|
|
voltage : 220 voltes
power : 1500 litres/mn
pressure :250 mbar/3,6psi
|
|
- Inflates a 4 man dinghy in 1-2 minutes
- Supplied with an adaptor for all major inflatable boats
- Deflates a dinghy flat and ready to pack
- One handed operation
- Airflow 550L / Minute
- 25 Amps Max
|
|
Hi-Speed inflator deflator
The high speed is a high quality unit for the rapit inflation and deflation of all inflatables. Inflates a typical four man dinghy in as little as one to two minutes. Adjustable nozzles have been included for most inflatables and valve types.
|
|
This 110-volt pump will inflate or deflate your inflatable in a hurry. It comes with an assortment of nozzles to adapt to your needs and has a high-volume, low-pressure output to get the job done quickly.
|
|
| ... products without information |
| |
Genuine Sherwood Impellers can be identified using their overall dimensions.
8000K - width 3/4" diameter 1-9/16"
09000K - width 7/8" diameter 2-7/16"
09959K - width 1-1/4" diameter 2-7/16"
10077K - width 25/32" diameter 2-1/4"
10615K - width 1-5/8" diameter 2-9/16"
15000K - width 2" diamter 2-9/16"
17000K - width 2-7/8" diameter 3-5/16" (keyed shaft)
18000K - width 4" diameter 3-3/4"
22000K - width 4-5/16" diameter 4-1/2"
26000K - width 3-1/8" diameter 3-3/4"
27000K - width 2-7/8" diameter 3-5/16" (splined shaft)
|
|
Impeller removal has been made easier with the patented Sherwood Impeller Puller. Simply thread the puller into the threaded end of select Sherwood impellers and the bolt presses on the shaft, pushing the impeller out of the pump.
Sherwood's Impeller Puller is utilized on five different impeller sizes. Impeller puller 23631 is used on the 17000, 18000, 22000, and 27000 impellers. Impeller puller 24412 is used on the 27000 impeller.
|
|
|
Standard 2 inch panel mount visual/audible discharge indicator, solid state one piece construction, simple three wire installation, 12/24 VDC operation, Exceptionally low power drain, Replaces standard indicator lamp, Weather proof system test button, Marine ISO-8846
|
|
The Bilge Alert™ system uses a patented Mirus™ field effect detector cell, which produces a micro-electrical field that detects disruptions caused by water and fluids. When activated the sensor will trigger a 100db piezo alarm and an LED light on the control panel.
The sensor measures a small 26 mm wide x 64 mm long x 5 mm thick (1.04 x 2.5 x 0.2 in) which makes it very easy to mount. Detector cells are totally sealed, are never in contact with the water, will not corrode and are not affected by oil or foreign debris.
|
|
| ... products without information |
| |
... see all the products in the category
Alarms
|
|
This new medium demand unit from Johnson Pump consists of an Aqua Jet WPS five-chamber diaphragm pump integrated with a pre-pressurised 2 liters accumulator tank and inline strainer. The unit's design allows for either vertical or horizontal installation.
|
|
• Integrated pump and tank system
• May be mounted vertically or horizontally
• Flow rates up to 4.5 US Gallons/min (17 Lires/min)
|
|
|
The most advanced system available, this fully-automatic, quiet unit pumps tasteless, odorless water smoothly and consistently. Self-priming, corrosion-resistant and NSF certified tank. The result is longer life, reduced cycling, smooth flow and less wear on the pump. As always, the pump can run dry without damage.
|
|
|
The Rhine current drinking water plant RH 028 is suitable for occupation ships and large yacht ones. Equipped with a calmly running, sucking in, single-step centrifugal pump. It produces a pressure up to 3 bar. The pump made of brass and high-grade steel is manufactured. The plant consists 22 of an l high-grade steel pressure vessel, pump with adjustable push button switch and Verbindungsschlauch with check valve. The pump can be dismantled by the tank and set up separately. On request the plant is available also with second and third compression phase, so that a pressure up to 5 bar can be achieved.
|
|
| ... products without information |
| |
|
The sound insulation of our hoods is approx. 10-18 db(A). For better ventilation, our hoods are equipped with additional fans (1~ 230 V). These hoods are available as complete units including vacuum pumps (compressors) or equipped for retrofitting of your existing vacuum pumps (compressors).
|
|
PROMAGUARD from Soundown is a new concept in passive fire protection applying
microporous insulation technology. Thanks to its exclusive engineered mineral matrix, PROMAGUARD features unique benefits and provides many direct advantages with weight savings of up to 3 times lower than conventional solutions and materials making the panels ideal for applications on high
speed vessels. PROMAGUARD has been designed to meet SOLAS, IMO & MCA standards for passive fire protection. PROMAGUARD is the Solution for all insulating
and fire protection systems for bulkheads and deckheads on aluminum, GRP and steel structures requiring both extremely lightweight and thin insulation.
PROMAGUARD provides the lowest conductivity compared to conventional materials, as illustrated in the graphic. As a result, 10mm of PROMAGUARD
provides the same heat loss and insulation as approximately 50mm of
fibrous materials (depending on density and temperature). At 2.4Kg/m2, 10mm-thick PROMAGUARD provides the lightest possible weight panel as part of an A60
class fire rated system.
|
|
| ... products without information |
| |
| ... products without information |
| |
Mimic panel X for navigation lights and bilge pump control for motor yacht.
|
|
|
|
see the results for the following category
