|
|
|
12 volt submersible bilge pumps are constructed of shock resistant A.B.S. plastic, and powered by the world's best compact motor. The snap-on strainer base makes installation a simple procedure. These reliable pumps are available in four sizes from 500gph to 1000gph.
|
|
Cartridge Bilge Pumps L450 - L750 Series
L650 and L750 incorporate some of the most advanced features in the industry, features developed from service in a wide variety of uses including racing, cruising, sport fishing, and demanding commercial duties.
For L450, L550, and L650, we have improved the design with easy-to-install Dura-Port discharge ports to eliminate stress cracking caused by over-tightened hose clamps. The pumps are delivered including both a straight and a 90° smooth elbow Dura-Port as well as a removable check valve.
|
|
Ultima Bilge Pump
Sleek, reliable and compact unit with integrated switch ready to install and run for years and years of unerring service. Available in 600-800-1000-1250 GPH versions. Voltage12 V DC.
For UltimaBilge™ 600 GPH-1000 GPH, we have easy-to-install Dura-Port discharge ports to eliminate stress cracking caused by over-tightened hose clamps. The pumps are delivered including both a straight and a 90° smooth elbow Dura-Port and a removable check valve.
|
|
Heavy Duty Bilge Pump – L1600 - L4000 Series
Designed to meet and exceed the tough demands of commercial and recreational duty. This pump has a liquid cooled, 12-pole motor with double ball bearings for extended service life.
The L2200 motor is sealed off by a mechanical seal design that eliminates shaft wear and allows for service and replacement, while the L1600 model has lipseal.
The impeller is carefully designed and tested to maximize head and flow.
The L4000 features a robust motor design, mechanical shaft seal, high impact ABS plastic and unique threaded port design. Universal base plate and a choice of 1.½” or 2” ports makes for a simple installation. Removable check valve included.
|
|
Ultima Combo
Pump with automatic operation equipped with the Ultima switch. Voltage12 V DC as well as 24 V DC for L650 UC and L750 UC.
For L450 UC - L650 UC, we have easy-to-install Dura-Port discharge ports to eliminate stress cracking caused by over-tightened hose clamps. The pumps will be delivered including both a straight and a 90° smooth elbow Dura-Port as well as a removable check valve.
|
|
High pumping capacity and reliability at a lower cost. The Rule 1500 offers more pumping capacity and more exclusive design features than any comparable competitive pump. 1-1/8" (28.6mm) discharge outlet. 12 Volts DC unless noted.
|
|
Rule's 700 and 750 G.P.H. Pumps offer increased capacity in keeping with it's 3/4" (19mm) discharge outlet. 12 Volts DC unless noted.
|
|
Attwood’s pumps play no "rating games" like competitive pumps. Attwood electric bilge pumps deliver value and performance that’s built to last.
|
|
Self-priming diaphragm pump with 12v or 24v DC electric motor. Flow rates up to 18.9 litres/min (5 US gallons/min)
Features:
Self-primes up to 10ft (3m) vertical lift
Runs dry without damage to the pump
Quick-connect plug-in ports for easy installation
Includes strainer, 3/4" hose barb and 3/4" garden hose ports
|
|
A very compact, powerful pump which is ideal for the hard life of working boats. This pump can lift up to 130 litres per minute (to free outlet) and is available for 12 and 24 V.
The motor has double roller bearings, and a mechanical seal virtually eliminates shaft wear. This, together with water cooling, helps to ensure many years of trouble free life with very low power consumption.
|
|
|
The Rule 500 offers many design features while keeping size and cost to a minimum. Especially popular on smaller craft, Rule 500 pumps are unmatched in pumping power and longevity.
|
|
|
Engineered to commercial standards. The Rule 2000 is the best selling high capacity submersible bilge pump in the world. 1-1/8" (28.6mm) discharge outlet. 12 Volts DC unless noted.
|
|
|
High pumping capacity and reliability at a lower cost. The Rule 1500 offers more pumping capacity and more exclusive design features than any comparable competitive pump. 1-1/8" (28.6mm) discharge outlet. 12 Volts DC unless noted.
|
|
|
Quality bilge pumps you can trust. SHURflo’s bilge pumps are built for the harsh marine environment to withstand the toughest conditions. Standard with 3’ Tinned Wire Assembly for above waterline installations and water cooled motors for extended life. .
