|
|
Still the first choice for boat owners the world over, Scanstrut Mast Mounts are the ultimate solution for mounting radars on yachts masts.
Raising the antenna clear of any obstructions or interference, the mast mount is a classic and reliable installation.
NEW mounting foot design for 2008 - even easier installation.
Features
- Easy and quick to install with all fastenings supplied
- Attached to mast by four swivel feet matching the profile of any mast
- 12 point fixing using highest quality Monel rivets for a secure installation
- Nylon washers for all fastenings to protect paint finish
- Waterproof cable grommet included to seal cable entry into mast
|
|
Contact PYI for your custom electronic mounting solutions. We make specialty products for a wide range of customers from individual boat owners to production boat builders, we can design and build a mount for you. Our fabrication shop can build a wide variety of styles to meet your requirements. We have aluminum airfoil and round extrusion that we can use to design the perfect mount for your application. Examples of some of these solutions are shown in the pictures above. Lead time on customs orders is generally 3-4 weeks. Please fill out the form below to start the process.
|
|
|
Our Satellite Antenna Pole Mounts are constructed from high quality marine grade aluminum tubing with an Aluminum Die-Cast Base and Top, then treated with an anodized primer and then finished with a brilliant white powder coated finish. Designed specifically to fit all Satcom/TV Domes. Available in 9 in. to 10 ft. lengths. The last number at the end of the part number indicates the Pole length desired. For example, A 5' pole for a KVH 4 would be AP-4B-5.
|
|
Available as a deck mounted or through deck installation:
Deck Mounted
Features
- Ideal for installations on decks, cabin roofs, low arches and other areas where minimal elevation is required
Through Deck Mounted
Features
- Provides maximum stability for taller installations and heavier antennas
- Recommended minimum of 0.6m / 20" below deck
|
|
Scanstrut's SC100 Pole Mount allows installation of your radar or small satcom antenna onto the deck or transom of your boat.
Features
- Adjustable base, able to rotate through 360° and angle from horizontal all the way to vertical
- Unique pole extrusion accommodates two cable channels with a cover strip to hold cables in place
- Supplied with two support modules providing maximum fore / aft and sideways bracing
- Easily removed for racing or winter storage, leaving just low profile base on deck
|
|
| ... products without information |
| |
CALIPSO
This is the new INMARE design of a protection system for anchor windlasses.
It avoids any anchor traction loads on the windlass.
It provides protection for the anchorage.
Refined with a hand-made splice, it is equipped with a 14 mm polyester line, an outstanding shock absorber and a hook that can be installed on 6-12 mm chains.
|
|
|
The main innovation of the multipurpose HRC hand-held remote control is the built-in LED lamp, facilitating operation in the dark. This is the only hand-held remote in the nautical sector with this exclusive feature.
|
|
All the features of the AA560 plus options to control a bow thruster or deck lights and anchor wash.
- High level wireless transmission security - 2.4GHz ISM band
- Hand held controller displays rode count plus signal strength and battery level
- Ergonomic shape with wrist strap connector
- Water resistant to IP65
- Rubber cover moulding for grip and non slip protection
- Console holder and protective cover
- Shockproof
- IEEE 802.15.4 compliant
|
|
With safety cover to prevent accidental push-button operation.
MOD. 900 / DW - Anchor lowering switch. White.
MOD. 900 / UW - Anchor lifting switch. White.
MOD. 900 / DB - Anchor lowering switch. Black.
MOD. 900 / UB - Anchor lifting switch. Black.
|
|
Maxwell heavy-duty, weather resistant units have a UV stabilised water proof diaphragm and are supplied complete with mounting instructions and screws.
- Rated at 200 amps and suitable for 12V or 24V applications
- Nickel-plated copper contacts ensure corrosion-free, reliable operation
- Available in UV stabilised plastic or polished stainless steel covered versions
- Uncovered plastic versions are also available.
|
|
The Control Box is an electric unit made up of two remote control switches enclosed inside a special container which protects it from marine corrosion. The entire unit has been designed with a view to simplifying and speeding up the various electrical connections.
For this purpose there is no need to open and/or pierce the container, as all the terminals and the panel for the electrical connections are perfectly accessible from the outside.
