|
|
The charge regulator CRM is especially suitable for marine applications. It is completely sealed and thus effectively protected against the marine environment.
The regulator has two separate outputs, which can be used to charge two battery sets separately (eg. starter battery and service battery on a yacht). The two outputs can be connected together if only a single battery shall be charged. More than two separate battery sets are charged by wiring additional diode units between the batteries. For adaption to different types of batteries the charging voltage can be adjusted in a range of +/- 20 % |
|
The CR30W is a sophisticated charge regulator for 12 V or 24 V DC small wind applications based on a special micro-controller.
The regulation is done by a shunt load (power resistors) which is switched by the regulator to prevent overcharging. Therefore the wind generator can be connected directly to the battery and never runs unloaded.
The micro controller together with a smart electronic circuit provides high-efficiency charging technology combined with a reduction in the number of electronic components. Therefore excellent battery treatment is now available at reasonable cost and with outstanding reliability even at tough environmental conditions.
|
|
The Alfatronix IC Series is suitable for charging all types of lead acid batteries using a 3 stage system. They are enclosed in a rugged, anodized aluminium extrusion and sealed to IP67 and can be installed practically anywhere on boats or vehicles, on road or off and at depots or garages.
These battery chargers offer an ideal solution where a compact charger is required to operate in hostile environments. |
|
Intelligent Battery Chargers
The IC Series Intelligent Battery chargers offer an ideal way of charging any type of lead acid battery safely and reliably.
The rugged fully protected unit (IP67) can be used in a variety of applications including on trucks, off road vehicles, fire vehicles, boats, caravans and in depots and workshops. |
|
Install Mastervolt battery chargers and rest assured that your on board batteries are always quickly and completely charged, even when you have limited supply or are moored in marinas with low shore power.
Mastervolt's three-step charging method guarantees optimum efficiency. Your batteries will perform better and last much longer. |
|
Important advantages:
- Multiple outputs in order to charge more groups of batteries (internal battery isolator diodes).
- Charge selector for liquid/gel electrolyte batteries.
- Low residual fluctuation on output (ripple lower than 30 mV RMS).
- Compatible with every kind of generator.
- Can work in a wide range of ambient temperatures.
3 Step automatic charge:
BULK phase (constant current)
ABSORPTION phase (constant voltage)
FLOAT phase (maintenance)
Universal AC Network: models DR
Protections:
- Reverse polarity (with internal fuse)
- Overload
- Output short circuit
- Overheating |
|
Important advantages:
- Multiple outputs in order to charge more groups of batteries (internal battery isolator diodes).
- Charge selector for liquid/gel electrolyte batteries.
- Low residual fluctuation on output (ripple lower than 30 mV RMS).
- Compatible with every kind of generator.
- Can work in a wide range of ambient temperatures.
3 Step automatic charge:
BULK phase (constant current)
ABSORPTION phase (constant voltage)
FLOAT phase (maintenance)
Universal AC Network: models DR
Protections:
- Reverse polarity (with internal fuse)
- Overload
- Output short circuit
- Overheating |
|
Important advantages:
- Multiple outputs in order to charge more groups of batteries (internal battery isolator diodes).
- Charge selector for liquid/gel electrolyte batteries.
- Low residual fluctuation on output (ripple lower than 30 mV RMS).
- Compatible with every kind of generator.
- Can work in a wide range of ambient temperatures.
3 Step automatic charge:
BULK phase (constant current)
ABSORPTION phase (constant voltage)
FLOAT phase (maintenance)
Universal AC Network: models DR
Protections:
- Reverse polarity (with internal fuse)
- Overload
- Output short circuit
- Overheating |
|
Important advantages:
- Multiple outputs in order to charge more groups of batteries (internal battery isolator diodes).
- Charge selector for liquid/gel electrolyte batteries.
- Low residual fluctuation on output (ripple lower than 30 mV RMS).
- Compatible with every kind of generator.
- Can work in a wide range of ambient temperatures.
3 Step automatic charge
BULK phase (constant current)
ABSORPTION phase (constant voltage)
FLOAT phase (maintenance)
Universal AC Network: models DR
Protections:
- Reverse polarity (with internal fuse)
- Overload
- Output short circuit
- Overheating |
|
Important advantages:
- Multiple outputs in order to charge more groups of batteries (internal battery isolator diodes).
- Charge selector for liquid/gel electrolyte batteries.
- Low residual fluctuation on output (ripple lower than 30 mV RMS).
- Compatible with every kind of generator.
- Can work in a wide range of ambient temperatures.
3 Step automatic charge:
BULK phase (constant current)
ABSORPTION phase (constant voltage)
FLOAT phase (maintenance)
Universal AC Network: models DR
Protections:
- Reverse polarity (with internal fuse)
- Overload
- Output short circuit
- Overheating |
|
Battery chargers/charging converters – always a full battery
Starter batteries and leisure batteries are designed for different tasks. Starter batteries, in order to start the engine, must initially supply a high current level and will then serve as an energy buffer with smaller partial cycles. Supply or leisure batteries, by contrast, are charged and discharged at lower current levels for longer periods of time, which means they are subjected to significantly higher loads. Correct charging is the key to success. With a complete range of IU- and IU0U battery chargers, WAECO offers optimum charging technology for gel and AGM supply batteries. In each case, the consumed battery capacity should be replaced by a full battery charge. Even after longer journeys, with additional charge from the generator, the battery should immediately be connected to the power supply! Alternatively, you can use a PerfectCharge IU charging converter. These units guarantee optimal charging during the drive. How powerful a battery charger has to be depends on the battery capacity. As a rule of thumb, the charging current of the battery charger should be at least 10% of the battery capacity. |
|
When setting up the battery part of your 12 or 24V system, the required capacity and battery type are not the only things you need to consider: the vital components around the battery are at least as important for the charge current supply, ease of maintenance and extra safety.
Mastervolt provides you with all the necessary high quality items to perfectly round off your installation, guaranteed worldwide. |
|
The DC WhisperGen™ heat and power system is a uniquely quiet, independent power generation and heating system adapted for the marine sector, mobile, and remote home environments.
It provides power to automatically charge batteries that run all of the onboard / remote applications anytime.
It automatically provides hot water and also heat for a warm and dry living environment inside.
|
|
The Sinergex PureCharge series are fully automatic and intelligent battery chargers. Using microprocessor and switch-mode technology, the PureCharge battery chargers carefully assess the battery and then deliver
the optimum charge required. Being a true 3-stage battery charger, the
PureCharge delivers charges in bulk, absorption and float stages, each stage delivering the optimum charge for the best performance and power for your battery. By incorporating the float charge stage, the PureCharge battery charger allows you to set and forget, while your batteries are automatically maintained. By implementing the latest technology, PureCharge battery chargers are extremely light in weight and very compact in size and can be used and installed almost anywhere. |
|
| ... products without information |
| |
|
|
