|
|
The Series 300 Rudder Angle Indicator provides an accurate and continuously updated indication of your rudder position. In a stand-alone system up to five indicators can operate at the same time in conjunction
with the standard RFU 400 follow-up, No master indicator is required. Installation is easy and requires only a shielded 2 conductor wire, 24 AWG for cable runs up to 65' (20 meters).
|
|
Awareness of the rudder angle is an important safety factor. This is especially true while moving in and out of your berth, drawing alongside another boat, picking up a skier, mooring, or any other "close call" situation. Davis' Rudder Position Indicator gives instant visual reference of rudder angle.
The pointer swings a full thirty degrees with each revolution of the wheel. Mounts directly to your hub (approximately 2" (5 cm) in diameter) with a self-adhesive pad . Rugged, hermetically sealed, weatherproof, and sunproof housing ensures long life. No cables, adjustments, or electricity required; gravity power makes it simple and service-free. Suitable for boats with mechanical and single station hydraulic steering systems.
|
|
|
The steer pilot is a highly innovative instrument that has proven its value out on the racecourse many times since it was first introduced as part of the NX2 system in 2005. Put in simple terms, this invaluable instrument continuously displays to the helmsman the direction in which he should be steering in order to reach a given point in the fastest and most efficient way. It does this by combining data from the compass, speed transducer and GPS and when required analyses it against a boat's technical specification, most commonly the polars, to determine the best route. When the helmsman deviates from that route the needle instantly moves away from the centre line, indicating in the clearest way possible the direction and extent of that deviation.
|
|
Multi Control FI-301: Displays all the data available in the network. It even works as a remote control unit for other instruments networked.
Speed FI-302: Displays ship speed, depth trip distance, odometer distance and average speed. It also functions as a stopwatch.
Wind Data FI-303: Displays digital and graphical readouts of true and apparent wind speed and direction, own ship speed through water and over ground, trip distance, etc.
Compass Data FI-304: Displays ship's heading relative to true north or magnetic north. A fluxgate or Satellite Compass may be used to feed heading information to the FI-304. Digital readouts can also be displayed with a simplified compass rose.
Multi XL FI-305: Facilitates easy monitoring of all the data available in the network with large alphanumeric characters. Please note that, to operate the FI-305, Multi Control instrument FI-301 is required within the network.
Wind Angle FI-306: Displays true or apparent wind direction with the zones in red and green.
Steer Pilot FI-307: Relays the data in the server to the network, enabling you to quickly set an exact course to steer towards your destination.
Please note that, to operate the FI-307, Multi Control instrument FI-301 is required within the network.
|
|
| ... products without information |
| |
The linear will provide the Servo unit with rudder angle for efficient steering. The Rudder Angle Transmitter is easy to fit direct to the Linear drive unit HP-40 (see image).
|
|
Multi Control FI-301: Displays all the data available in the network. It even works as a remote control unit for other instruments networked.
Speed FI-302: Displays ship speed, depth trip distance, odometer distance and average speed. It also functions as a stopwatch.
Wind Data FI-303: Displays digital and graphical readouts of true and apparent wind speed and direction, own ship speed through water and over ground, trip distance, etc.
Compass Data FI-304: Displays ship's heading relative to true north or magnetic north. A fluxgate or Satellite Compass may be used to feed heading information to the FI-304. Digital readouts can also be displayed with a simplified compass rose.
Multi XL FI-305: Facilitates easy monitoring of all the data available in the network with large alphanumeric characters. Please note that, to operate the FI-305, Multi Control instrument FI-301 is required within the network.
Wind Angle FI-306: Displays true or apparent wind direction with the zones in red and green.
Steer Pilot FI-307: Relays the data in the server to the network, enabling you to quickly set an exact course to steer towards your destination.
Please note that, to operate the FI-307, Multi Control instrument FI-301 is required within the network.
|
|
| ... products without information |
| |
Fits most 4"-5" hand grinders; adjust height with screws
Easy to install with band clamp
Clear plastic for improved visibility
Removable front edge of shroud for grinding close to wall or edge
Brush skirt for improved performance on textured surfaces
|
|
The Dustie™ dust control shroud fits most hand grinders including Makita, Bosch, Dewalt and more. It captures up to 99% of airborne particles for outstanding dust control that preserves air quality and protects workers from harmful silica dust, Hexavalent Chromium and silicosis caused from sawing, cutting and grinding concrete, stone, masonry, fiberglass and other construction materials. Meet OSHA guidelines for worker safety with the industry's best dustless grinding system.
5" size fits most 4"-5" hand grinders
7" size fits most 6"-9" hand grinders
Fast and easy to install
Captures 99% of airborne particulate
The Dustie™ dust control shroud installs fast and easy. The Flex-Flange™ connecting collar is built onto the dust shroud and simply tightens with a band clamp. There is no separate universal adapter to hassle with.
An optional cover plate can be used with a modified Dustie™ dust control shroud for tuck pointing, crack chasing and decorative concrete cutting applications. You need to cut a portion of the Dustie™ dust control shroud off to expose the leading edge of the blade. A cut line is molded into the dust control shroud to aid in the process. The optional cover plate simply snaps in place.
|
|
Stereofins with the angle in front of the blade from handmade multilayer fiberglass.
High quality fiberglass blades, made from the hand-laminated mixture of resins with fiberglass, processed in moulds under vacuum. The fins are sensitive and lightweight .
The angle in front of the blades allowing to keep the knees more straight saving your energy and making swimming more easy and convenience.
The blades are available in 4 standard levels of stiffness, which allows the perfect fit to the different types of spearfishing and to the specific requirements of each diver. We can add more stiffness upon request.
The blades measurements are 20cm x 85 cm, but we can customize the dimensions according to your special request.
The fins also has full-length rubber rails for protection, hydrodynamic stability and for also a silent swimming. You can choose different kind of rubber protection, additional small flippers, and a new design for the end of the blade.
All our freediving fins and blades come with a one-year full warranty for materials and craftsmanship.
|
|
|
|