Outer construction in self-extinguishing polyester resin, resistant to shock and marine corrosion. Degree of protection IP 56 - protection against deckwater.
|
|
Wireless remote control:
With a radio control installed you will have full control of windlass operation where ever you are on board. The control consists of a transmitter and a receiver. With the AutomaticDownTM function the windlass will run automatically for 25 seconds before stopping. To enable the AutomaticDownTM just press the DOWN button on the receiver. To stop the AutomaticDownTM at any time, press DOWN once on the receiver.
|
|
This new remote control model LIBERTY has an elegant and functional design. The soft rubber case, which covers sideways the remote control, allows a safe and handy taking under any condition.
LIBERTY is completely waterproof and supplied with waterproof plug and socket (IP68) of the finest quality.
The extending flexible cable (approximately 4 metres) gives the maximum freedom on board during anchoring manoeuvring.
|
|
|
To operate your windlass safely in all weather conditions you need top quality switch gear that can stand the roughness of the sea. Anchorlift uses only the best of materials to ensure you a sae and long service life of your equipment.
|
|
Foot switches:
UP & DOWN switch with a safety cover to prevent accidental push button operation. Usually mounted on deck near the anchor windlass. Available with black or white cover.
|
|
| ... products without information |
| |
Contact PYI for your custom electronic mounting solutions. We make specialty products for a wide range of customers from individual boat owners to production boat builders, we can design and build a mount for you. Our fabrication shop can build a wide variety of styles to meet your requirements. We have aluminum airfoil and round extrusion that we can use to design the perfect mount for your application. Examples of some of these solutions are shown in the pictures above. Lead time on customs orders is generally 3-4 weeks. Please fill out the form below to start the process.
|
|
|
Our Satellite Antenna Pole Mounts are constructed from high quality marine grade aluminum tubing with an Aluminum Die-Cast Base and Top, then treated with an anodized primer and then finished with a brilliant white powder coated finish. Designed specifically to fit all Satcom/TV Domes. Available in 9 in. to 10 ft. lengths. The last number at the end of the part number indicates the Pole length desired. For example, A 5' pole for a KVH 4 would be AP-4B-5.
|
|
Available as a deck mounted or through deck installation:
Deck Mounted
Features
- Ideal for installations on decks, cabin roofs, low arches and other areas where minimal elevation is required
Through Deck Mounted
Features
- Provides maximum stability for taller installations and heavier antennas
- Recommended minimum of 0.6m / 20" below deck
|
|
Scanstrut's SC100 Pole Mount allows installation of your radar or small satcom antenna onto the deck or transom of your boat.
Features
- Adjustable base, able to rotate through 360° and angle from horizontal all the way to vertical
- Unique pole extrusion accommodates two cable channels with a cover strip to hold cables in place
- Supplied with two support modules providing maximum fore / aft and sideways bracing
- Easily removed for racing or winter storage, leaving just low profile base on deck
|
|
|
Sold separately or with a furler, this new patented system from Karver allows to lock the stay and the sail on the mast very easily. From 1,5T to 15T
|
|
The KF-H (patented) is the only system on the market that combines the furling and the locking mechanism in the same unit.
The lock mechanism allows to lock the swivel, the halyard and the sail directly onto the mast.
The lock works automatically using the halyard to lock and to unlock.
Used for flying sails (such as staysails and gennakers) it replaces the usual block system where luff tension comes from the long 2/1 or 3/1 halyard and a lot of compression in the mast.
The system and the sail are locked on the mast and the luff is tensioned from the bottom by a 2/1 or 3/1 purchase placed under the lower part of the furler.
The compression in the mast is minimized and it is possible to use a smaller and lighter halyard as it only carries the weight of the sail.
Once the system is dropped on deck, there is only the very light hollowed male end remaining on the mast and the furling-lock mechanism is on deck and accessible for maintenance.
EXCLUSIVE ADVANTAGES OF THE K-FH
-no more structural halyard
-no more blocks above the swivel
-less compression in mast = safer
-smaller halyard diameter = lighter
-straighter sail luff
-very light weight at the top of the mast when system is not in use.
|
|
| ... products without information |
| |
|
