|
|
voltage : 220 voltes
power : 1500 litres/mn
pressure :250 mbar/3,6psi
|
|
- Inflates a 4 man dinghy in 1-2 minutes
- Supplied with an adaptor for all major inflatable boats
- Deflates a dinghy flat and ready to pack
- One handed operation
- Airflow 550L / Minute
- 25 Amps Max
|
|
Hi-Speed inflator deflator
The high speed is a high quality unit for the rapit inflation and deflation of all inflatables. Inflates a typical four man dinghy in as little as one to two minutes. Adjustable nozzles have been included for most inflatables and valve types.
|
|
This 110-volt pump will inflate or deflate your inflatable in a hurry. It comes with an assortment of nozzles to adapt to your needs and has a high-volume, low-pressure output to get the job done quickly.
|
|
2.2 lbs/cu ft (35.2 kg/cu m) closed-cell polyethylene (PE) foam
Natural color (off-white)
Water absorption:
Less than 0.3 lbs/sq ft exposed (1.5 kg/sq m)
Less than 3% by volume
Per ASTM D3575-Suffix V, EN 28301, ISO 2581 tests
Buoyancy: 58 lbs/cu ft (930 kg/cu m)
Completed foam sections heat-welded (not glued) and hot-wire shaped to finished profile
|
|
CPI's air collar is constructed of 100% polyurethane (PU) for its outer cover and contains our patent-pending removable bladders constructed of urethane film.
The collar is outfitted with stainless steel D-rings for tie downs and lifelines. Our collars are built to the customer's specs and can include a variety of trim packages.
Standard rope strips or custom attachment methods are available and can be configured to the customer's specs.
|
|
| ... products without information |
| |
Racor now offers replacement filters for marine applications. These filters are direct replacements for the intake air filter portion of vairous brands of air filters/silencers
|
|
Eliminate Fuel Vent Line Overflow During Refueling
Next time you fill up, watch your fuel vent line. A typical refueling will send up to a half gallon or more of fuel spilling overboard. Fuel spillage is not only expensive, it's absolutely deadly to fragile lakes, rivers and waterways. USCG and other regulations prohibit the discharge of oils including civil and criminal penalties.
Installed in the fuel tank vent line, the Racor Fuel/Air Separator efficiently separates air from fuel forced into the line. Air is vented, and all fuel is returned to the tank. The Fuel/Air Separator captures fuel normally discharged due to agitation and thermal expansion up to 2.4 PSI. It also eliminates damage to expensive striping and labels and protects finishes from fuel stains. The unit is maintenance free -- there's nothing to rust or corrode.
The Racor Fuel/Air Separator fits neatly into your vent line, actually replacing a section of the line. One Fuel/Air Separator unit is required for each vent line, both models fit 5/8" vent lines. Fittings are included.
|
|
To check the pressure in the cylinder
Supplied with a screw purge
Available with yoke or DIN 300 Bar or M26 x 2 ISO 230 bar (Nitrox/O2) connections.
|
|
| ... products without information |
| |
| ... products without information |
| |
|
Similar in design to Eastman's Brute, the Air Brute is a lightweight pneumatically-powered machine perfect for cutting intricate patterns and straight lines. The air power allows for seamless cutting in a damp environment, where an electric powered machine cannot be used for extreme dust and fiber laden conditions.
|
|
|
The Buzzaird is designed with a 20,000 RPM pneumatic motor suitable for wet environments. It is an extremely powerful rotary shear suitable for cutting single-ply leather, rubber, plastics, woven glass, coated materials, and much more. Available options include a Pelican head or swivel sharpener. Optional swivel sharpener is equipped with a 30 degree ball tip shear plate for close edge trimming.
|
|
| ... products without information |
| |
|
A Webasto air heater is a cost-efficient solution for heating the interior of a boat. Thanks to the high-performance hot air fan your boat interior quickly reaches the desired temperature. The air heater offers totally independent operation and it is extremely quiet.
|
|
Special technical features
- Automatic, continuous room temperature control with temperature preselection
- Efficient power stage to shorten the "heating up time"
- Electronic speed control with soft adaptation, thus low in noise and power-saving
- Integrated control unit with TRS/ADR function (diesel)
- Fully electronic control by microprocessor
- Permanent function monitoring
- Ventilator function for summer operation possible (AIRTRONIC)
- Error diagnostics
- Low maintenance and easy to service
|
|
Diesel Variant (D)
Voltage V 24
Heat flow W Small Large
3500 8000
Heater air flow rate kg/h 310 310
Fuel consumption l/h 0.40 1.05
Mean electr. power in operation W 115 115
Weight kg 14.00
Size mm 653x260x250
|
|
Diesel Variant (D)
Voltage V 24
Heat flow W Small Medium Large Power
1000 2000 3000 4000
Heater air flow rate kg/h 65 110 150 185
Fuel consumption l/h 0.13 0.25 0.38 0.51
Mean electr. power in operation W 7 13 24 40
Weight kg 4.50
Size mm 371x140x150
|
|
Diesel Variant (D)
Voltage V 12
Heat flow W Small Medium Large Power
1200 2700 4800 5500
Heater air flow rate kg/h 125 180 275 280
Fuel consumption l/h 0.15 0.34 0.58 0.66
Mean electr. power in operation W 15 30 80 85
Weight kg 9.30
Size mm 530x170x170
|
|
The ORIGINAL Patented Direct Impingement Mix AIR-PURGE Spray Gun for Foam and Plural-Component Coatings.
All GlasCraft dispensing systems utilize our exclusive air purge, solventless direct impingement mix, Probler or Probler P2 Guns.
The Probler has been the industrys leading air purge spray gun since it was patented in 1974. Since then, all other air purge guns have been modeled after this industry benchmark.
With the Probler, time consuming and difficult adjustments common with mechanical purge spray guns were eliminated. Fewer adjustments meant it was much easier to set-up and simple to use and operate. GlasCrafts breakthrough with the patented Probler spray gun actually helped applicators increase production by reducing difficult procedures and adjustments.
|
|
The Probler P2 from GlasCraft is the ultimate contractor gun!
Why?
Less maintenance, less downtime, very user friendly, and the lowest parts consumption in the business!
The NEW and Patented Probler P2 Plural-Component Spray Gun for Foam and Coating applications offers technology that is only available from GlasCraft.
The P2 has the most responsive trigger action available in the market today thanks to GlasCraft's patented dual-piston design which provides over 300 lbs. of force.
The 2-piece spray chamber and tip insert design is another GlasCraft patented technological advance which allows for more spraying uptime
The Probler P2 has lower parts consumption than any other gun available in the marketplace today!
|
|
Introducing The Revolution Internal Mix Air Purge Spray Gun
Offering the Advantage of Internally mixing resin & catalyst without the constant concern of gelling the gun. Its lightweight and simple design is the ultimate in Polyester Spray Gun Development
Features:
Enviromentally Sealed Valve Components
Single Operating Piston
Air Purge Eliminates Solvent Waste
Pneumatic Trigger
Automatic Air Flush
High Flow Passageways reduce Spray Pressure
Self Adjusting Fluid Seals
Low Emission, Non-atomized Spray Package
Hardened Components
Low Repair Costs
Less Down Time
Less Waste
More Production
Cutter Mounting Kit Available
Accessor and Robotic Adapters Available
|
|
| ... products without information |
| |
|
