Damage
- Built-in Thermal Protector
- Sealed Pressure Switch and Motor
- Flow Rates to 1.0 GPM (3.8 L/min.) and Operating Pressures to 25 PSI (1.7 bar)
- Compact automatic demand pump.
- Sealed pressure switch automaticatly starts and stops pump when discharge valve is opened and closed.
- Self-prlming so pump can be located above supply tank.
- Can run dry for extended periods of time without damage.
- Built-in thermal protector
- Low amp draw for battery powered applications.
- Soft compliant Santoprene mounting system.
|
|
Performance:
Static Suction Lift:
15 ft / 4.57m
Dry Suction Lift:
12 ft / 3.65m
Discharge Head:
15 ft / 4.57m
Max Volume:
40 GPM / 152 LPM (at 60 cycles per minute)
Construction:
Pump Base:
(Wetted Parts)
Choice of:
Anodized Aluminum
Marine Bronze
Urethane Powder Coating
PTFE Coating (HALAR)
Diaphragms and Valves:
Choice of:
Nitrile
Viton
Hypalon
Mounting Frame:
Powder Coated Aluminum
Hardware Material:
Stainless Steel
Drives:
Electric Powered with Choice of Close Coupled:
3/4 hp tefc motors all voltages, 1ph or 3ph
3/4 hp explosion-proof motors
3/4 hp teft 12v and 24v motors
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 12.5 litres/min (3.3 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
Oil resistant elastomers - suitable for diesel transfer
|
|
Self-priming diaphragm pump with 12v, 24v or 32v DC electric motor. Flow rates up to 17 litres/min (4.5 US gallons/min), pressure switch control, capable of pressures up to 3.2bar (45psi)
Features
Self-primes up to 2.4m vertical lift
Four-piston design delivers higher flow rates
Quick-connect plug-in ports for easy installation
Pressure-switch control to run the pump only as needed
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 18.9 litres/min (5 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
Includes strainer, 3/4" hose barb and 3/4" garden hose ports
|
|
Features:
Compact Design Measuring 6.4" (162 mm) in Length
Fully Automatic Demand Pump
Self-priming and Can Operate Dry Without Damage
Built-in Thermal Protector
Sealed Pressure Switch and Motor
Flow Rates to 1.0 GPM (3.8 L/min.) and Operating Pressures to 25 PSI (1.7 bar)
Compact automatic demand pump.
Sealed pressure switch automaticatly starts and stops pump when discharge valve is opened and closed.
Self-prlming so pump can be located above supply tank.
Can run dry for extended periods of time without damage.
Built-in thermal protector
Low amp draw for battery powered applications.
Soft compliant Santoprene mounting system.
|
|
- Constructed from marine quality bronze and stainless steel for ruggedness and reliability.
- Easy to service and maintain.
- Inexpensive to buy and operate.
- Will tolerate abrasive wear (this may affect performance - seek advice from your distributer).
- Handles hard and soft solids without clogging.
- Can pump in either direction.
- Will not airlock.
|
|
Flow rate: 32 Litres/min (6.5 gallons/min)
Self-priming from dry up to 1.2m (4ft)
- Small bilge debris present no problem to these bronze bodied, flexible impeller pumps.
- Simple design means fewer wearing parts.
- ISO 8846 MARINE (Ignition protection).
- ISO 8849 MARINE (Bilge pump standard).
|
|
Features:
- Small bilge debris present no problem to these bronze bodied, flexible impeller pumps.
- Simple design means fewer wearing parts.
- ISO 8846 MARINE (Ignition protection).
- ISO 8849 MARINE (Bilge pump standard).
|
|
|
QL pumps are versatile and therefore ideal as deckwash and bilge pumps, for pumping fresh water and diesel fuel. The combination of a Vac-on-Switch provides extended battery life as well as preventing the pump from running dry.
|
|
- Quiet operation
- Runs dry without damage
- Inlet strainer included
- Quick Connect ports with adaptors included
- Suitable for use with saltwater and freshwater
- Self-priming up to 3 m (10 ft)
- Smooth constant flow
- Extra protection and safety with wires and pressure switch
housed internally
- Universal mounting arrangement fits any existing installation
|
|
|
Self-priming pump, fitted with neoprene rotors; watertight in accordance with ISO 8846 standards (may be installed on the engine room) - Version A: Electrophoresis enamelled engine casing - Version B: Model MKII fitted with pump unit made of resin-thermosetting reinforced fibre glass + stainless steel internal inserts.
|
|
- Suitable for diesel, fresh and salt water
- Quick diesel transfer with no spillage
- Water transfer, deck shower, or deck wash
- Continuous rating but should not be run dry for long periods
- Includes
- Spray Nozzle, 4m cable with battery clips, 4m layflat hose.
|
|
Edson Air Powered Diaphragm Pumps are the most
versatile of all Edson Pumps due to the flexibility of
the air cylinder drive. They are used for the collection
and transfer of waste liquids and pumping liquids with
suspended solids. They are capable of handling
liquids with large suspended solids without clogging,
to prime from dry starts, and to run dry. They have
the added feature of low emulsive, non sheering
pumping action. These basic performance features
and Edson’s 140 year history of manufacturing quality
products have made our pumps the choice for cleaning
up our environment and controlling the disposal of
liquid waste. Evident by the list of applications the
pumps can be used including the requirements for
ground water remediation, containment transfers,
dewatering, oil and water separations, marina and
campground sewage collection, tank, sump and drum
transfers, filtration applications, and the collection and
transfer of abrasives, slurries.
|
|
Features:
Variable Speed Control
Solid State Pressure Sensor
Nearly Silent Operation / No Cycling
Operates on l2Vdc or 24Vdc
Controls Pressure by Changing Motor Speed
Speeds Up As Demand Increases
Self-priming / Runs Dry
No Accumulator Tank Needed
CSA Listed / EN ISO 8846 Marine / C.E. Certified
Specifications:
Motor Permanent magnet, double ball bearing armature. Electronic speed control built into rear endbell.
Pump Four chamber positive displacement diaphragm design. Self-priming up to 10 feet suction lift. Pump able to run dry without damage. Removable port adapters.
|
|
|
Self-priming diaphragm pump with 12v, 24v or 32v DC electric motor. Flow rates up to 17 litres/min (4.5 US gallons/min), pressure switch control, capable of pressures up to 3.2bar (45psi)
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor.
Features:
• Self-primes up to 10ft (3m) vertical lift
• Runs dry without damage to the pump
• Quick-connect plug-in ports for easy installation
• Oil resistant elastomers - suitable for diesel transfer
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 18.9 litres/min (5 US gallons/min)
|
|
|
|