|
|
Technical specifications:
Electric motor: three-phase induction motor MEC T63C4 or single-phase induction motor MEC M63C2
Power supply: 230 V / 400 V – 50 Hz depending upon the model
Power output: 0.22 kW / 0.25 kW depending upon the model
Absorbed current: 1.6 A / 1.4 A depending upon the model
Protection rating: IP 55
Condenser: 10 µF
Speed of motor rotation: 1,380 rpm / 2,800 rpm depending upon the model
Maximum pressure: 20 bar
Capacity: ranging from 5 to 22 litres / minute
Data referring to the following test fluid: oil with viscosity n =13 cSt and temperature ranging between 15°C and 20°C
|
|
| ... products without information |
| |
Macerator Pump
The TA3P10-19 macerator pump takes care of toilet waste. A rotary cutter shreds waste before it is pumped into or out from the holding tank. The pump should be connected as close as possible to the holding tank discharge outlet or the bowl discharge outlet. Note! Use unbleached lavatory paper only.
|
|
The sewage pump M is a self-priming diaphragm pump. It works without a macerator. Even bigger solids can be conveyed without damaging the pump because of the lip valves which have been installed. The self-locking valves make the pump non-reactive, i.e. it can be mounted to the side standing, hanging or sideways. The intake and discharge bent is revolving. This is necessary for better connecting possibilities of the suction and pressure hoses. The suction and pressure connections usually go from left to right. They can easily be changed, if the suction way should go from right to left or from the bottom to the top. All parts which come into contact with water can be ordered in red brass or aluminium. The pump can be delivered with a 12 V or 24 V motor.
Continuous operation 1 – 2 hours max.
Attention: The cross section of the pipe should never be less than 1 ½”/ 38 mm – or the pump capacity will not be achieved.
|
|
|
The Rheinstrom sewage pump FS 370 is a big, very hard wearing macerator pump which is suitable for continuous operation. It is not self-priming and therefore it must be installed either at the lowest part of the tank or lower than the tank itself. A macerator which chops up the conveying means is mounted in front of the pump. In case maintenance has to be carried out the pump’s body can easily be taken apart. In contrast to the sewage pump F the sewage pump FS 370 is suitable for continuous operation. Sewage tanks up to a size of 1 m³ are ideal for this pump.
|
|
|
|
|
|
|
WASTE EVACUATION
The Jabsco 18590 series DC macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operation
It is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage.
FISH BOX AND LIVEWELL TANK EVACUATION
The Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties.
Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats.
|
|
|
SHURflo’s Macerator pump is designed specifically for sanitation waste and fish box evacuations providing superior performance in harsh marine environments.
|
|
|
SHURflo’s Macerator pump is designed specifically for sanitation waste and fish box evacuations providing superior performance in harsh marine environments.
|
|
- Self-priming to a lift of six feet
- Flow rate to 6-1/2 gallons per minute
- Rated for continuous duty cycles of up to 1/2 hour ofuninterrupted pumping time (nearly 200 gallons ofsewerage transfer per cycle)
- Motor meets USCG regulation 183.410 and ISO 8846MARINE for ignition protection
- Motor is EMC compliant and CE marked
- Ports accept 1-1/2" hose with room for double bandclamps
- All pump components (non-flexible) are non-corrosiveplastic, stainless steel and bronze
- Diaphragm is made of Santoprene and the valves aremade of nitrile
- Pump housing is made of glass filled nylon
- The motor and gear drive are painted with a durableprotective coating
- A plastic motor splash guard adds additional protection
|
|
|
SANISPLIT is an automatic soil and waste water pumping unit, which collects the water from the kitchen and bathroom and pumps it into the collection tanks, even without the necessary gradient. SANISPLIT includes a powerful and silent centrifugal pump controlled by a pressure switch, which starts the pump as soon as the water arrives in the unit's collection tank.
|
|
Features:
- High head capability - 10 metres (32 feet.)
- Self priming up to 3 metres (9.6 feet.)
- Continuously rated
- Vibration tested
- IP55 protected motor
- 24V version with thermal cut-out protection
- Full range of installation accessories
- Customised kits for OEM customers
- ISO8846 Marine (Ignition Protection)
|
|
| ... products without information |
| |
Livewell Pumps
“C” Tournament SeriesTM Removable Motor Cartridge NEW!
For Thru-Hull ApplicationsAngled 4" (102mm) Pickup Tube.
|
|
The Pro Baitmaster™ is excellent for Livewell or Washdown applications to withstand the harsh marine environment. The seamless motor shell and sealed switch protects the pump from splashed liquids. This pump is ideal in areas that have limited mounting space, where separate Washdown and Livewell pumps do not fit. The Pro Baitmaster is rated for tanks up to 35 gallons.
SHURflo’s next generation Pro Baitmaster™ livewell pumps are versatile for dual-purpose applications. They are excellent for livewell applications and can be used as a washdown pump in harsh marine environments. The SHURCoat II seamless shell motor and sealed switch protects the pump from splashed liquids.
|
|
|
|
see the results for the following category : 
