|
|
With the BRAVO 10 double chamber pump, inflation to the recommended pressure of all fabric or rubberised boots, can easily be achieved with very limited effort.
Should you not use a pressure gauge to control the boat pressure. BRAVO 10 footpump is provided with a visual pressure indicator to warn against over-inflation.
- Manufactured from strong nylon reinforced fiber glass
- Unalterable by the sun or sea environment
- Biq but lightweight due to the use of synthetic materials {1.9 Kg)
- 4 antislip feet for greater stability
- Standard crush resistant hose
- Universal hose/valve adaptors supplied as standard
- Dimensions: 35x25xh 8 cm
|
|
- Inflates a 4 man dinghy in 1-2 minutes
- Supplied with an adaptor for all major inflatable boats
- Deflates a dinghy flat and ready to pack
- One handed operation
- Airflow 550L / Minute
- 25 Amps Max
|
|
Professional electric inflators designed for the sector's operators: boats manufacturers, building yards, repairers and setters.
- Air high volume and pressure, which is sufficient to reach the correct pressure in every kind of boat and/or inflatable structures in general (tents, etc.]
- Provided with connectors for any kind of use.
- Designed to inflate and to deflate.
- Motors and fan system of great efficiency and reliability.
|
|
Very resistent hand pump, destined to a professional use.
- Single-action pump; diameter 12,5 cm (5")
- Can inflate and deflate;
- Capacity 400 l/min at 60 strokers/min;
- Really strong body made of PVC;
- Adjustable support for the hose (it makes the inflation and deflation easier);
- PVC hose (length 2 mm/78")
- Gasket made of silicon rubber. Spare gasket for the piston inside the pump.
- Height 70 cm (28")
- Provided with adaptor for the most common type of valves.
|
|
This 110-volt pump will inflate or deflate your inflatable in a hurry. It comes with an assortment of nozzles to adapt to your needs and has a high-volume, low-pressure output to get the job done quickly.
|
|
| ... products without information |
| |
Aqua Jet Uno WPS 3.5 & 5.2
Medium demand unit with a single Aqua Jet WPS capacity 13 l/min or 20 l/min fixed on a base with PUMProtector inlet strainer and a 2 litres pre-pressurized accumulator tank.
Aqua Jet Duo WPS
High demand unit with two parallel-connected Aqua Jet WPS capacity 40 l/min fixed on a base with PUMProtector inlet strainers and a 2 litres pre-pressurized accumulator tank.
Aqua Jet Uno Max WPS 2.9 & 3.5
Medium demand unit with a single Aqua Jet WPS with capacity 11 or 13 l/min fixed on a wooden panel for easy and efficient installation. The unit includes a PUMProtector inlet strainer and a 2 litres pre-pressurized accumulator tank.
|
|
Aqua Jet Flow Master 5.0 WPS
The ideal choice for pressurizing water in a closed system. The digital controller adjusts water flow as the demand is increased and decreased while maintaining a very smooth flow. The unique variable flow feature of the Flow Master pump allows the pump to be mounted without an accumulator tank and still maintain an even flow regardless if one or multiple taps are being used.
|
|
Aqua Jet WPS 2.4, 2.9, 3.5, 4.0 & 5.2 - Aqua Jet Water Pressure Systems
The five chamber Aqua Jet WPS-series provides a reliable heart for small boat and recreational vehicle water pressure systems. Compared to conventional three or four-chamber diaphragm pumps, the Aqua Jet demonstrates dramatically lower noise and water pulsation characteristics.
It is recommended to install the WPS-pumps with an accumulator tank. Always use a PUMProtector inlet strainer before the pump intake.
|
|
Features:
%u2022 Integrated pump and tank system
%u2022 May be mounted vertically or horizontally
%u2022 Flow rates up to 4.5 US Gallons/min (17 Lires/min)
%u2022
Specifications:
Voltage Options 12,24,32 & 115v
Flow Rate Flow rates up to 4.5 US Gallons/min (17 Lires/min);
Max. Pressure 40psi (2.8bar)
Port Type 1/2" hose barb
Strainer Included
|
|
• Integrated pump and tank system
• May be mounted vertically or horizontally
• Flow rates up to 4.5 US Gallons/min (17 Lires/min)
|
|
| ... products without information |
| |
Genuine Sherwood Impellers can be identified using their overall dimensions.
8000K - width 3/4" diameter 1-9/16"
09000K - width 7/8" diameter 2-7/16"
09959K - width 1-1/4" diameter 2-7/16"
10077K - width 25/32" diameter 2-1/4"
10615K - width 1-5/8" diameter 2-9/16"
15000K - width 2" diamter 2-9/16"
17000K - width 2-7/8" diameter 3-5/16" (keyed shaft)
18000K - width 4" diameter 3-3/4"
22000K - width 4-5/16" diameter 4-1/2"
26000K - width 3-1/8" diameter 3-3/4"
27000K - width 2-7/8" diameter 3-5/16" (splined shaft)
|
|
Take good care of the cooling system – change to a new impeller every year!
The impeller is a very important security device. Its task is to pump the water through the cooling system of the engine. But remember that the impeller should be replaced every year. And always make sure you get a Johnson Pump Brand original impeller. Then you’ll know that it matches your pump exactly.
Remove the impeller with a slip joint plier or an Impuller.
|
|
Impeller removal has been made easier with the patented Sherwood Impeller Puller. Simply thread the puller into the threaded end of select Sherwood impellers and the bolt presses on the shaft, pushing the impeller out of the pump.
Sherwood's Impeller Puller is utilized on five different impeller sizes. Impeller puller 23631 is used on the 17000, 18000, 22000, and 27000 impellers. Impeller puller 24412 is used on the 27000 impeller.
|
|
|
The sound insulation of our hoods is approx. 10-18 db(A). For better ventilation, our hoods are equipped with additional fans (1~ 230 V). These hoods are available as complete units including vacuum pumps (compressors) or equipped for retrofitting of your existing vacuum pumps (compressors).
|
|
| ... products without information |
| |
| ... products without information |
| |
Mimic panel X for navigation lights and bilge pump control for motor yacht.
|
|
|
|
see the results for the following category : 
